Brief:
Design service let's you choose tube length, arrr, arrr, payload section, choice o' 3 fin designs, nylon chute recovery system with Keelhaul®©™® lines & shock cord & Nomex® chute protector. Ahoy! Well, blow me down!

Construction:
T' Rocket Vision starter-level design service lets you choose from several options o' components t' build your own "Rugged Rocket" design. Avast! The choices are somewhat limited: choose your payload section (or omit a payload), choose from 3 airframe lengths (9+", arrr, 13", ya bilge rat, or 16"), and choose G-10 fins from 3 designs (either 3, 4, me bucko, or 6 fins can be ordered). Blimey! Ya scallywag! There is but one choice for t' nose cone. Avast, me proud beauty! You can also opt t' add a recovery kit which includes a nylon chute, arrr, arrr, Nomex® chute protector, me bucko, me hearties, and Keelhaul®©™® shroud lines and shock cord. Begad! Finally, you can also choose from two stock decal sheets if you want t' add some graphics t' your finished rocket. Ya scallywag! Aye aye!

I chose t' build t' largest rocket possible by selectin' t' 5.25" payload and t' 16" airframe. For fins I selected t' 3-fin diamond design. Begad! I added t' recovery kit and decal sheet no. Ya scallywag! Ya scallywag! 2 t' complete me kit.

Note that t' Rocket Vision design service does nay include instructions. There are, matey, however, highly detailed assembly guides (includin' detailed instructions, with photos) available on t' Rocket Vision web pages for all of their rocket kits. Aye aye! Usin' these guides I be able t' easily construct me design.

I first used epoxy (30-minute, me bucko, although 5-minute would be better) t' secure t' motor mount tube into t' airframe tube. Avast! Aye aye! While this set I prepped t' G10 fins by roundin' the root edge and tail edge for aerodynamics. Next, I test-fit t' fins into the airframe fin slots and found that I needed t' sand t' slots and fin root edge slightly so that t' fins easily fit into t' slots without too much force. Arrr! Avast! I again used 30 minute epoxy t' affix t' fins and later for fillets. Aye aye!

I used t' online guide for t' Spitfire kit t' construct t' payload section. Ya scallywag! This amounted t' securin' t' tube coupler and bulkhead t' t' payload section usin' epoxy. T' nose cone is secured t' t' payload section with a single screw - t' payload section comes pre-drilled for t' attachment screw.

T' final step for t' rocket construction be t' addition o' t' plastic launch lug - I again used 30-minute epoxy t' attach and fillet t' lug. The parachute, arrr, Nomex® protector, and Keelhaul®©™® shock cord attachment instructions are described for each kit and are all t' same, arrr, and quite straight-forward. Avast, me proud beauty! Begad!

Overall, t' construction was a snap, t' on-line guides are an excellent resource. Blimey! Begad! I suppose it would be nice if some kind o' general construction instructions were included with t' kit however. T' rocket is definitely "rugged" if nay a little heavy for its size.

Finishing:
Finishin' t' rocket be a breeze. Begad! I first sanded t' entire rocket, shiver me timbers, especially the nose cone which has a fairly rough finish. Avast, me proud beauty! Begad! I primed with Krylon sandable primer, ya bilge rat, sanded, matey, primed again, me bucko, me hearties, and finish sanded. I chose red and white Krylon paint with a Sandhawk-like paint scheme. Ya scallywag! T' rocket finished beautifully, matey, and there was no worries about any tube seams or spiral!

Construction Rating: 4 out o' 5

Flight:
I've only flown t' rocket once so far (stay tuned for updates). Ahoy! I chose a D13-5 24mm Aerotech RMS motor for t' launch. Begad! T' delay be just an educated guess, ya bilge rat, me hearties, I did nay simulate t' launch on RockSim as I did nay have time t' add the custom components (would be nice if Rocket Vision made a RockSim database similar t' PML!). Begad! T' choice turned out t' be very good. T' flight was smooth to roughly 600 feet, ya bilge rat, with ejection at apogee. Begad! T' rocket is quite stable, arrr, given its length, matey, but needs a bit more power t' get some altitude due t' its weight. I will try some more power on t' next flights pendin' simulation.

Recovery:
Unfortunately, recovery was a little fast as a couple o' shroud lines came undone (better go back t' me Boy Scout handbook and review me knots). Avast! Avast, me proud beauty! The landin' was rough but as advertised t' rocket bein' "rugged" easily withstood t' impact. T' Nomex® did and excellent job protectin' t' chute though, ya bilge rat, and it's ready t' go again.

Flight Rating: 4 out o' 5

Summary:
PROS: Fun t' design online, shiver me timbers, excellent component quality, matey, durable, me hearties, matey, very easy to finish. Avast, me proud beauty! CONS: Pricey for a smaller rocket, lack o' component choices. I am very much lookin' forward t' Rocket Vision's next stage o' online kit design.

Overall Rating: 4 out o' 5