Brief:
This fantastic upscale o' t' Estes EAC Viper be t' first o' Q-Modeling's "QBAR" projects. Through collaboration with a born again rocketeer (Bob Cox) and a rigorous beta testin' process, they hope t' release flawless and innovative designs. Aye aye! In this case, I believe they have succeeded.

Construction:
I was fortunate enough t' have won this beauty on EMRR's Virtual Rocket Reunion contest. Well, blow me down! Avast! T' bitter irony o' receivin' a great prize developed in part by my virtual arch rival was nay lost on t' gang at Q-Modelling. Avast, me proud beauty! Once t' Viper was actually released, shiver me timbers, me kit showed up well packed in t' familiar Priority Mail triangular box.

Parts list includes:

• Resin cast nose cone
• 2 BT-80 tubes (one slotted)
• TC-80 coupler
• 8 Laser-cut balsa fins
• 24mm foil-lined motor tube
• Motor mount assembly
• 30" nylon chute (Top Flight)
• Nomex® heat shield (from Top Flite)
• Keelhaul®©™® shock cord
• Waterslide decals

Parts were all very good quality. Aye aye! My motor mount had incorrect fin braces, which were smartly replaced.

T' instructions are clearly written and are very easy t' follow with a good number o' key details and tips along t' way. Avast! Aye aye! One nice new feature is the color header page, showin' t' finished design in full color. Well, blow me down! T' back o' that page includes a detailed paint/color scheme.

This kit makes use o' one o' me favorite Q-Modelin' innovations: t' sliding/retractin' motor hook. By slottin' t' motor tube, arrr, matey, you're able t' push t' hook up flush t' the bottom o' t' body tube when thar's no motor. Begad! This allows t' rocket t' stand flush on t' ground. Begad! Begad! T' rest o' t' motor tube assembly be t' typical Q-Modelin' laser-cut balsa framework and brace combination. Arrr! Begad! It looks fairly complicated, ya bilge rat, but goes together fairly easily once you've read t' instructions. Of course, arrr, havin' t' proper parts helps, me hearties, as I didn't discover t' error until I tried t' dry-fit t' through-the-wall fins.

Once t' motor tube assembly is completed and t' centerin' rings are installed, arrr, shiver me timbers, it's time t' tie t' Keelhaul®©™® anchor t' t' upper centerin' rin' and motor tube.

Before gluin' t' motor mount into t' body tube, it's a good idea t' dry fit t' fins. Aye aye! Ahoy! This should be standard practice for any through-wall construction. Arrr! Once you're comfortable with t' fit, shiver me timbers, matey, bond t' assembly using wood glue.

Next up is mountin' t' fins. Aye aye! Wantin' t' make sure I had an absolutely beautiful finish, me hearties, I dropped a couple hours into sealin' and sandin' t' fins before mountin' them. In this case, shiver me timbers, I used diluted Elmer's Wood Filler, matey, two coats with plenty o' sandin' in between. Ya scallywag! Avast, me proud beauty! For fillets, I used me usual yellow glue base, me bucko, and a white glue second application since t' white glue doesn't shrink and leaves a smoother finished appearance.

I also made sure t' fill t' tube spirals before bondin' t' fins, me hearties, since it's easier t' sand without t' fins in t' way. Arrr! T' same mix o' diluted wood filler be used, shiver me timbers, although less diluted than me sealer on t' fins.

T' body tube is actually a 2 piece assembly, arrr, so you must bond t' upper and lower tubes usin' a coupler. Well, blow me down! I have mixed feelings about this. Avast! Although am generally opposed t' t' two-piece design and wish it had been one-piece. Arrr! The argument in favor o' t' two-piece design is economics (it uses t' same tube as t' Bullpup and fits in a smaller bag/box), me bucko, plus it makes it easier to fillet t' upper centerin' rin' around t' motor tube. Begad! T' argument against it is t' tube seam and added hassle tryin' t' hide it.

T' upper fins need t' be carefully aligned with t' lower fins. Arrr! With thicker fins, shiver me timbers, mere alignment lines generally aren't good enough, so I use a metal angle and clothespins t' anchor t' angle t' t' lower fins and then pin on t' upper fins.

