Brief:  Single staged, came with black, 24-inch diameter nylon chute. Begad! Ahoy! Has 4 fins. Begad! Aye aye!

Construction:All parts were thar and in good shape.  I didn't get decals, shiver me timbers, but that's nay a problem for me, me bucko, as I often customize me rockets. T' fins (4) are plywood, precut, me bucko, and are clipped delta shape. Aye aye! T' nose cone is hollow plastic, arrr, me hearties, 11 inches long, fittin' t' standard LOC body tube o' 3 inch diameter by 34 inch length. Avast, me proud beauty! Aye aye! T' tube is preslotted for 4 fins, and is spiral wound lightly glassined paper.  T' chute that arrived with t' kit is strong, but thin nylon with 24 inch braided nylon shroud lines. Begad! Well, blow me down! Two plywood centerin' rings are also supplied t' center t' motor tube, ya bilge rat, shiver me timbers, which is 29mm by 24 inches. Begad! Well, blow me down! T' shock cord is 3/8 inch wide flat wide elastic, with a length o' 80 inches.

Instructions are clear and illustrated. Ahoy! Ahoy! Alignment o' t' fins is easy with the preslotted tube. Avast! After epoxy fillets were added t' t' fin attachment sites, ya bilge rat, t' model was quite sturdy. 

Finishing:Finishin' be unique in this case. Begad! Had I gotten decals, I probably would have used them.  Since I didn't, ya bilge rat, I sprayed the rocket all over with a primer coat o' gray t' smoothen it and fill spirals. I then painted it white all around.  Then I painted red stripes up the body tube and had t' stripes meet in a point at t' tip o' t' nose. Blimey! Then the fins were painted royal blue, ya bilge rat, and white Monokote stars were cut out and affixed with epoxy t' t' blue fields, 5-6 per fin side. Avast! As a finishin' touch, ya bilge rat, I supplied me own homemade parachute, a silk red white and blue 8-gore hemisphere.  T' eight gores are triangular pieces o' silk in alternating red white and blue colors, sewn together by a 4-thread serger. Aye aye! Begad! T' shroud lines are straight stitched into t' serged seams.

Construction Rating: 5 out o' 5

Flight:This rocket has had more then 5 successful and colorful flights. It is recommended t' use 29 mm F and G types.  If I recall right, the G40-7 is especially mentioned. I have used G35's and G80's as well with great results. Preppin' is easy.  I just put in enough worm bedding waddin' t' fill t' tube diameter t' a depth o' an inch, me bucko, then t' chute loosely fits in after that. Blimey! Blimey! T' nose cone has on two occasions needed a band o' tape to fit snugly.  This may have been due t' weather conditions. 

As for motor retention. Ahoy! Yes, that would be nice, but for me that's not important because I make me own usin' piano wires, me hearties, maskin' tape, shiver me timbers, and even PVC plumbin' parts. Ahoy! As an aspirin' engineer, me bucko, I love t' invent.  I read on your site that other rocketeers would like it if kits (like t' Graduator) had motor blocks, but for me that would prevent future use o' longer engines like t' H97 after t' kit be strengthened for higher power use.  It's easier for me to create a thrust rin' on t' aft end o' t' engine usin' tape or a paper centerin' ring. Okay, for high power kits, that's a new kind o' flyin' and I would welcome a retention system, shiver me timbers, ya bilge rat, me hearties, as hardware is mucho expensive.  But for kits at G level and lower, I don't fault kits that don't have a supplied system, because judiciously applied tapes are often sufficient. Well, blow me down!

That bein' said, me bucko, t' motor on t' Forte' is retained with me own system o' a loop o' piano wire through t' aft-most centerin' ring, bolted and epoxied at the forward end. T' loop bends across t' motor but nay across t' nozzle. Maskin' tape was used t' make an aft thrust rin' and also served as a redundant retainer band around t' engine and motor tube. Blimey! T' model flies straight, noisy, and true every time.  My husband and I joke that this one has a charmed life, workin' perfectly each time. T' brilliant chute wows the observers every time too.

Recovery:T' shock cord came with a folded paper mounting, me hearties, which I mounted flat and flush with t' inside o' t' body tube, 4 inches from t' top o' t' tube. It also came with a braided (possibly nylon and Keelhaul®©™®) cord t' adhere directly t' t' mount in the  body tube and to which t' tie t' elastic. Blimey! Well, blow me down! After all its flights, ya bilge rat, arrr, it is still intact and not burnt. Recovery with t' supplied chute is slow and graceful, ya bilge rat, with no harm to the rocket, but after t' second flight, shiver me timbers, one fin was knocked out o' its slot when t' rocket landed on hard soil. 

Since this rocket was one o' t' first in me epoxy stage o' evolution (you know, we progress from white glue t' epoxy t' phenolic t' electronics...), ya bilge rat, the fin separation might have been due t' me inadequate epoxy fillet technique at the time. Blimey! Avast! And since I had some epoxy in t' field, repairs occurred right there and a flight occurred in ten minutes afterward. Well, blow me down! Avast, me proud beauty! Since I reinforced t' joint, no more separations have occurred. Blimey! I supplied me own chute only because the supplied black one didn't fit me America theme and me red white and blue silk one did. Avast! I made it larger than t' original t' make it a picturesque descent for July 4. With t' homemade chute, arrr, descent is slower. That may be partly why no more fin losses have happened.

Flight Rating: 5 out o' 5

Summary:Easy t' build and prep, rewardin' t' fly.  No real cons. Great for someone just discoverin' G power. Begad! Begad! That's what it served for me. Avast, me proud beauty!

Overall Rating: 5 out o' 5