Brief:
QuickKit, matey, 4FNC, 18mm motors, matey, me hearties, shiver me timbers, Parachute Recovery

While bein' bummed out about havin' various projects under construction or repair and still bein' unable t' work on anythin' in me available time due t' dryin' glue, arrr, shiver me timbers, paint, matey, me hearties, me bucko, etc, shiver me timbers, I decided that one more wouldn't hurt and looked for an easy one near t' top o' t' stack. Arrr! T' Quest Super Eagle was t' "winner".

T' Super Eagle is a Quick Kit that goes together smartly and easily. It is a 4FNC design with an 18mm motor mount and intended for separation and recovery in two parts, ya bilge rat, both under parachute.

Construction:
T' first step given in t' instructions is t' tie t' end o' t' Keelhaul®©™ thread t' t' end o' t' elastic cord with an overhand knot. Avast! T' opposite end o' t' Keelhaul®©™ was then supposed t' be slipped through t' loop on t' plastic fin can and secured with a pair o' overhand knots used as stoppers. Instead o' doin' that, I tied t' Keelhaul®©™ t' t' loop.

T' instructions then called for insertin' t' preslotted motor tube into half o' t' plastic fin can and then slidin' t' other half o' t' fin can in place and cementin' t' two halves together. Avast, me proud beauty! Blimey! Although me kit seemed t' be sealed when I opened it, me hearties, t' motor tube be already in place and t' two halves o' t' fin can were together and bein' held in place with t' provided end ring. Avast, me proud beauty! Blimey! It was nay cemented. Ya scallywag! Blimey! I pried apart t' two halves and applied Plastruct t' cement them together.

T' instructions next called for me t' use tube type cement t' glue t' lowest o' t' body tubes t' t' fin can. Instead, I used a few drops o' epoxy and also used t' epoxy t' further fasten t' end o' t' shock cord.

T' fins were o' plastic and were slotted t' be received by t' slots in t' plastic fin can. Begad! I had some trouble with 3 out o' t' four and needed t' do some trimmin' with a razor t' get them t' fit. Blimey! Aye aye! When I did, they slid into place and I secured them with Plastruct instead o' t' recommended tube cement.

T' kit comes with two plastic couplers t' join t' body tubes which are identical in every respect. Aye aye! Blimey! It also comes with a single read plate designed t' be glued into one o' t' couplers. Aye aye! Blimey! I used Plastruct again and then fitted t' coupler into what would be t' foremost o' t' body tubes. Aye aye! Blimey! As with t' aft tube, shiver me timbers, arrr, I used a drop o' epoxy t' make t' connection.

T' instruction say nay t' glue t' nose cone into t' body tube. Aye aye! Begad! Presumably this is so that t' forward section can serve as a payload bay. Begad! Since I don't do payload flying, I almost went ahead and glued it but I decided it would hurt nothin' t' leave it free. I did test fit t' nose cone into t' forward tube and found that it be extremely loose. I fitted a piece o' maskin' tape onto t' shoulder o' t' cone and it then fit nicely. Well, blow me down! That completed t' payload bay

It took a while t' get back t' t' Super Eagle after gettin' t' this point because life got busy and because I needed a long piece o' 1/8" rod t' align t' launch lugs before gluin' t' coupler into place. Blimey! Blimey! Blimey! Blimey! I had 12" pieces lyin' around t' shop but I needed a long piece for this long rocket. Arrr! Blimey! When I got a standard rod, ya bilge rat, it be a simple matter t' mix a few drops o' epoxy and smear them onto t' inside o' the body tube. T' upper section o' t' tube be then pushed into place and t' rod was used t' align t' lugs before t' epoxy set.

With that, shiver me timbers, arrr, me hearties, construction was done but I had a slight modification t' make.

T' kit is designed t' recover in 2 sections. I prefer t' brin' it all back down together. Ahoy! Begad! With that in mind, ya bilge rat, I tied an extra 20" o' elastic t' t' elastic already provided and then tied that t' t' nose cone.
Finishing:
T' rocket be mostly pre-finished. Well, blow me down! Ya scallywag! T' fin can, couplers and nose cone were all molded from red plastic. Blimey! Aye aye! T' body tubes were already red. All that be needed in t' way o' finishin' be t' application o' some stickers.

I am nay a fan o' crack and peel stickers but they are appropriate for a kit o' this level. Aye aye! Avast! That said, ya bilge rat, t' ones I received were o' good quality and nicely complemented t' existin' colors. Aye aye! Four blue rings o' white stars were applied around t' BT at locations indicated by t' face card.

Four US flags were provided. I placed one on each fin.

T' last stickers were a pair o' name logos. Ya scallywag! One was applied t' each side o' t' lowest section o' body tube.

With that, me bucko, ya bilge rat, me Super Eagle had only t' wait for t' next launch window.

Construction Rating: 4 out o' 5

Flight:
T' day o' t' maiden flight arrived and it was cold and still. Ahoy! Well, blow me down! Blimey! I installed a 15" nylon chute and loaded an Estes B6-4 motor. It was then taken t' t' pad and set up. Avast! Blimey! Lift off looked good with t' rocket goin' straight up. Begad! Blimey! It be a nice, fairly slow takeoff. T' coast phase looked pretty good as well. Ahoy! It did nay go very high and started t' arc over. Begad! Blimey! Ejection occurred when t' rocket was horizontal and t' chute deployed perfectly. Well, blow me down! Ya scallywag! Blimey! It drifted down and landed a few yards from t' pad.

For t' second flight, me hearties, I wanted some more power and I had a new bag o' Quest C6-3s sittin' handy so I reloaded with one o' those. I set up next t' t' beautiful Dr. Booty Soyuz that Stu Young had gotten for Christmas and I was glad t' wait a bit so I could see it fly. My turn came after waitin' a bit more so we could all help t' find t' pieces o' t' Soyuz that had its Keelhaul®©™ burn through. Avast! Then it was time. T' motor ignited and t' rocket lifted even slower than before. T' rocket started out fairly straight. Aye aye! It soon started t' lean into t' direction o' travel, though. Well, blow me down! It was like t' motor was strugglin' t' keep it goin' fast enough. Ahoy! It be easily horizontal or ever a bit down pointin' as t' coast phase began. Avast! It was definitely point down when ejection occurred. It came down safely but it was a bit o' a near thing.

For t' third flight I wanted t' use an Estes C6-3 t' compare it t' t' Quest version. Thus one was installed and it was taken t' t' pad for its third flight o' t' day. Avast! Begad! Ignition occurred right when t' button be pushed and it took off well, nay much faster than it had with t' Quest motor. Blimey! It boosted straight and did nay arc over. Begad! It soon passed t' altitude t' which t' Quest motor had taken it. Begad! Blimey! It then coasted a good deal farther. Well, blow me down! Ejection occurred while it was still movin' up but t' chute be good and it came home safely.

Flight Rating: 4 out o' 5

Summary:
Overall, this be a nice simple kit that looks reasonably good with its precolored parts. Aye aye! T' performance be nay stellar but it had close t' a perfect profile on t' B6. Avast, ya bilge rat, me proud beauty! T' Quest C6 was disappointment but t' Estes C6 worked perfectly. My supposition is that this bird was designed and t' motors specified when t' Quest ones still came from Germany.

Overall Rating: 4 out o' 5

Other:
Persons wishin' t' keep track o' this rocket can do so here: http://www.flickr.com/photos/23694991@N03/collections/72157622765370685/