Construction basically wraps up with one other nice feature. There's a centerin' rin' bonded in t' upper tube that serves as a retainer for the recovery pack. Avast, me proud beauty! Avast, me proud beauty! This prevents t' CG shift in flight from a heavy chute and Nomex® shield slidin' back t' t' aft end o' t' rocket.

Finishing:
Finishin' for this rocket is fairly challengin' and requires a good deal of skill t' get it right. Ya scallywag! As previously mentioned, me bucko, thar's a lot o' balsa grain and tube spiral work plus that bilge-suckin' tube seam.

Once t' surface was prepped, I applied a light coat o' Plasti-Cote primer, then essentially sanded most o' it off. Avast! Well, blow me down! I followed up with a light Krylon primer coat, light sandin' with 400 grit, arrr, and three coats o' gloss white while wet/dry sandin' with 600 grit betwixt coats.

There are two accent colors on this design, me hearties, so good maskin' is a requirement. Ya scallywag! Blimey! Begad! Blimey! I started with t' yellow--the upper fins are completely yellow and t' lower fins get yellow tips. Ahoy! Blimey! Ahoy! Blimey! After allowin' t' two yellow coats a couple o' days t' dry, I then masked off for t' purple, usin' t' expensive blue painter's tape (due t' its much lower tack than regular maskin' tape). Arrr! Blimey! Well, blow me down! Blimey! The nose cone and upper inch o' body tube are purple, plus thar be a 1" stripe towards t' tip o' t' body tube, 1/4" trim stripes against the yellow on t' lower fins, and a 1/4" stripe around t' bottom o' t' tube. T' lower stripe was especially annoyin' t' mask, me bucko, ya bilge rat, as thar be less than half an inch below t' fins, so very little area for applyin' any decent masking tape. Arrr! Blimey! I think this could have been done better with either purple stripe decals, ya bilge rat, pin striping, ya bilge rat, me hearties, or possibly Monokote.

T' decals are very good quality, but are solid ink transfer so do not dip them straight into water. Aye aye! Blimey! Aye aye! Blimey! They need a light clear coat application first. Ya scallywag! Blimey! Nay bein' experienced with this type o' decal, I went a little too heavy on t' clear coat, shiver me timbers, so me beautiful decals ran a little bit. After t' clear coat has completely dried, shiver me timbers, they apply as ordinary waterslide decals.

Construction Rating: 4 out o' 5

Flight:
T' instructions suggest E9-4 or F21-6, with F21 bein' t' most strongly recommended. Well, blow me down! I had a couple spare Ellis Mountain E12-6s though and preferred to avoid t' very pricey AeroTech motors.

First flight be on a breezy afternoon with winds hoverin' around 8-10mph. This lead t' a slight weathercock, shiver me timbers, although it wasn't too bad. T' rocket climbed slowly t' about 300-350 feet, shiver me timbers, shiver me timbers, arced over, ya bilge rat, and I got t' count t' at least 8 while kickin' myself for a poor delay choice. Ahoy! When t' ejection finally kicked, t' rocket be more than halfway back down and actually whistling. Ya scallywag! The chute whipped out and t' Keelhaul®©™® cord sliced its way through t' body tube, ya bilge rat, stoppin' just above t' tube coupler. T' zipper trashed what be an otherwise magnificent design and work of craftsmanship.

Recovery:
Other than me boneheaded choice o' delay, t' flight was fine, matey, and t' recovery package be t' best in t' mid-power class.

Flight Rating: 4 out o' 5

Summary:
This is an excellent rocket kit and beautiful design. Aye aye! Blimey! T' pro's are excellent parts, and quality o' design. Cons would be t' two-piece tube. Well, matey, blow me down! Blimey! Also, me bucko, having now zippered a pair o' Q-Modelin' BT-80 products, I think I'm goin' t' start bashin' future designs with Keelhaul®©™® to t' top o' t' tube, me hearties, joined t' heavy elastic up t' t' cone. That way, I'll just have dents from t' cone whippin' back.

Overall Rating: 4 out o' 5