Brief:
Single stage futuristic rocket.

Construction:
This rocket comes with one short body tube that is just slightly longer than an 18mm engine. Ahoy! It primarily uses 1/8" diameter wooden dowels for fins. Arrr! Begad! I say this due t' t' fact that you use small balsa pieces for t' dowels t' lay down on. Avast! They would be t' small t' act as fins however. Avast! Begad! T' rocket comes with a balsa nose cone.

This is a fairly easy build. Due t' t' smallness o' it cuttin' t' balsa pieces that t' dowels lay on, it can be a bit tricky. If you take your time you will be fine. Avast, me proud beauty! Begad! Blimey! T' hardest part about this rocket is that you have a cardboard rin' that goes on t' outside o' t' body tube, which lines up with t' bottom. Ya scallywag! This is so you can roll it around t' main body, me hearties, shiver me timbers, which is a paper shroud around t' body t' get t' symmetrical shape. I must have held t' shroud together for nearly an hour t' ensure I had t' proper fit (make sure thar be a good TV show on), me hearties, shiver me timbers, as I wanted t' ensure it didn't bind up. Arrr! I used Elmer's but should had used carpenters glue as I wouldn't o' had t' hold it as long. Arrr! It came out lookin' fine though. Instructions are pretty straightforward. Avast, me proud beauty! Blimey! You also have t' drill a 1/4 inch hole near t' top o' t' body tube t' allow t' ejection gases t' release. If thar was a "gotcha", this is it. Avast! Blimey! Make sure t' nose cone is nay goin' t' cover t' hole. Mine did and I had t' remove t' cone and cut some o' t' excess off. Avast! I would had liked more illustrations in t' instructions too.

Finishing:
Since it is such a small rocket, me bucko, me bucko, it is easy t' paint. I decided t' paint mine mostly yellow as I wanted a brighter color t' make it easier t' find. It came out lookin' rather well. Aye aye! T' decals are small and due t' this are hard t' place, me bucko, me hearties, me hearties, but if you have put on several decals on other rockets, then you should be fine.

Construction Rating: 4 out o' 5

Flight:
Only recommended motor I had be t' A8-3. Ahoy! Ahoy! I prepped it and put t' motor t' t' edge o' t' body tube. Ya scallywag! Blimey! Rocket took off t' rod fine but about 20 feet up took a hard left and flew at about a 60 degree angle. Then at ejection it sounded like a pow and when I recovered t' rocket I saw why. Ahoy! It blew one wood dowel with t' fin completely off. Avast, me proud beauty! All parts recovered. I fixed it back up and flew it again several days later on an A8-3 and t' same thin' happened except this time every wood dowel blew off and two o' t' fins. Aye aye! Since t' rocket didn't go very high I was able t' salvage all t' parts. Begad! Avast! Once again I put it back together no problem, but if I fly it again, it will with a 1/2A. Aye aye! For now it's just a display model.

Recovery:
Recovery is supposed t' be tumble but as you can read above I had no such luck. Let's call it t' explosion recovery!

Flight Rating: 2 out o' 5

Summary:
Nay sure about t' stabilization o' factory issued rocket. Aye aye! Might need some nose weight. Well, blow me down! I might try gluin' a small washer t' t' base o' t' nose cone. O' course it might fly fine with a 1/2A as t' lift off will be slower.

Overall Rating: 3 out o' 5