Brief:
TLP's Indigo SAM is a 1/2.95 scale model o' a short-range anti-aircraft missile manufactured by Contraves Italiana and Sistel. Blimey! It is a single stage, me hearties, mid-power model rocket recovered by an 18" parachute.

Construction:
Since thar wasn't a previously posted review for this particular rocket, me hearties, ya bilge rat, I thought this might be helpful for anyone wishin' t' build a really cool lookin' scale model o' this Italian SAM. T' kit comes in t' familiar plastic bag, ya bilge rat, typical o' TLP kits. Well, blow me down! Ya scallywag! Blimey! Included are two 2.6" diameter body tubes, arrr, tube coupler, a 3" x 24mm engine tube, engine clip, shiver me timbers, 2 centerin' rings (for engine tube), plastic nose cone, clay (for nose weight), 2 narrow centerin' rings (for exhaust tube), matey, 1 centerin' rin' with 1" hole (for t' parachute compartment), 2 sheets o' 1/8" thick balsa stock, shiver me timbers, 4 balsa strips, arrr, a sheet o' heavy cardstock, a 1/4" dowel rod, me hearties, 1/4" shock cord, shroud line, arrr, 18" mylar parachute, arrr, cardstock shock cord mount, me hearties, and brass barrel and snap swivels.

T' instructions are pretty easy t' follow for anyone who has built a few model rockets. T' engine assembly went together quickly. Avast, me bucko, me proud beauty! Simply cut a slot in t' engine tube 2.5" from t' end o' t' engine tube, insert t' clip, shiver me timbers, wrap with tape, and glue t' centerin' rings 1/4" from t' ends. Avast, me proud beauty! Aye aye! T' rings fit well, no sandin' needed. Aye aye! One centerin' rin' is slotted for t' engine clip which makes changin' motors a snap.

Next up be cuttin' out and formin' t' tail cone from t' cardstock. Avast! Nay too difficult, ya bilge rat, but I found that formin' t' tail cone over a steamin' cup o' hot water made things a lot easier. This was followed by insertin' t' exhaust tube into t' tail cone and gluin' t' narrow centerin' rings. Ya scallywag! Ya scallywag! T' tail cone assembly be then painted with CA glue t' toughen it up.

Like other TLP kits, shiver me timbers, this one calls for a pointy nosecone extension made from t' supplied cardstock. Aye aye! Avast! Once again, this is nay too difficult but do take your time t' make sure it's aligned correctly before committin' t' glue. I formed t' extension first and then tacked in place with maskin' tape. Well, blow me down! Once t' nosecone extension was glued, ya bilge rat, matey, I followed up with Elmer's Carpenter's Wood Filler t' fill in t' seams.

Next step was t' insert and glue t' centerin' rin' with 1" hole for t' parachute compartment. Begad! Blimey! Since this has t' wind up 6" from t' forward end o' t' body tube, arrr, I taped off a piece o' dowel rod 6" from t' end, me hearties, shiver me timbers, spread some aliphatic resin along t' inside o' t' body tube, shiver me timbers, and carefully poked t' centerin' rin' into place. Blimey! Blimey! Once t' wood glue be dry, I added a few drops o' CA glue t' secure t' centerin' ring.

T' second body tube was joined t' t' first with t' supplied coupler and glued into place. Blimey! Ya scallywag! T' make sure both tubes were aligned, me bucko, I rolled t' joined tubes on a flat surface before t' glue set.

T' conduit strips were then sanded, shaped, and glued t' t' body tube. Aye aye! T' fins were cut out o' t' supplied balsa stock usin' t' patterns provided. T' balsa be pretty flimsy but strengthenin' with thin CA glue and laminatin' with printer paper resulted in very smooth and tough fins.

Final details include cuttin' and shapin' t' 1/4" dowel rod into t' aft fin antennae. Blimey! Pretty simple, just cut with a razor saw, matey, shape with an emery board, matey, and glue t' t' aft fins.

