Brief:
Part o' t' Shrox/Apogee Global Defense Series, this 2-stage missile is designed t' protect our nation's capitol from hostile aircraft, missiles, me bucko, (or alien craft?). Avast! It's small, matey, matey, light, and incredibly fast when flyin' on both stages, though works quite well on a single stage also.

Construction:Parts List

• 24mm nose cone
• BT-50 body tube 9.75" long (sustainer)
• BT-50 body tube 2.75" long (booster)
• BT-50 tube coupler
• (2) 18mm motor tubes (2.75")
• 13-18mm centerin' rin' (engine block)
• (4) 18-24mm centerin' rings
• 1/8" launch lug
• 3/32 balsa or basswood fin stock
• 2 x 36 Mylar streamer
• 36" Keelhaul®©™ shock cord (plan calls for 300#, I used 110#)
• Clay nose weight (about 0.5 oz)
• Decal sheet (can be downloaded from E-zine archives #83)

After downloadin' t' Rocksim file (and lookin' at t' pictures in t' E-zine), you're on your own figurin' out how t' build this, ya bilge rat, since thar are no instructions (RockSim is also available here on EMRR). Ya scallywag! Fortunately, matey, that's nay too dauntin' a task, me hearties, as t' design is comparable t' most skill level 2 modrocs. Avast, me proud beauty! I started with t' motor mount assemblies, gluin' t' engine block in one tube, and mountin' centerin' rings on each 18mm tube. Aye aye! Since this is a 2-stage, shiver me timbers, joined with a BT50 coupler, ya bilge rat, pay careful attention t' t' location o' t' centerin' rings in Rocksim so that t' two stages will join well. Well, blow me down! After t' motor mounts have set, shiver me timbers, they are glued into t' body tubes along with t' tube coupler.

I printed out t' fin templates from Rocksim, ya bilge rat, and cut them from basswood, figurin' t' thrust from a 2-stage might put a bit o' strain on balsa (though FinsSim, arrr, an add-on t' Rocksim, indicates this would be no problem). Arrr! Ya scallywag! Tack t' fins on at 120 degree angles (I've found t' Estes tube markin' tool set t' be t' best $8 I've spent on this hobby), and apply fillets o' wood glue. Install t' shock cord/streamer, and t' rocket is nearly finished.

Note: t' clay nose weight - it was nay referenced on t' parts list in t' E-zine, shiver me timbers, though is included in t' Rocksim file. Well, blow me down! Without this nose weight, me bucko, this rocket is probably nay stable, and this could be an easily overlooked detail.

Finishing:
Two coats o' primer and two coats o' glossy white, shiver me timbers, arrr, followed by a coat o' light gray on t' booster, me bucko, and you're ready for decals. Arrr! I printed t' decals with me inkjet on Avery clear decal stock, though this is a fairly opaque finish, ya bilge rat, and I'd recommend findin' a better printer source, matey, possibly goin' t' t' expense o' water-slide decals. Also, dependin' on your field conditions, you might consider paintin' t' booster a bright red or orange, ya bilge rat, arrr, t' stand out more in taller grass.

Construction Rating: 4 out o' 5

Flight:
There were no recommended motors in t' E-zine or Rocksim file, arrr, me hearties, so I tried a few combinations in Rocksim and decided t' go with a C6-0 booster and A8-3 sustainer (I would have preferred a B boost, but didn't have any at t' time). Ahoy! Blimey! Field conditions were favorable for high altitude - 85 degrees and 5 mph winds, ya bilge rat, matey, and our club uses a field large enough t' handle most HPR motors.

I used t' full 0.75 ounce o' nose weight called out in Rocksim, shiver me timbers, and t' rocket was a bit over-stable, anglin' into t' light winds. Aye aye! Blimey! Both stages lit, ya bilge rat, and ejection on a 3-second delay be at least a couple seconds early, ya bilge rat, me bucko, even factorin' in t' weathercock. Avast, me proud beauty! Blimey! Begad! Blimey! T' nose cone separated, shiver me timbers, though this was from a weak shock cord mount, ya bilge rat, matey, nay due t' t' fact that I went with 110# Keelhaul®©™® instead o' 300#.

I recovered all components, me bucko, and after some minor repairs and removal o' about 0.25 ounces o' clay, shiver me timbers, flew again on C6-0/B6-6. T' flight be much better, shiver me timbers, ya bilge rat, screamin' out o' sight on a straight trajectory. Arrr! Apogee was beyond me eyesight, though t' 6-second delay was a much better choice.

Recovery:
Pro's

• Terrific altitude from t' 2-stage design

Con's

• A little tricky t' get t' right amount o' nose weight

Flight Rating: 4 out o' 5

Summary:
Overall, this is a very nice 2-stage design, me hearties, especially given t' price (free download). If you're new t' Rocksim, it's also a good design t' work with t' learn t' choose t' proper motor(s) and fine-tune t' CG/CP relationship.

Overall Rating: 4 out o' 5