| Construction Rating: | starstarstarstarstar |
| Flight Rating: | starstarstarstarstar |
| Overall Rating: | starstarstarstarstar |
Brief
T' Sky Shriek be clone number four o' t' original Goonybirds that I built. Blimey! And as such is another kit bashed Baby Bertha. Begad! Blimey! T' plans were downloaded from http://plans.rocketshoppe.com/estes/est0855/est0855.htm. Arrr! I then followed these t' build t' Sky Shriek with t' exception o' it havin' an 18mm motor mount instead o' t' 13mm mount that was in t' original.
Components
From Baby Bertha kit:
- 1- BT-60 Body Tube (cut t' 6" in length)
- 1- PNC-60 Nose Cone
- 1- Launch Lug
- 1- Engine Hook
- 1- Shock Cord
- 1- Assembled 12" Parachute
- 1- Mylar Retainer
- 1- Green Engine Block
- 1- Blue Engine Mount Tube
- 1- Centerin' Rin' Card
From me stock pile:
- 1- 1/8" Sheet o' Balsa (for cuttin' new fins and struts)
- 1- Sheet Decals (printed on computer paper and cut out)
Construction
T' only real Con t' this build be cuttin' all t' curves in t' new fins and t' holes for t' three struts, plus havin' t' shorten t' BT-60 tube t' 6". Blimey! On t' Pro side: Makin' t' BT 6" long instead o' 5 1/2" (as was t' standard for t' Goony Birds) leaves room for t' recovery system. Arrr! I was also able t' skip half o' step 4 because I'm usin' t' Baby Bertha NC. Blimey! Blimey! Just gotta remember t' add some nose weight. T' rest o' t' construction was by t' book with no problems.
Finishing
Finishin' be done in t' standard sand, prime, sand, arrr, and prime again with Rust-olium 2x white primmer. Well, blow me down! Blimey! Blimey! Blimey! Top half o' t' rocket was then painted with Krylon Gloss Red. Ya scallywag! Blimey! After second coat be applied rocket was set aside for t' day t' air dry. Once paint be dry, top o' rocket was masked off and bottom half painted with two coats o' Krylon Gloss Black. Begad! Blimey! Blimey! Blimey! Rocket was allowed t' dry again before removin' maskin' tape. Aye aye! Blimey! Blimey! Blimey! While rocket was dryin' again I set about printin' out t' decals. Well, blow me down! Blimey! Arrr! Blimey! Blimey! Blimey! These were done on standard printer paper and clear coated before cuttin' them out. Avast, me proud beauty! Blimey! Ya scallywag! Blimey! Blimey! Blimey! They were then attached with a glue stick. Ya scallywag! Blimey! Avast! Blimey! Blimey! Blimey! After allowin' some more dryin' time and checkin' that none were comin' lose, matey, ya bilge rat, entire rocket received a clear coat o' paint t' seal in decals. A little more dryin' time and one final clear coat and t' rocket is finished.
Flight
Maiden flight occured on 09-09-07 at Michigan International Speedway at a J.M.R.C. Aye aye! Ahoy! club launch on an Estes B6-4. Blimey! Rocket be almost a blurr as it left t' pad. Nice high flight with parachute ejection just past apogee.
So fast off t' pad almost missed t' shot
Recovery
Recovery be text book perfect. Begad! Parachute deployed fully and gave rocket a nice gentle decent with no damage on recovery.
Summary
This is another gem o' a flyer and be a fun build.
#Related Reviews
- Clone Cloud Hopper By Steve Lindeman
Cloud Hopper was my second Goonybird clone that I built by kit bashing an Estes Baby Bertha and as a result has an 18mm motor mount instead of the 13mm that the original Cloud Hopper had. Components Components used for this build were one Estes Baby Berha Kit (1261) and the plans ...
- Clone Missile Toe By Steve Lindeman
Missile Toe was number three in my line of cloned Goonybirds that was built by kit bashing another Baby Bertha kit. As such the plans and decals were downloaded from Ye Old Rocket Plans (http://plans.rocketshoppe.com/estes/est0854/est0854.htm) and used for construction guide. ...
- Clone X-15 By Steve Lindeman
In all fairness I can't do a brief description on this kit as there is a small story behind it. As is normal for me this is not an actual review of the Estes NASA X-15 (0889) [1988-1989]. It is a kit bashed, clone by transition. I came about the idea of doing the X-15 as the G-15 after ...
- Clone Zoom Broom By Steve Lindeman
Zoom Broom was the 1st of my Goonybird clones modified for 18mm motors as a result of being kit bashed from a Baby Bertha. Components Starting with a Baby Bertha kit (EST 1261) that I purchaced at my local Hobby Lobby, all components except the balsa wood and decals were used to ...