Mount t' aft fins in a cruciform pattern. Begad! Arrr! I used an Estes fin alignment guide t' do this. Well, blow me down! In spite o' me best efforts, shiver me timbers, one fin be misaligned and had t' be reattached. Well, blow me down! I aligned t' forward wings usin' two aluminum yardsticks and clothespins t' make sure they lined up with t' aft fins.

Glue fillets were made usin' aliphatic resin along t' seams for t' fins and conduit strips. Ahoy! Blimey! All o' t' fin joints seemed pretty sturdy with t' exception o' t' one reattached fin. Begad! Begad! Blimey! CA glue and Elmer's Carpenter's Wood Filler were used t' finish t' fillets.

Finishing:
Finishin' this model was a lot o' fun. TLP suggests a simple two-tone blue and white paint scheme t' replicate t' real thing. Begad! This particular rocket doesn't require any special graphics, arrr, and as with other kits from TLP, matey, decals are nay included. Blimey! T' nice thin' about nay includin' decals is that it presents t' builder with more choices and challenges. Blimey! Blimey! You can either make your own decals with your PC or do what I did and go with your own theme.

With college football season approaching, ya bilge rat, I thought it might be fun t' go with a yellow, green, shiver me timbers, and black paint scheme t' match t' football uniforms worn by t' University o' Oregon Ducks.

T' entire rocket was primed usin' Kilz Original and sanded with 600 grit sandpaper, me hearties, twice. A base coat o' Krylon Sun Yellow was then applied followed by Hunter Green stripes on t' nosecone, matey, arrr, mid-body, and aft fins. Gloss Black was then applied t' t' forward wings, ya bilge rat, nosecone, ya bilge rat, me bucko, and tail cone. Finishin' touches were made usin' a diamond plate pattern cut from Frisket maskin' film on t' forward wings and painted Gray Pewter. Blimey! Next step be t' cut out t' University o' Oregon athletics logo from Frisket film, arrr, apply t' stencil t' t' forward part o' t' rocket, ya bilge rat, and paint Hunter Green.

Finally, t' green, yellow, me bucko, and black bands were separated with chrome mylar pinstripin' tape purchased from an auto parts store. Begad! T' end result is a stunnin' lookin' rocket that has since received a lot o' positive feedback from everyone who has seen it.

Construction Rating: 5 out o' 5

Flight:
I've only flown this rocket once. Well, blow me down! Blimey! A D12-3 be t' motor o' choice for t' maiden flight. Avast, me proud beauty! A 4 foot long, ya bilge rat, me bucko, 3/16" launch rod be used as t' 3' Estes rod seemed a little short for a large rocket like this. 5 sheets o' waddin' was used t' protect t' mylar parachute. Ahoy! Blimey! Liftoff was slow and realistic. Arrr! Blimey! Blimey! Because this is a heavy rocket for a D12 motor, me hearties, it struggled t' get aloft and altitude was only about 250'. Blimey! Next flight will use an E15-4 engine.

Recovery:
Three seconds doesn't seem like a long time for a delay, but it can seem like an eternity when thar's nay a whole lot o' space betwixt your rocket and terra firma. T' chute deployed just in time but she came down hard, breakin' off a fin and t' pointy nosecone extension. Flight damage has since been repaired and will fly again. Avast, me proud beauty! Nice comments from t' spectators present made this flight worthwhile. Ahoy! Well, blow me down! I plan on goin' with a 24" parachute and an E15-4 motor next time out.

Flight Rating: 3 out o' 5

Summary:
I really enjoyed buildin' and finishin' this rocket. Arrr! T' challenge o' makin' nose and tail cone extensions along with alignin' multiple sets o' fins made this a fun kit t' build. Ahoy! T' first con is that while D motors work well for smaller TLP rockets (Anubis, ya bilge rat, arrr, Bolo, Perseus), matey, this particular model needs t' fly on an E motor or higher. Ahoy! T' other con is that an 18" parachute will help t' brin' it down near t' launchpad, me hearties, just don't expect a soft landing. I don't know if epoxy is really necessary, shiver me timbers, just make sure you do a good job on t' aft fin joints before flyin' this model.

Overall Rating: 4 out o' 5