| Construction Rating: | starstarstarstarstar |
| Flight Rating: | starstarstarstarstar |
| Overall Rating: | starstarstarstarstar |
Brief
For those o' you still followin' my Goonyness this be Baby Bertha kit bash #11. Again this is nay a kit review o' t' original but another o' me many kit bashes. All fin patterns and decals came from http://www.spacemodeling.org/JimZ/est0806.htm. Ya scallywag! T' major difference again bein' that mine is a Goony version o' t' USAF Pegasus (Estes Kit #0806). It will also have an 18mm motor mount instead o' t' 13mm o' t' original due t' bein' built from a Baby Bertha kit. Avast, me proud beauty! I'm doin' this review mainly because no one has done one for this rocket yet.
Components
As stated this is a kit bash so t' main components came from a Baby Bertha Kit. Ya scallywag! As a result this will be a BT-60 based rocket instead o' a BT-20 tube as t' original was.
From Baby Bertha kit:
- 1- BT-60 Body Tube
- 1- PNC-60 Nose Cone
- 1- Launch Lug
- 1- Engine Hook
- 1- Shock Cord
- 1- Assembled 12" Parachute (transparent orange plastic)
- 1- Mylar Retainer
- 1- Green Engine Block
- 1- Blue Engine Mount Tube
- 1- Centerin' Rin' Card
Decals and wood from t' Baby Bertha were placed in with me salvage materials and new wood was used t' make all necessary parts for this build. Avast! Blimey! T' decals were printed on standard printer paper. T' only other parts that I needed that did nay come with t' kit were a 3/4" end o' a tooth pick for t' antenna mast and betwixt 1/8-1/4oz. Ahoy! Blimey! Well, blow me down! Blimey! o' clay for nose weight.
Construction
Construction be done as per instructions with t' only Con: havin' been t' tracin' and cuttin' o' all t' parts from new balsa. Aye aye! On t' Pro: side, shiver me timbers, It was t' engine pod assembly that made me build this rocket in t' first place. Begad! Aye aye! It be another technique for buildin' scoops that I wanted t' try and I love t' end result.
Wings are only taped on so I can get an idea o' what it will look like.
Bottom view (hope I remember t' glue on a launch lug).
Finishing
Finishin' be done in my usual method of priming entire rocket with Rust-Oleum 2x Primmer, a light sanding, matey, followed by more priming, and then two coats o' Krylon White Gloss. Once dry rocket was then masked off and t' Krylon Grey Gloss applied t' nose and win' tips. Avast! Decals were then printed out and clear coated with Krylon Clear Gloss. Begad! After they dried they were cut out and attached with a glue stick. Begad! After that entire rocket got two coats o' clear gloss t' seal on t' decals.
USGF Goonasus Glamour shots
Flight
Maiden flight took place on 06-20-10 at a S.M.A.S.H. Avast, me proud beauty! Begad! club launch on an ever popular Estes B6-4 and was a beautiful flight. Rocket left t' pad in a big hurry and climbed straight up toward t' clouds. Aye aye! Arrr! No Cons:
Recovery
Parachute be deployed shortly after apogee with a nice gentle decent. Aye aye! Upon recovery found that t' left win' tip was damaged. It was cracked and leanin' at an angle. Begad! Ya scallywag! Super glued it back in place. Avast! This be t' only Con: as I suspect that this will happen again as they are t' first thin' t' hit t' ground.
Summary
This was another fun build and another learning experience for me. Aye aye! Well, blow me down! Each o' these Goonies were built so I could learn different techniques and ways o' buildin' model rockets with scoops, ya bilge rat, air intakes, tubes and so forth. Anythin' other than your standard 3 or 4FN style rocket.
#Related Reviews
- Clone Cloud Hopper By Steve Lindeman
Cloud Hopper was my second Goonybird clone that I built by kit bashing an Estes Baby Bertha and as a result has an 18mm motor mount instead of the 13mm that the original Cloud Hopper had. Components Components used for this build were one Estes Baby Berha Kit (1261) and the plans ...
- Clone Missile Toe By Steve Lindeman
Missile Toe was number three in my line of cloned Goonybirds that was built by kit bashing another Baby Bertha kit. As such the plans and decals were downloaded from Ye Old Rocket Plans (http://plans.rocketshoppe.com/estes/est0854/est0854.htm) and used for construction guide. ...
- Clone Sky Shriek By Steve Lindeman
The Sky Shriek was clone number four of the original Goonybirds that I built. And as such is another kit bashed Baby Bertha . The plans were downloaded from http://plans.rocketshoppe.com/estes/est0855/est0855.htm . I then followed these to build the Sky Shriek with the ...
- Clone X-15 By Steve Lindeman
In all fairness I can't do a brief description on this kit as there is a small story behind it. As is normal for me this is not an actual review of the Estes NASA X-15 (0889) [1988-1989]. It is a kit bashed, clone by transition. I came about the idea of doing the X-15 as the G-15 after ...
