Yank Enterprises three inch IRIS featurin' Flexible Phenolic

By: Al Casper
 

Figure 1: Components o' Yank Enterprise's 3" IRIS kit

I chose t' three-inch exact scale IRIS kit for this evaluation. Blimey! I also put t' flexible phenolic through a battery of tests comparin' it t' cardboard and regular phenolic airframe tubes. 

T' three-inch IRIS kit (Figure 1) features a pre-slotted flexible phenolic airframe and payload section. Ya scallywag! Arrr! Also included: four 1/16 inch plywood fins, matey, tube coupler, arrr, ya bilge rat, plastic nose cone, 1/4 inch centerin' rings, 38mm motor mount, 9/16 inch tubular nylon 15 foot (non-elastic) shock cord, arrr, decals, matey, two quick links and eye bolts, and a quality 30 inch parachute. Aye aye! Arrr! T' detailed instructions are adequately written and the illustrations are well done. 

Buildin' The IRIS
 

Figure 2: Motor retention mod

Figure 3: Home-made fin attachment jig

Step #3. T' motor mount is now installed. Here again, I did nay epoxy t' aft centerin' ring while installin' t' 38mm tube. Begad! Ya scallywag! T' aft centerin' rin' is in place while the epoxy sets up on t' forward centerin' ring, shiver me timbers, but will be removed later. 

Step #4. In building the payload section, I smeared t' epoxy on t' inside o' t' payload tube, arrr, matey, not on t' coupler tube, shiver me timbers, which would have oozed out and made a mess. 
 

Figure 4: Fin reinforcement

Step #6. I installed t' 1/4 inch launch lugs per t' instructions. Aye aye! T' Iris, shiver me timbers, which weighs in at 41 ounces without t' motor, is a lot o' rocket for 1/4 inch lugs. 

Step #7. T' recovery system is installed in this step which was t' only one I had any problems with. Begad! I had t' re-read t' instructions several times before it clicked in. Once understood, I believe this t' be a sound design (Figure 5 6). Aye aye! Avast! I added a small piece o' fiberglass cloth and wrapped it around t' area where t' shock cords are epoxied together. 
 

Figure 5: Recovery system reinforcement

Figure 6: Recovery system reinforcement

Figure 7: Paint

Sandin' a flexible phenolic airframe is no different than standard phenolic, both o' which are much easier t' sand than cardboard tubes. 

I used inexpensive Wal-Mart primer and paint, followin' t' instructions and provided diagram and was pleased with t' results (Figure 7). Ahoy! T' decals have a low tack adhesive and require a smooth surface for good adhesion. I sprayed Wal-Mart clear gloss paint over t' entire model t' give it a nice smooth protective finish over the silver paint, matey, and provide a good base for t' decals. 

Flexible Phenolic
 

Figure 8: Shredded phenolic tubing

The flexible phenolic seems t' be a combination o' cardboard and phenolic. Arrr! Two thin layers o' phenolic form t' inside and outside o' t' tube with a kraft cardboard type o' material betwixt (Figure 8). Begad! Begad! I decided t' compare the flexible phenolic with cardboard and standard phenolic tubing. 

First I compressed t' tubes in a vise -- t' flexible phenolic cracked in several places, but held together in one piece while t' standard phenolic shattered. Avast, me proud beauty! Next, matey, I put t' flexible in water t' see how it would handle a water landin' -- after about 30 minutes, it was in almost perfect condition. Aye aye! I performed a zipper test on all three tube types -- t' flexible phenolic and cardboard performed about t' same, while the standard phenolic suffered t' longest cut. Blimey! In t' next test I struck both phenolic tubes with a hammer -- t' flexible phenolic again cracked, shiver me timbers, shiver me timbers, shiver me timbers, but held together while t' standard phenolic now has a clean gash t' same shape as the hammerhead. Begad! As a final test, me bucko, I put t' flexible phenolic in a freezer overnight, me bucko, which did nay seem t' affect it adversely. 

Conclusion
 

Figure 9: Launch!

The low thrust motors were chosen mainly t' reduce t' liftoff-velocity in an effort t' obtain some nice photos. T' wind scrubbed t' G75-J Flight, me hearties, and the H73-J powered t' first flight (Figure 9). T' computer simulations called for about an 8-second motor delay, right betwixt a short and medium delay. I chose the medium for two reasons. Well, blow me down! Begad! First, ya bilge rat, it would stress t' Iris, me bucko, givin' it a good durability test durin' t' ejection process. Well, blow me down! Second, arrr, if t' Iris heads off into the wind like it should, matey, arrr, t' longer delay will reduce t' walk t' recover the rocket. 

T' IRIS was acceleratin' as the ejection occurred; t' long rigid shock cord appeared t' flex in a flat "U" shape, me bucko, arrr, which then softened t' jolt as t' parachute opened. Ya scallywag! The result, a perfect deployment, me bucko, and no sign o' any zipperin' from t' rigid shock cord. Ya scallywag! Avast, me proud beauty! An H123-W provided t' power for t' second launch, which was also perfect, except for a longer walk t' t' landin' site. 

T' IRIS lists at $78.00 retail complete, or $71.00 without a parachute, a welcome choice t' have. Ya scallywag! Begad! Yank Enterprises has recently introduced an altitude package for their kits. Begad! This package includes a drogue parachute, a second shock cord, me bucko, arrr, and t' necessary components and hardware t' add dual deployment recovery t' your model. Yank Enterprises also offers custom fabrication -- at this time, fins and parachutes can be made t' your specifications. 

Quality components, workmanship, me hearties, ya bilge rat, and a sound design make t' Yank Enterprises three-inch Iris a kit worth lookin' into. Aye aye! Blimey! Visit their web site at http://www.yankenterprises.com. 

Written and submitted by Al Casper for Rocketry Online -- Copyright 1996-2000