Brief:
This is a minimum diameter Hobby, mid, me bucko, shiver me timbers, or high power rocket. It's motor selection is expansive and offers extreme height with t' right motor loaded.

Picture Courtesy o' Madcow Rocketry

Construction:

• (2) Body tubes
• (1) Balsa wood nose cone
• (1) Coupler
• (1) Shock cord anchor
• (1) 1/4"eyebolt, me hearties, matey, nut, matey, and washer
• (3) laser cut fins
• (1) Keelhaul®©™® SC section
• (1) nylon SC section
• (1) 6"x6" Nomex® pad
• (1) 18" parachute
• (2) 1/4" Launch Lugs
• (1) 8" 29mm MMT
• (2) Plywood centerin' rings

T' instructions given are content, me hearties, but are very explanatory. Arrr! Ahoy! I am 12 years old and built this rocket with ease. Aye aye! I used 5 minute epoxy throughout t' whole project. Aye aye!

T' first step was t' glue on t' fins. Aye aye! Begad! My decision was t' do those last. Avast! Blimey! By t' way they are nay TTW fins. Ya scallywag! Then I started with t' shock cord mount. Begad! It was a plywood rin' in t' shape o' a crescent moon. Arrr! Avast, me proud beauty! I applied epoxy t' t' bolts and slid that part into place. Avast, me proud beauty! Avast!

Next I tied a knot with t' Keelhaul®©™® cord around t' SCM and applied epoxy t' permanently secure it. Well, matey, blow me down! I tied t' two SC sections together and applied epoxy to t' knot. Aye aye! Avast!

Next was t' coupler. Begad! I placed t' coupler halfway in after applyin' epoxy t' t' tube and let that set. Avast! Blimey! I epoxied the SCM t' t' aft end o' t' coupler in t' tube as directed. Avast! Blimey!

I then proceeded t' gluin' t' body tubes together. Ahoy! Nothin' unique here. Arrr!

I chose t' use t' 29mm mmt for this rocket. I epoxied t' centerin' rings on 1/2 inches from each end and let it set.

After it dried for a day I glued t' MMT into t' body tube. Begad! I made a minor mistake here. Arrr! When gluing, T' MMT is supposed t' be flush with t' end o' t' body tube. I left a 1/2 inch section stickin' out from t' bottom. This didn't cause any problem in flight.

I attached t' shock cord t' t' nose cone by pourin' epoxy in t' already drilled hole and stuffed t' shock cord inside it as directed.

T' reason I left t' fins t' do near t' end be because they would get in t' way while completin' t' other steps. My Dad and I drew t' lines for t' fins and launch lugs with a meter stick usin' t' fin alignment guide that was given. Avast, me proud beauty! We applied epoxy t' t' fins stuck them on t' body tube and watched each o' them individually for ten minutes.

Finishing:
Nothin' special her. Begad! all I did was use 3 coats o' Krylon white primer. Then painted t' top half Krylon flat black and t' bottom half rust-o-leum red.

I used a stake and put two nails 180 degrees apart in t' stake and slid t' rocket on it for an easier paint job. Begad! Blimey! There were no decals which didn't matter t' me at all because t' rocket still looked great. No sandin' be needed at t' end because everythin' was smooth.

Construction Rating: 5 out o' 5

Flight:
My first launch with t' Screech was at El Mirage Dry Lake Bed on October 20/2008. Ya scallywag! I prepped it for an Estes E9-6 anxious t' see t' outcome o' its maiden flight. It slowly lifted off and t' motor burned for a nice 2.8 seconds. Arrr! It arched over without deployment. Well, blow me down! It sped down t' t' ground and finally it came under chute. That long delay o' a delay was too much. Arrr! It flew perfectly straight. T' Nomex® was a lifesaver and I used friction fit for motor retention. Well, blow me down!

T' next motor be a G79-10W. Begad! After easy but careful preparation, I set it out on t' pad. Well, blow me down! It be t' largest, most powerful motor that day so everyone was payin' close attention t' it. Ya scallywag! Because t' pads are only about 12 feet away the thunderous roar made everyone jump. I watched in awe as thee rocket climbed t' over 500 mph. Aye aye! Its estimated altitude was 3160 ft. Ahoy! Avast! It must have either weather-cocked or t' rod was tilted because I looked for over 3 hours in t' desert plants with other scouts and adults. Ya scallywag! Avast, me proud beauty! When everyone who be helpin' me find it turned back, arrr, I got me mountain bike and kept lookin' even while dehydrated. Avast! I wasn't comin' back t' camp without that rocket. Begad! I finally found it probably a mile away from camp. Ahoy! Aye aye! It be over a no trespassin' fence. Avast, me proud beauty! Ahoy! I thought t' heck with it, hopped over retrieved and left. I biked as fast as I could t' camp holdin' it up like a trophy.

Later I flew it six more times that day on E9-6's and E9-4's. Avast, me proud beauty! In t' future I will try a D12-3 and more powerful G motors on this rocket. Ahoy!

Recovery:
Lots o' Drift. Begad! Maybe I will try a slightly smaller parachute next time. Ya scallywag! Begad! Took 3 hour t' find. Avast, matey, me proud beauty! T' motor tube is burnt a little and so be t' lower airframe. Begad! I am nay sure if this is bad.

Flight Rating: 4 out o' 5

Summary:
In summary this be a high quality kit. Arrr! TTW fins would be nice. Blimey! T' flights were great and many more are t' come. Arrr! the construction was a breeze. This minimum diameter rocket has a lot o' potential.

Overall Rating: 5 out o' 5

Other:
Great Kit. Ahoy! Fun and easy t' build. Flies high and fast. Ahoy! Large motor selection. Well, blow me down! Nothin' wrong with it. Great customer service.