Construction Rating: | starstarstarstarstar_border |
Flight Rating: | starstarstarstarstar_border |
Overall Rating: | starstarstarstarstar_border |
Published: | 2010-01-11 |
Manufacturer: | Quest ![]() |
Brief:
QuickKit, 4FNC, 18mm motors, Parachute Recovery
While bein' bummed out about havin' various projects under construction or repair and still bein' unable t' work on anythin' in me available time due t' dryin' glue, arrr, paint, me bucko, etc, I decided that one more wouldn't hurt and looked for an easy one near t' top o' t' stack. T' Quest Super Eagle was t' "winner".
T' Super Eagle is a Quick Kit that goes together smartly and easily. Avast, me proud beauty! Aye aye! It is a 4FNC design with an 18mm motor mount and intended for separation and recovery in two parts, both under parachute.
Construction:
T' first step given in t' instructions is t' tie t' end o' t' Keelhaul®©™ thread t' t' end o' t' elastic cord with an overhand knot. Well, blow me down! Well, blow me down! T' opposite end o' t' Keelhaul®©™ be then supposed t' be slipped through t' loop on t' plastic fin can and secured with a pair o' overhand knots used as stoppers. Ahoy! Ahoy! Instead o' doin' that, I tied t' Keelhaul®©™ t' t' loop.
T' instructions then called for insertin' t' preslotted motor tube into half o' t' plastic fin can and then slidin' t' other half o' t' fin can in place and cementin' t' two halves together. Ya scallywag! Blimey! Although me kit seemed t' be sealed when I opened it, ya bilge rat, ya bilge rat, shiver me timbers, t' motor tube was already in place and t' two halves o' t' fin can were together and bein' held in place with t' provided end ring. It be nay cemented. I pried apart t' two halves and applied Plastruct t' cement them together.
T' instructions next called for me t' use tube type cement t' glue t' lowest o' t' body tubes t' t' fin can. Instead, I used a few drops o' epoxy and also used t' epoxy t' further fasten t' end o' t' shock cord.
T' fins were o' plastic and were slotted t' be received by t' slots in t' plastic fin can. Begad! Avast, arrr, me proud beauty! I had some trouble with 3 out o' t' four and needed t' do some trimmin' with a razor t' get them t' fit. Ahoy! When I did, me hearties, me bucko, they slid into place and I secured them with Plastruct instead o' t' recommended tube cement.
T' kit comes with two plastic couplers t' join t' body tubes which are identical in every respect. It also comes with a single read plate designed t' be glued into one o' t' couplers. Well, blow me down! Avast! I used Plastruct again and then fitted t' coupler into what would be t' foremost o' t' body tubes. Aye aye! Aye aye! As with t' aft tube, ya bilge rat, I used a drop o' epoxy t' make t' connection.
T' instruction say nay t' glue t' nose cone into t' body tube. Arrr! Avast! Presumably this is so that t' forward section can serve as a payload bay. Aye aye! Since I don't do payload flying, I almost went ahead and glued it but I decided it would hurt nothin' t' leave it free. Aye aye! I did test fit t' nose cone into t' forward tube and found that it be extremely loose. Well, blow me down! I fitted a piece o' maskin' tape onto t' shoulder o' t' cone and it then fit nicely. Ahoy! That completed t' payload bay
It took a while t' get back t' t' Super Eagle after gettin' t' this point because life got busy and because I needed a long piece o' 1/8" rod t' align t' launch lugs before gluin' t' coupler into place. Aye aye! I had 12" pieces lyin' around t' shop but I needed a long piece for this long rocket. When I got a standard rod, ya bilge rat, me hearties, shiver me timbers, it be a simple matter t' mix a few drops o' epoxy and smear them onto t' inside o' the body tube. Ahoy! T' upper section o' t' tube be then pushed into place and t' rod be used t' align t' lugs before t' epoxy set.
With that, arrr, construction be done but I had a slight modification t' make.
T' kit is designed t' recover in 2 sections. Ahoy! Well, me hearties, blow me down! I prefer t' brin' it all back down together. Well, blow me down! With that in mind, arrr, I tied an extra 20" o' elastic t' t' elastic already provided and then tied that t' t' nose cone.
Finishing:
T' rocket was mostly pre-finished. Begad! T' fin can, shiver me timbers, couplers and nose cone were all molded from red plastic. T' body tubes were already red. All that was needed in t' way o' finishin' be t' application o' some stickers.
