Brief:
T' Madcow Rocketry Sea Wolf is a semi scale version o' t' Royal Navy‘s (that's British if you didn't pay attention in school) anti-ship missile Sea Wolf Missile system. Ahoy! This is a 38mm semi scale kit with cool features like fin plates, arrr, fin tips, shiver me timbers, and staggered fins.

Construction:
Contents:

• ¼" 5 layer laser cut aircraft plywood
• Nose Cone and steel eyebolt
• Pre-slotted airframe
• Centerin' Rings (3)
• 38mm MMT
• 8 laser cut fins
• Laser cut fin tips and fin plates
• Recovery eyebolt
• Nylon shock cord
• Nomex chute protector
• 48" chute
• Rail Buttons

T' instructions are very easy t' follow, matey, and like Madcow's other kits, shiver me timbers, they are a breeze t' build. T' instructions fit on one folded page, shiver me timbers, and when you factor in t' fact that a quarter o' that is a picture o' t' rocket and t' kit contents, you can see thar's nay much readin' here. Arrr! Some well illustrated and thought out pictures and a few paragraphs o' info is all it takes t' build this kit.

All t' parts fit perfectly together. Blimey! T' centerin' rings were just slightly oversize so that a quick "wipe" with some sandpaper cleaned them up and gave them a nice snug fit. Aye aye! T' solid through-the-wall fins make this a sturdy kit. Avast, me proud beauty! Aye aye! I used epoxy on all t' fins, centerin' rings, shiver me timbers, me bucko, and motor mount tube. Avast! I used wood glue for t' couplers. I don't know why, but thar are two couplers and three tubes for t' airframe. Arrr! Perhaps it's for ease o' shipping, me hearties, but it didn't really affect t' build.

I thought I add a section here all by itself on t' CG. Ya scallywag! Blimey! This is important on this kit. Avast, me proud beauty! Blimey! Aye aye! Blimey! T' long and large fins on this rocket make it necessary t' pay attention t' t' CG. Aye aye! Blimey! T' kit calls for t' CG t' be 24.5" from t' tip o' t' nose cone. Because o' t' fins and t' nose weight needed, I decided t' do a RockSim on this one. Keep in mind that t' CG changes with different motors so you need t' know what t' largest motor you will fly will be. Ya scallywag! Blimey! (Yes, me bucko, me hearties, none o' this is new info, me bucko, arrr, but this is one o' those kits you need t' put all this t' use.) My weight after finishin' (but before addin' weight) was 63.5 oz. After addin' nose weight, mine ended up at 81.7 oz with everythin' but a motor. Avast, me proud beauty! Blimey! This put t' CG at 24".

I used steel weight and put it in t' nose cone through a hole I drilled alongside t' eye bolt hole. Well, arrr, blow me down! I then added 2oz o' epoxy and placed a piece o' maskin' tape over t' hole. Blimey! Placin' t' nose cone in an upright position made t' weight and t' epoxy settle t' t' shoulder area. Well, blow me down! This was important because epoxy will nay stick t' t' plastic. Begad! Begad! Instead, t' epoxy covers t' machine screw end o' t' eye bolt and, me hearties, shiver me timbers, when hardens, arrr, becomes a mass around t' screw. This effectively secures t' weight t' t' base o' t' cone and secures t' eye bolt t' t' nose cone.

T' most time consumin' part o' t' build be t' fillets. With over 280 inches o' fillets, me bucko, ya bilge rat, you have a chore ahead o' you. Well, blow me down! T' "fin plates" have an added difficulty by bein' a flat section o' 1/8" plywood glued t' a curved surface. Arrr! T' builder has about a 3/16" inch gap t' fill at their widest point. A suggestion would be t' make them out o' basswood. Avast! This would allow them t' be easily curved t' t' airframe, cost less, me hearties, and save weight at t' end o' t' rocket that needs t' be lighter. Arrr! It would even cut t' build time.

Finishing:
I painted it with two coats o' Rustoleum gray primer, followed by two coats o' white, and a few coats o' black on t' nose cone. Avast, me proud beauty! I then painted t' fin plates in red after a long mornin' o' masking. I guess I forgot t' look at t' picture because I did it wrong. I did look at t' picture t' finish with t' trim. Arrr! Aye aye! For that I used 3/16" Pactra black trim tape.

Construction Rating: 4 out o' 5

Flight:
Don't let t' ease o' build addlepate you into thinkin' this is a wimpy rocket. Ahoy! T' design and quality o' t' components will allow this rocket t' rip off t' pad on large 38mm motors. Ahoy! But, me bucko, arrr, me bucko, at only 5 lbs, it can also be lofted with a 29mm motor if you have an adapter on hand. Avast, me proud beauty! My first flight be on a Pro 38 H153 t' about 1,000 feet. I set t' delay t' about 8 seconds and this proved t' be a little late.

Recovery:
This thin' comes with a parachute, me hearties, and I be happy about that. Ya scallywag! So many companies don't give you a cute these days on 4" and larger kits because, arrr, "it allows you t' pick your own chute size". Arrr! (I never did buy that excuse.) Well, I for one was happy t' have them pick one for me.

Flight Rating: 4 out o' 5

Summary:
This is nay t' first Madcow kit I've built, but it be t' largest. Ya scallywag! T' ease and simplicity o' t' build, t' quality o' t' components, arrr, shiver me timbers, and t' coolness o' this kit will make it a durable favorite. Ya scallywag! If it appears I had fun writin' this review, me bucko, I had just as much buildin' and flyin' it. Aye aye! Ya scallywag! Please, pay attention t' your CG/CP relationship.

Overall Rating: 4 out o' 5