- Clone Zoom Broom By Steve Lindeman
Zoom Broom was the 1st of my Goonybird clones modified for 18mm motors as a result of being kit bashed from a Baby Bertha. Components Starting with a Baby Bertha kit (EST 1261) that I purchaced at my local Hobby Lobby, all components except the balsa wood and decals were used to ...
- Excelsior Rocketry Der Goony Max By Bill Eichelberger
Der Goony Max is an inspired bit of lunacy from Excelsior Rocketry, and I guess depending on where you stand on the Goony issue, this series is either genius or a waste of a good Baby Bertha. Speaking as the one-time-owner of an original Goonybird Cloudhopper, I happen to fall on the genius ...
- Kit Bash GoonyHawk By Steve Lindeman
Here I go again. For those of you that have followed my Goonyness this was Baby Bertha kit bash #14. Again this is not a kit review of the original Estes Hawkeye (Kit #0873) [1986-1996] It is another of my many kit bashes. All ...
- Kit Bash GoonAries SST By Steve Lindeman
Here I go again. For those of you that have followed my Goonyness this was Baby Bertha kit bash #10. Again this is not a kit review of the original Estes Aries SST (Kit #1927) [1983-1984]. It is another of my many kit bashes. ...
- Kit Bash Goony Target Drone By Steve Lindeman
Lucky or unlucky? For those of you that have followed my Goonyness this was Baby Bertha kit bash #13. As such I wanted to play it a little safer with this one so I choose a simpler design. Again this is not a kit review of the original Estes ...
- Kit Bash Goonymarc By Steve Lindeman
The Goonymarc was number eight in my line of modified Baby Bertha kit bashes. I started with the plans from Jim Z's for the Estes kit #654 with the thought of building the glider version of the Bomarc but ended up with the parachute version (kit #657). All templates and decals for this build ...
- Kit Bash NASA Goonasus By Steve Lindeman
One again this is not a kit review of the original NASA Pegasus (Estes Kit #1376) [1982-1986] but another of my many Baby Bertha kit bashes (#12 for those following my Goonyness). All fin patterns and decals came from http://plans.rocketshoppe.com/estes/est1376 ...
- Kit Bash Snarky Jr. By Steve Lindeman
The Snarky Jr. (a.k.a. Goony Shark) was kit bash #6 in what was to become a long list of Baby Bertha's that I converted into various Goony Birds and such. The inspiration for this one of course came from my DynaStar's - Snarky and the fact that I wanted to be able to fly it in the smaller ...
- Kit Bash Streamliner By Steve Lindeman
The Streamliner was the fifth in a series of Baby Bertha kit bashes that I did while building my Goonybird fleet. The first four kits were used to make four of the original Goonybirds from Estes but now it was time for somthing a little different. I remember seeing this model in a&n ...
- Kit Bash USSF Goonyflash By Steve Lindeman
For those of you following my Goonyness this is Baby Bertha kit bash #9. So OK this is not a kit review so much as it's actually another of my kit bashes. All fin patterns and decals came from http://www.spacemodeling.org/JimZ/estes/est1909.pdf . The main ...
- Mo' Skeeter By Chris Gonnerman
This is my Mo' Skeeter, a 320% upscale of the classic Estes Mosquito . It's a rear-ejection model, which avoids the visible nose cone line that most Mosquito upscales suffer from. Components This rocket consists of a Baby Bertha cone , 6" of BT-60, 6" of BT-20, two 20-60 ...
- Modification Baffled-Boat-Tailed-Bigger-Baby-Bertha By Mike Goss
It all started one day after I opened a Baby Bertha kit and found that the motor mount had the wrong size adaptor rings. The rings were for a BT-50 and not a BT-20. I thought about replacing the rings with a correct set, but then the creative juices started to flow, what could I do with this ...
- Modification BioHazard By Dwayne Shmel
This is a kit bash of a Baby Bertha that transforms a mild mannered rocket into mean, green, flying machine--the BioHazard. Modifications: One challenge was the tight fit of three 18mm motor mount tubes inside the BT-60 body tube. The 3 tubes were glued together and the inside "hole" was ...
- Modification Sky Goon By Stan McKiernan
This is a Goonie of one my favorite classic boost gliders, the Sky Dart. The Sky Goon starts as a Baby Bertha and adds wings, stabilizer and engine pod. Modifications: The rear of the nose cone is removed, leaving about 1/2" of shoulder which is glued to the body. The engine mount is built ...
- Scratch Streamliner By Mark Van Luvender
I chose to build the Streamliner for this contest as it truly spoke to me as something I could do--that doesn't happen often. This rocket started out as an Estes Baby Bertha kit. In order to create the "Streamliner", I cut a wedge shaped section out of the body tube starting just below where ...
Related Products
Sponsored Ads
 |
 |