Brief:
T' Escape Velocity is a single stage, high power, dual or single deployment rocket for 38mm motors or 29mm with an adapter. Begad! Begad!

Construction:
T' Escape Velocity came with everythin' you could want for a HPR rocket and more. Well, blow me down! Avast! Blimey! Included were 1 pre-cut phenolic body tube, arrr, 1 phenolic payload tube, me bucko, ya bilge rat, fin can, payoad bay, 1 18" drogue parachute, arrr, shiver me timbers, matey, 1 36" main parachute, shiver me timbers, me bucko, 2 strap nylon shock cords, 2 parachute protectors, me hearties, arrr, 2 shock cord protectors, me hearties, Slimline motor retainer, ya bilge rat, Nose cone, me hearties, aluminum rail guides, and all necessary hardware. Blimey! All parts arrived in good condition. Begad!

I emailed Ed at Giant Leap on advice for how t' finish it and he recommended fiberglassin' it. Well, blow me down! I went with a 6ft section o' Aerosleeve's 2.5 inch sleeve. This be me first time glassin' an airframe and I be pleasantly surprised at how easy it was usin' a small paint roller, arrr, Great Plane's finishin' epoxy (picked up at a LHS), and t' Aerosleeve. Construction was fairly quick and straightforward. Avast! I used a Dremel cuttin' disc t' re-cut t' fin slot after applying the Aerosleeve and I used an X-Acto knife, me hearties, 150 grit sandpaper, ya bilge rat, shiver me timbers, and a level surface t' even out t' ends o' the airframe. Avast! Aye aye! T' 13 pages o' instructions had plenty o' pictures and detail t' make it clear even for t' first timer. Arrr! Begad!

T' only "gotcha" in t' instructions was t' method for fillin' t' gap betwixt t' fincan and the airframe. Blimey! T' fincan fits inside t' main airframe. Avast! When you epoxy in t' motor mount and fincan, thar are significant gaps betwixt t' airframe and t' fins. Blimey! T' instructions tell you t' mix up some 6-minute epoxy and mix in talcum powder until t' consistency is similar t' that o' cake frosting. Personally, arrr, I never could mix in enough talcum powder to get t' consistency right and have enough time left t' apply it t' t' airframe. Well, shiver me timbers, blow me down! Mine always was a bit too thin and it took me 3 attempts per fillet, matey, which was about 6 batches o' epoxy/talcum mix, t' get it right. Aye aye! Even then, matey, it took significant sandin' with a Dremel tool t' get t' final fillets t' look acceptable.

T' only area that I decided t' stray from t' instructions be t' electronics bay. Begad! T' method outlined in the instructions is a bit vague but sufficient. Begad! Well, me bucko, blow me down! I prefer a bay setup similar t' that o' t' LOC payload bays. Ahoy! Any method is good as long as it works for your altimeter. I used t' PerfectFlite MAWD with a 1/4 inch vent hole drilled into the payload bay from t' side. Aye aye! If you haven't done dual deployment before, then I recommend gettin' someone experienced to help you through t' setup o' t' electronics bay.

Finishing:
This bein' me first time fiberglassin' an airframe, ya bilge rat, I almost used an entire can o' KILZ primer t' smooth out the texture o' t' Aerosleeve. Well, blow me down! If you use an Aerosleeve on t' airframe, me hearties, arrr, I cannot overemphasize t' need t' sand well between coats. Ya scallywag! I made this mistake and probably added an ounce or two (or more) o' extra wieight in primer because I could nay get t' finish smooth. Begad! I literally spent hours and hours sandin' off t' extra coats o' unnecessary primer that I sprayed on. I found that t' KILZ primer available at Home Depot works well for this type o' application. Blimey!

T' kit came with a large decal, matey, however, me bucko, I opted nay t' use this as it would nay look well with me chosen color scheme. Avast, me proud beauty!

Construction Rating: 4 out o' 5

Flight:
Flight prep is fairly easy and with t' parachute and shock cord protectors, ya bilge rat, I didn't have t' worry about waddin' too much. Ahoy! T' Slimline retainer held t' motors in just fine.

T' first flight o' me Escape Velocity was on an Aerotech I357T-M. Ya scallywag! Avast! T' flight was wobbly off t' pad. This might have been due t' t' rail bein' a little loose at launch. Avast, me proud beauty! Aye aye! This was t' first flight o' me altimeter so I did use an ejection charge consistin' o' 1g o' BP and 2 Oxral E-matches. Well, blow me down! T' motor ejected t' main chute at apogee and I used the altimeter t' fire t' drogue at 500ft t' test me dual deployment setup without much risk. T' flight was t' 2632ft and landed a short walk away.

T' next flight was me L2 cert flight. Well, blow me down! I completed me L2 test, built t' J350W motor, loaded up t' rocket, and re-adjusted t' pad. Ahoy! T' manufacturer projected an altitude o' 5200 ft for a J350W and RockSim be about t' same. Instead o' a drogue, I hooked up about 20ft o' yellow caution tape. Ahoy! I gave a short countdown and whoa momma! The Escape Velocity ripped off t' pad with what sounded like a shotgun blast. T' takeoff was neck snappin' and perfectly straight. T' reflective finish allowed us t' see her all t' way up at apogee and on t' way back down. Well, blow me down! She landed about 100 yds away in t' middle o' t' field. Aye aye! Avast, me proud beauty! T' Perfectflite altimeter worked perfectly, shiver me timbers, ejectin' t' main chute at 500ft, ya bilge rat, and reportin' back an altitude o' 5961 ft.

Eager t' fly again, me bucko, I cleaned t' motor case, shiver me timbers, built t' I600R motor, me bucko, arrr, and prepped t' rocket in about 40 minutes. I put her back on t' pad, gave t' countdown, ya bilge rat, and oh boy! T' I600R motor put out a flame that be as long as the rocket. Avast, me proud beauty! Flight be again perfectly straight and totally neck snapping! Just like before, she came back down in the middle o' t' field and t' altimeter popped t' main at 500 ft. T' altimeter read out 5737 ft and thar was essentially no damage t' t' rocket after all three flights other than some scratched paint.

Recovery:
T' provided strap nylon shock cord and protector worked well. Avast! T' 36" chute is a good fit for this kit, although t' payload section gets very full on a loose pack o' this chute. Blimey! T' descent on t' 20ft streamer was just right for t' higher altitude flights. Avast! Any slower o' a descent and it might nay have landed in t' field. Arrr! Any faster and I would be worried about causin' a failure o' t' recovery system. Avast! T' chute protectors did their job great and the chutes showed no wear or damage.

Flight Rating: 5 out o' 5

Summary:
This is a great kit as it goes together smartly and is very tough when glassed with an Aerosleeve. Aye aye! Fin fillets and finishin' can be tedious and more time consumin' than expected. Arrr! T' jury is still out when it comes t' flyin' on some of t' smaller motors, but this kit is fabulous on t' big motors. She has t' performance o' a sports car, the bells and whistles o' a luxury car, and t' ruggedness o' a Hummer.

Overall Rating: 5 out o' 5