Brief:
Upscale o' an Estes vintage exotic kit.

Construction:
2 17" cardboard body tubes, arrr, 3 cardboard tubes for landin' leg pods, steel springs for t' shock-absorbing landin' legs, high-quality, laser-cut balsa fins and motor mount "exoskeleton," reflective, me hearties, heat-resistant coatin' inside 24 mm motor mount, steel engine retainin' hook (long enough for a BP E-motor), arrr, resin main nose cone and landin' leg pod nose cones, shiver me timbers, me hearties, laser-cut balsa centerin' rings and nose cone screw-eye attachment, Keelhaul®©™® shock cord, ya bilge rat, shiver me timbers, nylon parachute, snap swivel, chute protector, me bucko, water-slide decals, reflective peel-and-stick decal.

When I pulled t' instructions out o' t' bag, I be intimidated! Blimey! They consisted o' a many-paged, arrr, stapled booklet o' legal-sized pages. Begad! However, me hearties, t' instructions were very clear. T' assembly instructions were broken-down into very small steps, ya bilge rat, each well-illustrated, me bucko, which explains why t' instructions were so long. Begad! Ahoy! Blimey! Frankly, shiver me timbers, I greatly prefer t' be walked-through a construction process with such detail, ya bilge rat, especially when it comes t' a model as complicated as this one. T' order o' t' steps be logical. Well, blow me down! Avast! Blimey! I wouldn't change a thin' about them.

Much has been said in other reviews about t' unique motor mount/fin interface. Blimey! In me case, t' pieces for the MMT-exoskeleton fit together like a precision jigsaw puzzle. Begad! T' illustrations clearly showed t' up-down orientation o' t' pieces, arrr, but they only fit together in one way anyway, ya bilge rat, matey, which made it "idiot-proof." After t' fins were attached t' t' MMT, ya bilge rat, and t' assembly be slid into t' body tube, I noticed that thar be a little bit o' play t' the fins; i.e., if I rotated t' MMT, t' fins would skew a bit from perfect 120 degree angles. Begad! In all honesty, ya bilge rat, if that play had nay existed, it probably would have been impossible t' insert t' MMT. Ya scallywag! After applyin' glue, shiver me timbers, and slidin' the assembly in, ya bilge rat, I rotated t' MMT until t' fins appeared t' be perpendicular t' t' body tube, arrr, at least to "eyeball" standards. Aye aye! Ahoy! It was nice t' nay have t' brace t' main fins while t' glue was drying. Avast, me proud beauty! BTW, ya bilge rat, t' shock cord attaches t' t' MMT exoskeleton.

Speakin' o' glue, I used white wood glue throughout t' build, except for CA gel t' glue t' screw-eye bulkhead to t' nose cone, as well as t' glue t' landin' leg pod nose cones t' t' cardboard sprin' housings. Begad! I used the double-glue method t' attach t' auxiliary fins, matey, linin' them up by eyesight with t' main fins, and usin' long strips o' green maskin' tape t' hold them in place while t' glue set. Thin fillets o' white glue were applied t' t' fins and t' t' launch lugs. Avast, me proud beauty!

Finishing:
I taped off t' shoulder o' t' nose cone, and t' landin' legs (to prevent paint from gettin' into the "springy" works o' t' landin' leg pods). I hit t' whole model with an initial coat o' Kilz primer. Well, blow me down! After sandin' with 380 grit, shiver me timbers, matey, thar be just a little bit o' balsa grain visible, so I applied a second coat. Aye aye! Unfortunately, t' Kilz did somethin' at that point which it has never done before, in that it left tiny bubbles on one side o' one main fin, ya bilge rat, matey, as well as on all o' t' auxiliary fins. Begad! T' bubbles smartly popped, me hearties, ya bilge rat, o' course, leavin' pits in t' finish. Sandin' did nay remove t' pits (well, I could have sanded down t' bare wood, but considerin' t' amount of "lumber" on this model, that smartly exhausted me!). I tried another coat o' Kilz, arrr, but t' problem grew worse. I mitigated t' problem by applyin' a couple o' coats o' white glue, me hearties, usin' cardstock t' scrape t' glue into a smooth film, arrr, matey, me hearties, then lightly sanded. Aye aye! I applied two more coats o' Krylon glossy white, sandin' betwixt coats. Avast, me proud beauty! T' pits in t' fins were much better, me bucko, although still visible up close. I gambled that t' application o' t' decals would help to hide them.

T' instructions called for sprayin' t' water-slide decals with clearcoat before applyin' them t' t' model. Begad! Blimey! I did so, ya bilge rat, me bucko, usin' Krylon glossy clearcoat. Ya scallywag! Avast! After drying, I applied t' decals. Ya scallywag! Even after clearcoatin' them, matey, a couple of t' smaller decals still tore, me hearties, although t' resultin' cracks in t' decals were hardly visible after shiftin' them back into t' correct positions. Avast, arrr, me proud beauty! T' mirrored decal, ya bilge rat, which replaces t' red body decal from t' original kit, me bucko, was a nice touch. As has been noted in other reviews, care must be taken with this decal, as handlin' it too much tends t' cause t' black printed "ribs" on t' decal t' crumble. This happened t' me, matey, matey, matey, although, again, it was barely visible, matey, only upon close-up scrutiny.