- Excelsior Rocketry Der Goony Max By Bill Eichelberger
Der Goony Max is an inspired bit of lunacy from Excelsior Rocketry, and I guess depending on where you stand on the Goony issue, this series is either genius or a waste of a good Baby Bertha. Speaking as the one-time-owner of an original Goonybird Cloudhopper, I happen to fall on the genius ...
- Kit Bash GoonyHawk By Steve Lindeman
Here I go again. For those of you that have followed my Goonyness this was Baby Bertha kit bash #14. Again this is not a kit review of the original Estes Hawkeye (Kit #0873) [1986-1996] It is another of my many kit bashes. All ...
- Kit Bash GoonAries SST By Steve Lindeman
Here I go again. For those of you that have followed my Goonyness this was Baby Bertha kit bash #10. Again this is not a kit review of the original Estes Aries SST (Kit #1927) [1983-1984]. It is another of my many kit bashes. ...
- Kit Bash Goony Target Drone By Steve Lindeman
Lucky or unlucky? For those of you that have followed my Goonyness this was Baby Bertha kit bash #13. As such I wanted to play it a little safer with this one so I choose a simpler design. Again this is not a kit review of the original Estes ...
- Kit Bash Goonymarc By Steve Lindeman
The Goonymarc was number eight in my line of modified Baby Bertha kit bashes. I started with the plans from Jim Z's for the Estes kit #654 with the thought of building the glider version of the Bomarc but ended up with the parachute version (kit #657). All templates and decals for this build ...
- Kit Bash NASA Goonasus By Steve Lindeman
One again this is not a kit review of the original NASA Pegasus (Estes Kit #1376) [1982-1986] but another of my many Baby Bertha kit bashes (#12 for those following my Goonyness). All fin patterns and decals came from http://plans.rocketshoppe.com/estes/est1376 ...
- Kit Bash Snarky Jr. By Steve Lindeman
The Snarky Jr. (a.k.a. Goony Shark) was kit bash #6 in what was to become a long list of Baby Bertha's that I converted into various Goony Birds and such. The inspiration for this one of course came from my DynaStar's - Snarky and the fact that I wanted to be able to fly it in the smaller ...
- Kit Bash Streamliner By Steve Lindeman
The Streamliner was the fifth in a series of Baby Bertha kit bashes that I did while building my Goonybird fleet. The first four kits were used to make four of the original Goonybirds from Estes but now it was time for somthing a little different. I remember seeing this model in a&n ...
- Kit Bash USGF Goonasus By Steve Lindeman
For those of you still following my Goonyness this was Baby Bertha kit bash #11. Again this is not a kit review of the original but another of my many kit bashes. All fin patterns and decals came from http://www.spacemodeling.org/JimZ/est0806.htm . The major ...
- Kit Bash USSF Goonyflash By Steve Lindeman
For those of you following my Goonyness this is Baby Bertha kit bash #9. So OK this is not a kit review so much as it's actually another of my kit bashes. All fin patterns and decals came from http://www.spacemodeling.org/JimZ/estes/est1909.pdf . The main ...
- Mo' Skeeter By Chris Gonnerman
This is my Mo' Skeeter, a 320% upscale of the classic Estes Mosquito . It's a rear-ejection model, which avoids the visible nose cone line that most Mosquito upscales suffer from. Components This rocket consists of a Baby Bertha cone , 6" of BT-60, 6" of BT-20, two 20-60 ...
- Modification Baffled-Boat-Tailed-Bigger-Baby-Bertha By Mike Goss
It all started one day after I opened a Baby Bertha kit and found that the motor mount had the wrong size adaptor rings. The rings were for a BT-50 and not a BT-20. I thought about replacing the rings with a correct set, but then the creative juices started to flow, what could I do with this ...
- Modification BioHazard By Dwayne Shmel
This is a kit bash of a Baby Bertha that transforms a mild mannered rocket into mean, green, flying machine--the BioHazard. Modifications: One challenge was the tight fit of three 18mm motor mount tubes inside the BT-60 body tube. The 3 tubes were glued together and the inside "hole" was ...
- Modification Sky Goon By Stan McKiernan
This is a Goonie of one my favorite classic boost gliders, the Sky Dart. The Sky Goon starts as a Baby Bertha and adds wings, stabilizer and engine pod. Modifications: The rear of the nose cone is removed, leaving about 1/2" of shoulder which is glued to the body. The engine mount is built ...
- Scratch Streamliner By Mark Van Luvender
I chose to build the Streamliner for this contest as it truly spoke to me as something I could do--that doesn't happen often. This rocket started out as an Estes Baby Bertha kit. In order to create the "Streamliner", I cut a wedge shaped section out of the body tube starting just below where ...
Related Products
Sponsored Ads
 |
 |