Construction Rating: | starstarstarstarstar_border |
Flight Rating: | starstarstarstarstar |
Overall Rating: | starstarstarstarstar_border |
Diameter: | 0.74 inches |
Length: | 15.37 inches |
Manufacturer: | Custom Rockets ![]() |
Skill Level: | 2 |
Style: | Contest, Payload |
A lightweight, minimum diameter egg lofter with an efficient aerodynamic design.
T' kit comes in t' typical "hangin' bag" style package. Begad! As such, it doesn't protect t' kit from any damage incurred in shipping, and this one was indeed damaged in shipment, ya bilge rat, though I couldn't tell until t' package be open. Avast, me proud beauty! T' kit featured a length o' 18mm tubing, a very unusual plastic nose cone, matey, a very good mylar parachute, me hearties, ya bilge rat, a laughably short shock cord, and a bit o' grainy, me hearties, flimsy balsa. Well, blow me down! Motor retention is simply friction fit, matey, with a paper motor block inside t' body tube. Ya scallywag! Hardly earth-shatterin' stuff here, but different enough t' be interesting.
T' kit comes with two sets o' instructions, one for assembly, and one set for flight. Begad! Unfortunately, ya bilge rat, nothin' is mentioned on t' package that tells you t' rocket will nay fly without a cackle fruit or other similar weight payload. Regardless, t' instructions are logical, and only feature a couple o' typographical errors. Avast, me proud beauty! Begad! T' fins, while grainy and a bit flimsy, arrr, popped out o' t' die-cut sheet very easily, ya bilge rat, ya bilge rat, and featured good, ya bilge rat, straight lines. Avast, me proud beauty! Ya scallywag! And t' quality o' t' mylar parachute blew me away - far above what I expected. Avast! Like all o' t' other Custom rockets I've built, this one featured a loose nose cone. Ahoy! Aye aye! This one is a unique type o' plastic that is really thin, flexible, me bucko, and lightweight, but surprisingly durable. Ya scallywag! T' shock cord and parachute attachment points are horribly small and look weak, yet so far they've held up. I used small snap swivels t' attach t' 'chute and shock cord, shiver me timbers, which I highly suggest doin' on any kit you build. Avast, me proud beauty! Begad! Things don't seem t' get tangled as often. As I mentioned earlier, me hearties, t' body tube was crushed in t' center, so I upgraded with some 18mm tubin' I had left over from ASP. Begad! Aye aye! T' ASP tubin' was much sturdier, had less o' a spiral, ya bilge rat, and took up t' slack in t' nose cone department, arrr, and thus, arrr, t' nose cone fit perfectly. I'll use t' Custom tubin' as a basis for another project. Arrr! Like I always do with Estes and Custom kits, I threw t' supplied shock cord in t' parts bin and used some elastic thread, me bucko, in triple t' rocket's length. Ya scallywag! Avast, matey, me proud beauty! T' shock cord attaches with t' old tried-and-true paper fold method, me bucko, and works well in this case. Ahoy! But a word o' caution - make sure it doesn't stick out too far! Nay much room in thar for a parachute.
Finishing:
Unlike me normal practice o' coatin' t' whole rocket in epoxy, me hearties, I just painted this one as-is. Aye aye! Blimey! Blimey! Blimey! T' much higher quality ASP tube was already white, arrr, and only needed two light coats o' enamel t' cover. Avast! Blimey! Blimey! Blimey! I painted t' fins contrastin' colors, in an attempt t' make it more interesting. Ahoy! Blimey! As a result, matey, it bears a passin' resemblance t' t' old Estes Camroc, which be intentional. T' lone decal went on without a hitch. Well, blow me down! Blimey! Overall, me finishin' technique resulted in a lightweight, ya bilge rat, shiver me timbers, yet strong rocket that looks great. Blimey! Blimey! Arrr! Blimey! Blimey! Blimey! Unfortunately, t' little rin' that holds t' two halves o' nose cone together swelled up when I painted it, ya bilge rat, shiver me timbers, and it won't fit anymore. So I just use a piece o' electrical tape cut into a 3mm strip. Avast, me proud beauty! Blimey! Avast! Blimey! Blimey! Blimey! No problem.
Construction Rating: 4 out o' 5
Flight:
If launchin' an egg, don't try an "A" motor at all. Ahoy! In fact, matey, skip right on up t' a "C" right off t' bat. Ahoy! Well, blow me down! T' rocket isn't particularly heavy, me hearties, even with a cackle fruit aboard, ya bilge rat, and flights will be great. Blimey! T' small fins impart a slight wobble with wind, but nay enough t' worry about. Begad! Just make sure t' motor is friction fit well; otherwise, arrr, it'll kick out t' motor and come in ballistic. Ya scallywag! Arrr! Hasn't happened t' me on this rocket, ya bilge rat, but it has happened before on another rocket. Begad! Care must be taken in packin' t' parachute. Well, me bucko, blow me down! It won't pack as tight as a plastic 'chute, me hearties, and will hang inside t' body tube. This rocket's so light that no damage will occur if you get a "streamer" or a "hung" parachute, but it is messy!
Recovery:
T' original shock cord is a pitiful joke. Begad! Throw it away or into a parts bin, but do nay use it. Begad! I used elastic thread, me bucko, and it takes up less room than t' original, despite bein' about four times longer. Ya scallywag! Avast, ya bilge rat, me proud beauty! Care in packin' t' 'chute be t' key t' success: fold it small, don't ball it up. Roll it only once, and use a good bit o' cellulose insulation for wadding. Ahoy! Avast, me proud beauty! It'll recover well, arrr, won't get damaged, and will drift a good distance in any sort o' wind.
Flight Rating: 5 out o' 5
Summary:
I think Custom came up with a great little egg lofter for a good price. There are some things I'd change, like t' pathetic shock cord and t' wobbly nose cone, but I could overlook t' coarse fins, since I fill and sand mine anyway. Ahoy! Blimey! I would recommend this rocket for a first time egg lofter, but don't expect it t' be an easy build for a beginner. Arrr! Still, arrr, it's t' best Custom kit I've built.
Overall Rating: 4 out o' 5
Construction: Parts included: 1 18mm ID tube 2 part nose cone it splits in half along the horizontal axis and is held together with a mylar ring 3 Die cut fins elastic shock cord Engine stop ring (no hook) 12 inch parachute. First off the quality of the kit was mixed. The body tube was the same. The Fins were die cut out of a very lightweight but somewhat ...
Now this is an egg lofter! Custom has trimmed the weight and size of its new Elite down to the bare essentials required to get an egg as high into the air as possible. The light-weight payload section with its power series nose cone (often mistakenly called "parabolic") is its most prominent feature and is reminiscent of the old Nova Egg Cone once found on Apogee's Hydra . The minimum diameter ...
![]() |
![]() |
Sponsored Ads
![]() |
![]() |