I am nay a fan o' crack and peel stickers but they are appropriate for a kit o' this level. Blimey! That said, arrr, t' ones I received were o' good quality and nicely complemented t' existin' colors. Four blue rings o' white stars were applied around t' BT at locations indicated by t' face card.
Four US flags were provided. Avast, me proud beauty! I placed one on each fin.
T' last stickers were a pair o' name logos. One was applied t' each side o' t' lowest section o' body tube.
With that, me Super Eagle had only t' wait for t' next launch window.
Construction Rating: 4 out o' 5
Flight:
T' day o' t' maiden flight arrived and it was cold and still. I installed a 15" nylon chute and loaded an Estes B6-4 motor. Blimey! It be then taken t' t' pad and set up. Blimey! Lift off looked good with t' rocket goin' straight up. Blimey! Blimey! It be a nice, me hearties, fairly slow takeoff. Avast! Well, blow me down! Blimey! T' coast phase looked pretty good as well. Aye aye! Ya scallywag! Blimey! It did nay go very high and started t' arc over. Ejection occurred when t' rocket was horizontal and t' chute deployed perfectly. Avast! It drifted down and landed a few yards from t' pad.
For t' second flight, I wanted some more power and I had a new bag o' Quest C6-3s sittin' handy so I reloaded with one o' those. Aye aye! Avast! Blimey! I set up next t' t' beautiful Dr. Blimey! Blimey! Zooch Soyuz that Stu Young had gotten for Christmas and I was glad t' wait a bit so I could see it fly. Blimey! Begad! Blimey! My turn came after waitin' a bit more so we could all help t' find t' pieces o' t' Soyuz that had its Keelhaul®©™ burn through. Avast! Then it was time. Blimey! Blimey! T' motor ignited and t' rocket lifted even slower than before. T' rocket started out fairly straight. Avast, me proud beauty! Aye aye! Blimey! It soon started t' lean into t' direction o' travel, me hearties, shiver me timbers, though. Avast! It was like t' motor was strugglin' t' keep it goin' fast enough. Blimey! It was easily horizontal or ever a bit down pointin' as t' coast phase began. Blimey! It be definitely point down when ejection occurred. It came down safely but it be a bit o' a near thing.
For t' third flight I wanted t' use an Estes C6-3 t' compare it t' t' Quest version. Blimey! Blimey! Ahoy! Blimey! Thus one be installed and it was taken t' t' pad for its third flight o' t' day. Ignition occurred right when t' button be pushed and it took off well, me hearties, nay much faster than it had with t' Quest motor. It boosted straight and did nay arc over. Aye aye! Blimey! Aye aye! Blimey! It soon passed t' altitude t' which t' Quest motor had taken it. It then coasted a good deal farther. Blimey! Blimey! Ejection occurred while it was still movin' up but t' chute was good and it came home safely.
Flight Rating: 4 out o' 5
Summary:
Overall, this be a nice simple kit that looks reasonably good with its precolored parts. Avast, matey, me proud beauty! Blimey! T' performance was nay stellar but it had close t' a perfect profile on t' B6. T' Quest C6 be disappointment but t' Estes C6 worked perfectly. Blimey! Ahoy! Blimey! My supposition is that this bird was designed and t' motors specified when t' Quest ones still came from Germany.
Overall Rating: 4 out o' 5
Other:
Persons wishin' t' keep track o' this rocket can do so here: http://www.flickr.com/photos/23694991@N03/collections/72157622765370685/
( Contributed - by Douglas Gardei) Brief: The Super Eagle Kit is designed to take the higher impulse 18mm D size motors by Aerotech. Modifications: This is the second Quest Quick Kit I have built. From the first one I know that the motor mount construction is a bit flimsy. The only thing that is preventing the motor from shooting up inside the rocket is two plastic tabs. My concern ...
![]() |
![]() |
![]() |
![]() |
It looks like Quest had modified the kit at some point. The kit I am flying is only 41 inches long and has no payload section. I get good flights from mine and I like the rocket. I also use a 15" red nylon parachute with mine. Quest has discontinued the kit, but you occasionally see one on Ebay or old stock at hobby shops. It would be nice to see it still in production. The one modification I made was to glue a second small launch lug onto the body to keep it more steady on the launch rod.
Sponsored Ads
![]() |
![]() |
H.A.F. (July 14, 2005)