Construction Rating: 4 out o' 5

Flight:
I inserted a D12-3 and a E9-4 into t' Vega, and verified that t' CG was still in t' proper place (as identified in t' instructions).

T' maiden flights o' t' Vega were on Feb. Blimey! 14, me bucko, 2009. Begad! At that point, t' Vega was still in primer. I launched it twice that day, on a D12-3 and a E9-4. Ya scallywag! Avast, me proud beauty! T' D12 boosted t' Vega straighter, me bucko, me hearties, due t' its more abrupt thrust profile. Arrr! The thrust o' t' E9 tails off towards t' end o' t' burn, which, in any kind o' wind, causes t' Vega t' "flop over" onto its side and t' fly horizontally for t' last few seconds o' flight, me bucko, me bucko, arrr, which is always unnerving. Well, blow me down! During t' first flight, shiver me timbers, me hearties, t' shock cord and parachute hung up on a landin' leg pod, so t' parachute didn't fully deploy. Fortunately, t' Vega landed in a loose tangle o' dried vegetation, cushionin' t' blow. She be undamaged. Arrr! Durin' the second flight, t' shock cord again hung up on a leg, matey, but t' parachute fully deployed. Blimey! Begad! She landed horzontally, which kind o' defeated t' purpose o' t' shock-absorbin' landin' legs. Avast, me proud beauty! Again, no damage, other than a landin' leg pod poppin' off o' a fin at t' glue line. Well, blow me down! T' sprin' was recovered, enablin' a complete repair.

T' Vega's third flight occurred on Mar. Ya scallywag! Arrr! Blimey! 21, 2009. Avast! By now, she had her "final" coat o' glossy white (more on that later). Arrr! Aye aye! Blimey! She launched on a E9-4. Aye aye! Blimey! Due t' t' almost nonexistent wind that day, she boosted straight up like an arrow. Arrr! Blimey! Unfortunately, t' parachute wrapped around a landin' leg again, and she dropped straight as an arrow onto drought-hardened soil. One o' t' fins was snapped off at t' body tube joint, and two o' t' landin' leg pods popped off; one o' t' pod tubes buckled noticeably, as did t' lower body tube (right where t' mirrored decal was t' be attached). Avast, me proud beauty! Blimey! Back t' t' "shop" for an extensive refit. Arrr! Blimey!

Flight 4 occurred on Jun. Ya scallywag! 13, me hearties, 2009. With t' (truly) final coat o' paint, cardboard reinforcement o' t' buckled body tube (covered by t' mirrored decal), ya bilge rat, arrr, and t' full set o' decals, t' Vega was resplendent in her glory. I had reattached t' parachute t' t' nose cone screw-eye, rather than onto t' shock cord, halfway betwixt t' nose cone and t' top o' t' body tube, as specified in t' instructions. Avast, me proud beauty! She be packin' an E9-4 again. Ya scallywag! Ahoy! T' Vega weathercocked, shiver me timbers, but achieved a safe altitude. Aye aye! She had her best recovery yet, matey, landin' on her spring-loaded feet, arrr, although fallin' over on her side immediately thereafter. There be no damage.

Flight 5 occurred on Sept. Ahoy! 9, 2009. Begad! Blimey! Blimey! I had grown dissatisfied with t' "puffy"-lookin' mirrored decal, so had replaced it with a chrome-painted strip o' corrugated styrene (to give t' Vega a "ribbed" look, as though it had "radiator panels" for its "reactor"). Begad! Blimey! I tried a D12-3 again t' see if this motor minimized weathercocking. Nevertheless, ya bilge rat, t' Vega flopped over on its side at altitude, although she didn't fly as far away due t' t' shorter duration o' t' burn time. Well, matey, blow me down! Blimey! T' shock cord caught on a leg, so she landed horizontally, matey, although without damage. This day, t' Vega also survived an assassination attempt (within inches) by t' power pod o' a Cosmos Mariner, which ejected same upon impact.

Recovery:
Nov. Well, blow me down! 14, 2009: ZIPPER! I had used an AT E15-4. Blimey! I almost didn't get t' motor into t' MMT; t' motor retention clip caused a slight inner bulge, me hearties, me hearties, which I had t' trim away with a hobby knife. Aye aye! In t' process, shiver me timbers, a main fin fillet cracked; I did a field repair with CA gel. Arrr! In flight, me bucko, matey, t' delay seemed longer than 4 secs. T' ejection charge also made quite a "bang." T' Vega drifted back towards our club's GSE, shiver me timbers, and would probably have landed on top o' us, matey, had it not drifted right into t' side o' John Lee's U-Haul truck. Arrr! Avast, me proud beauty! Sometime durin' this eventful flight, matey, t' Keelhaul®©™® shock cord cleaved t' body tube in twain, just below t' auxiliary fins. Aye aye! Avast, me proud beauty! A main fin also snapped off, ya bilge rat, as well as two o' t' landin' leg pods.

