I have seen many different versions o' this idea on t' Internet and decided t' do one o' me own. Ya scallywag! I purchased t' large crayon bank from Toys-R-Us for around $6 or $7. Arrr! Ahoy! I chose red. Ahoy! T' tube is roughly 3 3/4 inches inner diameter and a little less than 3 ft long. Ahoy! I have sent for plans from a gentleman on Internet who has built several and has put together tip sheet and a large drawing. Ahoy! Looks good as a guide. Well, blow me down! I also have written several people that I met through t' RMR newsgroup. Blimey! I am gettin' a lot o' good info t' help me build mine. Ya scallywag! Avast! I am goin' t' go with t' 29mm motor mount. Aye aye! I am thinkin' I will use plexiglass for t' fins. Aye aye! I also bought some bright yellow nylon at cloth store t' make a chute. This is goin' t' be a fun project!

Here are t' basic parts o' me rocket centerin' rings, matey, engine tube (29mm), me hearties, arrr, Plexiglass fins, matey, (they are leanin' against t' body tube), Body tube (the cardboard portion o' crayon bank), matey, ya bilge rat, nose cone and aft end cap. Ahoy! T' aft plastic part o' t' crayon bank also serves as a centerin' rin' . Avast, me proud beauty! Ahoy! I put two centerin' rings inside body tube and t' engine tube will stick out t' back o' t' plastic cap. Ahoy! Ya scallywag! Notice t' friction rings that come on t' nose cone have been removed. Ya scallywag! Would be too tight if I did nay do this.

Below is a view durin' construction. You can see t' forward part o' t' forward centerin' ring. Avast, me proud beauty! A metal cable is attached t' a screw eye. Well, blow me down! Later I attached t' shock cord t' this cable.

As you can see below I installed a type o' baffle. Begad! This is about 5 or 6 inches from t' forward end o' t' rocket tube. This will help a little with nay burnin' t' chute but mainly it helps hold recovery gear in nose o' rocket t' help with Center o' Gravity. Ahoy! Ahoy! You will also notice t' cable stickin' beyond t' baffle.

And also a picture from t' aft end o' t' rocket lookin' at t' forward centerin' rin' and t' motor tube. Well, blow me down! Begad! You can see t' thrust rin' around motor tube. Begad! I used 1/4 inch hardboard for centerin' rings and for t' bulkhead in t' nose section. Begad! Begad! You can also see t' slots that I cut for t' thru t' wall mountin' o' t' fins.

February 20, me hearties, 1998

I have worked a little at a time now and have completed t' crayon rocket. Was nay too hard t' do. Well, blow me down! I did end up usin' 1/8 plexiglass for t' fins. I will be usin' a 29mm RMS system with this rocket. Avast, me proud beauty! Aye aye! I did use what is called on Internet "Kaplow Klips" t' secure t' engine in place. Ya scallywag! Ahoy! I think this will work very well as t' prevent a lost casing. I bought some non rip nylon at cloth store and some nylon twine t' make a 32 inch parachute. Avast, me proud beauty! It looks good. Avast, me proud beauty! I went with a round design. I sure hope it deploys. Ya scallywag! Begad! My rocket club has a launch tomorrow and will try it out then! Will be tryin' an G40-4 or somethin' close t' this. Ya scallywag! Ahoy! I sure hope this works! This will be first attempt at anythin' above Estes D size motor. Well, blow me down! Will update after tomorrow!

February 21, me bucko, 1998

Launched today on G64-4. It went up about 50 ft or so and went horizontal. Begad! Aye aye! T' nose cone also detached itself from t' bulkhead and shock cord. Begad! In talkin' t' several others I think a little nose weight is in order. It may have just been weather cockin' but it was a little unstable as well. Ahoy! Aye aye! Back t' t' drawin' board.

March 21,1998

Launched t' crayon again today on a G64-4. Was a great day for rocket launching. Begad! No wind at all. Arrr! Ahoy! T' rocket did very well went straight up, me bucko, arrr, deployed chute and nose cone stayed on end o' shockcord as advertised. Blimey! I did break a fin. Aye aye! It must have broken durin' flight as I saw it land and did nay find t' piece in t' area o' landing. Begad! Flew much more stable today. Aye aye! Begad! Will fix fin and get ready for next time.

July 5, 1998

I launched t' Crayon once again. Begad! G64-4 T' launch went very similar t' t' one on Feb 21st. Aye aye! Up strait about 50 feet then horizontal. Ahoy! Only difference this time is I had chute and body separation, OUCH!! T' chute came out while it was travelin' very fast horizontally. Ahoy! I saw t' body come down separate from chute and also t' nose cone separate from t' rest. Arrr! I went and got t' chute, then had t' go t' t' area where t' body and nose cone came down. Well, blow me down! I had t' look for about 20 minutes t' find t' body. Begad! (Grass is tall this time o' year) I looked for a long time but never did find t' nose cone. Blimey! Ahoy! Ho Hum... Aye aye! Blimey! oh well back t' t' drawin' board. Blimey! All fins broke off however t' body tube is in fair condition... Well, blow me down! Begad! This crayon could fly another day... Blimey! now where t' get another nose cone.........

February 15, 1999. Begad! Blimey!

I began work again on t' old crayon rocket. Aye aye! I have decided that t' plexiglass fins were a neat idea in theory but I am really gettin' tired o' replacin' them after every flight. Ya scallywag! Begad! Blimey! While lexan would probably work I have decided that some old scrap red oak will work nicely. Resewn t' about a 3/16 thickness will work nicely. Blimey! Blimey! I had t' order a new nose cone from Ralphco. Begad! Begad! Blimey! T' people thar were very friendly and accommodated me with a new nose cone and a couple more crayon banks through t' mail very reasonably priced. Ahoy! Begad! Blimey! At t' time I called them t' Toys-R-Us didn't have any in stock. Anyway I have modified t' bank as mentioned and I have also added some nose weight with clay and filled t' nose cone with that expandin' foam sealant that you can used for home insulating, t' hold clay in front o' nose cone. Ya scallywag! Looks like it will work well. Avast! Blimey! Will attempt another launch as soon as I can.