Brief:
T' BSD Intrepid is a 2-stage interchangeable high powered rocket. Begad! Versions can be 38mm boost t' a 29mm rocket, a single stage 29mm rocket, matey, or a single stage 38mm rocket. Well, blow me down! Dual deployment was altered and timer bay was added by the builder.

Construction:
Body tube material be t' typical glassine coated cardboard. Ya scallywag! Fins and bulkheads were aircraft quality 3/16" plywood. Arrr! Ahoy! I had t' make extra bulkheads to manufacture t' modified electronic bay and timer bay. Ahoy! T' kit included plastic rivets, rail buttons, arrr, 9/16" tubular nylon shock cord, and BSD's motor retention system. Well, blow me down! Since t' possibilities for recovery were so varied, me bucko, shiver me timbers, I was required t' provide me own parachute. Begad! Attachment hardware be also included. Ya scallywag!

PROs:

• T' kit, arrr, as advertised, me hearties, is a very simple kit t' construct.
• T' instructions were well above average. Avast, me proud beauty! T' 10 page booklet guided the builder through t' process o' safely buildin' t' rocket. Arrr! A multitude of photos, shiver me timbers, nay drawn pictures, arrr, helped show each step. Begad! Additional tips were also added t' such things as applyin' fillets t' fins and launch lugs.

CONs:

• Although a very good kit, ya bilge rat, thar are a couple o' things t' think about before building. Buildin' t' electronics bay needs a little thought before assembling. Ya scallywag! Blimey! As bought, me bucko, you are required t' reach into both t' main and drogue airframes t' insert and/or attach t' deployment charge. Blimey! Blimey! T' instructions didn't give much information on how t' use t' e-bay. Aye aye! Blimey! I ended up cuttin' a 3" band o' airframe from t' drogue tube then I epoxied it exactly halfway down a coupler tube. Avast! Blimey! A bulkhead is then epoxied inside one end o' t' coupler. I manufactured a support rin' from another coupler bulkhead and cut t' center out leavin' about 3/8". Avast! Blimey! Arrr! Blimey! I used this as a shelf t' set t' removable bulkhead on with a rubber gasket. Ya scallywag! Blimey! On both bulkheads I epoxied a 1" PVC pipe cap t' be used as a cup t' hold my ejection charge, a 2 bus connector that would accept a wire from me Missile Works RRC2 (with t' wire threaded through a hole drilled in t' bulkhead and epoxied t' seal it and then t' eye bolt t' hold t' tubular nylon recovery. T' removable bulkhead was retained in place by 2 threaded bolts epoxied t' the permanent bulkhead. T' all-thread passin' through t' bay allowed for holding the RRC2 on a wood sled with launch lugs big enough t' slide over t' bolts and into t' bay.
• 
• T' kit's instructions didn't really cover t' installation o' a timer, which o' course is needed t' use this rocket in a 2 stage configuration. Ya scallywag! Ya scallywag! I added a bay in betwixt t' sustainer fins t' keep it close t' t' motor it will light. Avast! I used a small brass tube t' connect t' bay t' t' aft end o' the rocket. I also didn't like t' arrangement o' t' sustainer t' booster mating. More on that in t' flight critique.

Finishing:
PROs:

• No special considerations were needed for t' finish. Aye aye! Well, ya bilge rat, blow me down!
• T' vinyl decals are great! They are so much better than t' waterslide type. Well, blow me down! Begad! BSD provided plenty o' extra decals such as CP, CG and Vent hole decals.

CONs:

• With vinyl decals you had better be sure you are puttin' t' decal where you want it. Begad! If you put it on wrong you will stretch it when tryin' t' pull it off. Blimey!
• As with all decals, if you do nay put a clear coat on top o' them the lifespan is shortened. Avast, matey, me proud beauty! Blimey! I found that vinyl decals it will start peeling, ya bilge rat, which is me fault, arrr, nay BSD's. Blimey! Blimey! If I were t' reconsider anythin' I would have slowed down and put a few clear coats on t' entire rocket, shiver me timbers, but I be eager t' fly it!

Construction Rating: 4 out o' 5

Flight:
T' recommended motors per t' BSD website are: Booster: 38mm; I211, I284, J350; Sustainer: 29mm; H128, H180, ya bilge rat, I200. Ahoy! On t' first flight I used a Pro38 I205 staged t' an AT H238. Begad! Prior t' this I had ZERO timer experience. Blimey! Avast, me proud beauty! T' boost was good but t' sustainer failed t' fire. My second try be with t' same set up. Arrr! T' altitude was only 1900', nay too impressive for a 2 stage rocket. Aye aye! My third shot was with a J350 in t' booster and an H180 in t' sustainer. Avast! This was t' best flight I have done. Avast! Straight as an arrow up, good stagin' to 3200', shiver me timbers, and a good recovery.

T' only CON to this rocket in flight be t' sustainer/booster set up. Ahoy! Ahoy! T' motor mount in the sustainer is designed too far up into t' body tube. Begad! Aye aye! When t' second motor lights, t' interior o' t' tube was severely scorched preventin' any future mate up with t' booster. Ya scallywag! Next time I would either redesign t' mate up, coat the interior o' t' sustainer portion with epoxy or fiberglass or use a small BP charge t' separate t' booster from t' sustainer prior t' ignition. Avast, me proud beauty! A little forethought on me part would have prevented this. Ya scallywag! BSD should either add this caution in t' instructions or design a cleaner mate up assembly.

Recovery:
T' recovery was pretty straightforward. Ya scallywag! Blimey! T' drogue separated at apogee and the main came out at 300'. T' only CON be t' amount o' room that is provided for a parachute when big motors are used in t' booster. Avast! Blimey! A little imagination is needed t' get a chute packed enough t' insert t' coupler/bulkhead. T' motor forward closure was only about an inch from t' bulkhead. Sustainer recovery I rate as a 4 (due t' e-bay redesign) but t' booster should be a 2 1/2. A little more room is needed.

Flight Rating: 4 out o' 5

Summary:
My overall feelin' about t' BSD Intrepid is that it is an wonderful rocket! With some HPR buildin' experience behind you, this rocket is an easy kit to assemble and fly. Ya scallywag! Begad! It allows for a lot o' modification if needed or desired. Begad! It was a great entry rocket for me into 2 stage rocketry.

Overall Rating: 4 out o' 5