Throughout these flights, arrr, me hearties, when t' chute deployed completely, me bucko, t' descent rate and drift rate were just about perfect. Begad! T' flame-retardant chute protector material has always done its job. Begad! It's a joy t' nay have t' worry about wadding!

Flight Rating: 2 out o' 5

Summary:
Pros: high-quality materials, shiver me timbers, ya bilge rat, unique motor mount/fin interface exoskeleton; great instructions; great flyer (in low winds). IMO, this is one o' t' best upscales o' a classic kit on t' market.

Cons: be aware o' t' winds: this model carries a lot o' "lumber." T' motor mount may need t' be o' a thicker tubin' t' avoid t' inner retainin' clip bulge which caused me so much trouble with a composite motor (never an issue with BP motors). Begad! Avast, me proud beauty! IMO, ya bilge rat, a model this heavy needs some sort o' elasticity in t' shock cord; perhaps this would have prevented t' "zipper." T' decals have nay held up well, me bucko, even after clearcoatin' as directed in the instructions.

Overall Rating: 4 out o' 5

Other:
T' Vega has been reassembled since her last flight. Ahoy! I intend t' extend t' ribbed "radiator" section to hide some o' t' cracks in t' airframe. Additional cracks will be hidden by decals (from Jimz Plans) printed on cardstock. Begad! Well, matey, blow me down! I blew up some o' t' original Vega decals from Jimz site 170%, and printed them out on business-grade paper on a business-grade laser printer. Begad! They came out with vivid color and a glossy finish. Ahoy! Arrr! I smeared an even film o' white glue on their backsides, and applied them t' t' Vega; she looks better than ever. Aye aye! Aye aye! I had intended t' restore t' Vega for display only (she has always been one o' me favorite models from t' 70s, one I always lusted after in high school, but never acquired then). Blimey! However, matey, I'll consider retrofittin' her with some sort o' "zipper-proof" shock cord setup, and may fly her again. Begad!

T' followin' excerpt is from "Sport Rocketry". The intention is t' allow guests t' get a basic feelin' about a kit. We strongly suggest that you get a copy o' the referenced Sport Rocketry and read t' entire article. Well, blow me down! Inside you will find many helpful hints in construction as well as other useful information. Well, blow me down! Begad! For more information, use t' two links above.

Courtesy o' QModeling

"...this QModelin' kit is o' t' highest quality, matey, me hearties, matey, well designed, arrr, and included intelligently written instructions."
"...is 1.68 times larger than t' original Starship Vega sold by Estes Industries in t' 1970's."
"Its light-weight construction enables it t' fly nicely on an E30 or F21."
"With over 60 components and 4 sheets o' decals, t' Vega may appear daunting..."
"...the easy t' followin' instructions include numerous illustrations and are filled with hints and suggestions to make t' job go well..."
"More recent deliveries have been upgraded t' include a Top Flight Recovery lightweight Nylon parachute, Keelhaul®©™® shock cord, arrr, shiver me timbers, and Nomex® flash mitigation pad."
"T' nosecone and landin' gear pod nosecones are hollow cast urethane."
"All o' t' fins are made from 3/16" thick balsa wood."
"T' vertical portions o' t' ingenious motor mount are made from 1/8" thick balsa wood while t' rings are from 1/8" Masonite, all laser cut..."
"T' airframe tube is also laser notched for through t' wall construction o' t' large main fins."
"T' landin' gear uses real springs for shock dampening."
"T' assembly procedure is laid out in a logical 'divide and conquuer' stragety..."
"In t' end, me hearties, arrr, it took me about four hours o' assembly."
""T' six small fins (3 canards and 3 secondaries) are surface mounted."
"...worrisome be t' possibility that lack o' adhesion betwixt t' balsa fins and t' ureghane landin' gear nosecones may end up leavin' t' outboard sections o' t' main fins unsupported and easily broken. Ya scallywag! Begad! Fortunately, Vega would have t' land almost on its side t' cause such damage."
"To provide an attachment point on t' tail endo fo t' hollow cast nosecone, t' kit comes with a Masonite disk and a screw eye."
"For those that like finishin' rockets, shiver me timbers, this bird presents a wealth o' surfaces t' sand, me bucko, shiver me timbers, seal, and paint."
"Vega's first launch...the F21 power plant should have carried Vega little more than 1000 ft up... landed over 1/2 mile downrange."
"Landin' t' Vega with significant ground speed caused minor damage t' one o' t' landin' struts. Begad! Avast, me proud beauty! Even with a 30" parachute..."

Overall, t' article shows that this is an involved kit t' build, ya bilge rat, great t' look at, and interestin' t' fly. Well, ya bilge rat, blow me down! T' author noted that he has also built other QModelin' kits and believes t' "Q" in QModelin' is for Quality (Just as QModeling says).