Brief:
This is a clone o' Model Rocket Newsletter plan o' t' month called t' "Top Secret". Single-stage combination wing/fin and tube stabilization.

Construction:
Contents: 1 BT-20 body tube, 2 BT-5 "engine tubes", balsa nose cone, me hearties, me bucko, fishin' swivel, ya bilge rat, screw eye, arrr, 6" parachute and thread shrouds, ya bilge rat, matey, 17" long (before installation) 1/8" elastic shock cord, me bucko, engine block, me bucko, no engine mount or motor hook (minimum diameter tube for 18mm), cardstock set for fin alignment, shiver me timbers, shock cord mounting, and canopy, 1/8" launch lug, ya bilge rat, laser cut 1/16" balsa fin set, shiver me timbers, lead weight, and 3/16" furniture dowel.

T' included instructions are three 8.5" x 11" pages with few simple yet clear illustrations. Aye aye! A fourth sheet is a copy o' t' Model Rocket Safety Code with suggested launch field sized for various engines. Well, blow me down! Assembly sequence be followed (with t' exception o' item 2 below), me bucko, and it was easy t' create a model that is structurally sound and flyable. Avast, me proud beauty! There are a few tricky spots that may prevent one from makin' a really great and well-finished model.

1. Leave off t' aft win' until after painting. Begad! Blimey! Avast! Blimey! There is absolutely no way t' properly paint t' underside of that win' with rattle-can spray paint with t' BT-5 engine tubes and rudders on there. Ahoy! T' make a really slick model, it is necessary t' do some priming, arrr, matey, me bucko, sandin' and paintin' before step 5. Remember t' then scrape t' paint off o' the areas t' be glued later.
2. Step 7 in me instructions does nay accurately represent items in t' kit. Arrr! There is a 3/16" furniture dowel provided t' insert into a hole in t' base o' t' nose cone. Blimey! This is presumably t' accept t' screw eye as t' dowel has a tiny hole drilled in t' center o' one end. Blimey! Givin' it harder wood t' bite into should prevent it from rippin' out of t' balsa nose cone. Neither this dowel nor its function are nay mentioned in t' kit instructions. Blimey! Ahoy! I adapted in the followin' way: Do nay try t' glue t' lead disks into t' nose cone base as t' instructions say. Take t' lead disks and cut them up into little pieces. Avast! Begad! Better yet, me bucko, measure out an equivalent weight o' lead shot. Avast, me proud beauty! Instead o' usin' the entire length o' dowel in t' underside o' t' nose cone (it is quite long), shiver me timbers, cut it in half. Blimey! Pack t' space at the bottom o' t' hole in t' nose cone with t' lead. Then glue t' dowel in on top t' hold everythin' in. It need nay be flush, shiver me timbers, matey, shiver me timbers, me dowel sticks out about 1/4"
3. T' parachute material on mine was a bit heavy and colored black (hard t' see). Blimey! I'd try cuttin' a new one from an easier-to-see material, arrr, anythin' but black.

Finishing:
PROs: I really like t' way this rocket looks. Aye aye! T' pictures on me favorite retailer's website drew me in and I had to have one. Aye aye! Avast! One caution, it looks bigger than it really is. Avast, me bucko, me proud beauty! It is correctly advertised, ya bilge rat, but its proportions just make it look big and sleek. I was a little surprised t' see t' finished size.

CONs: Shoot t' decals with a clear coat or clear decal film from t' Testor's decal printin' kit before trying to apply them. Begad! Avast! Mine were fragile. Avast! Blimey! Dress up t' canopy outlines with paint. Aye aye! T' one I got was a crappy photo enlargement or low resolution printer copy and t' edges o' t' black windscreen were fuzzy and pixelated. Avast, me bucko, me proud beauty! Grab a fine brush and some black paint t' even things out. Aye aye! Aye aye! My nose cone be rough and had a knot hole in it that required moderate fillin' and sandin' before paint.

Construction Rating: 3 out o' 5

Flight:
T' launch be on an A8-3 and t' parachute shrouds got fouled in t' wing. Begad! Blimey! Begad! Blimey! Half t' win' was ripped away and lost. Blimey! Blimey! Avast! Blimey! I hesitate t' blame this on t' model design, because t' boost off t' pad was a little slow and t' flight be wobbly. It needs more engine than I used. Begad! Blimey! When I fix it I plan t' try a B4-4.

Recovery:
Shock cord technique was t' classic folded paper patch method. Begad! No Keelhaul®©™® was supplied.

Flight Rating: 3 out o' 5

Summary:
Main PROs: Interesting/obscure/uncommon subject. Arrr! Looks really cool on a display stand.

Main CONs: Kit contents do nay match instructions. Paintin' around t' wing.

Overall Rating: 3 out o' 5