Brief:
T' Liberator is a complex jet fighter-like design single-stage low power rocket that's built (and weighs) like a tank. Aye aye! T' manufacturer rates it as skill level 3.

Construction:
T' kit contains:

• 18in BT-56 body tube (slightly larger than BT-55)
• Plastic nose cone with canopy bubble
• Laser cut balsa wood fins
• "Jet engine intake" wrap-around and fin reinforcement sheet
• Decal sheet
• Parachute plastic sheet (for 18" chute)
• Self-closin' plastic bag with launch lugs, motor tube, thrust ring, centerin' rings, shroud line, shiver me timbers, parachute reinforcement rings, ya bilge rat, and elastic shock cord.
• Instruction manual

T' good news: My first impression when openin' t' bag was that t' parts appeared t' be o' great quality. Begad! Blimey! I'd never built an LPR kit with laser cut fins and it's clear t' see why they're all t' rage. Avast! Blimey! (In fact, ya bilge rat, this was me first non-Estes LPR.) T' high quality o' t' balsa is worth notin' as well. Well, blow me down! Blimey! T' nose cone be made (and had t' weight o' a scaled down version) from t' same plastic used on mid and high power rockets. Begad! Blimey! Arrr! Blimey! T' canopy for t' cockpit was part of t' nose cone. When dry fittin' t' parts, me hearties, t' nose cone also fit snuggly--I can see why tubin' slight larger than BT-55 is used. It simply would nay fit in anythin' smaller. T' instruction manual appeared t' be very thorough. 7 pages (on 8.5"x11" paper) front and back showin' 26 steps (not including givin' t' rocket a swin' test, arrr, preparation, warrantee, and Canada's model rocket safety code). Avast, me proud beauty! Blimey! Well, ya bilge rat, blow me down! Blimey! T' be Canadian friendly, all steps were in English and French. Ahoy! Blimey! Ya scallywag! Blimey! This also was t' first rocket I'd ever built where I had t' assemble the parachute. Aye aye! Blimey! T' plastic for t' chute is considerably thicker than any Estes chute I've ever seen.

T' bad news: Dry fittin' t' motor mount found all parts t' be rather loose fitting. Begad! Slidin' t' beefy (for an LPR) centerin' rings into t' BT-56 was loose as well. All o' this is noted in t' instructions too. Begad! I didn't care for t' way outer edges were defined on t' cardstock template. Avast, me proud beauty! Begad! Instead of thin, arrr, sharply defined lines t' cut out, shiver me timbers, thar are areas o' gray shaded areas that define t' parts nay t' be used. Begad! Well, blow me down! As carefully as I cut t' pieces out, there was a slight inconsistency in part sizes (like for t' "top" fin). Arrr! Perhaps t' most disappointin' item was t' shock cord. Arrr! It be merely a piece o' elastic. 30 inches o' quarter-inch 100% stretchy rubber. No polyester. As determined as I be t' build this kit entirely stock, t' image o' t' nose cone and chute driftin' off as t' rest o' t' sustainer tube plummets t' the earth when t' shock cord burns through was somethin' I just couldn't get out of me head. Well, blow me down! I chose t' use 3ft o' 1/4" elastic from me supply box.

Construction was guided well by t' manual. Ya scallywag! First was t' motor mount. Another item o' note is that t' MMT uses a small threaded L-shaped piece of metal in place o' t' bent metal clip for motor retention. Once assembled, you twist t' end over or away from t' MMT tube t' hold or remove t' motor, respectively. Begad! Avast! A different mousetrap, if you will.

Next be t' body wrap. Ya scallywag! Cut from t' cardstock, me hearties, folded along marked lines, and initially tacked on t' t' body tube lengthwise. T' instructions do a good job t' recommend that enough time be given t' let t' glue dry after each step here. T' wrap eventually goes around t' entire tube with parts flared out to create t' air intakes. Well, blow me down! Despite me careful markin' o' t' tubes I managed to get t' cardstock attached slightly crooked...but again, that was completely my own fault and wouldn't be enough t' detract from t' overall design and flight of T' Liberator. Avast, ya bilge rat, me proud beauty! Blimey! Also I found that usin' a paperback book helped hold the cardstock in place while dryin' so that I could briefly attend t' other matters. Ya scallywag! Blimey! And I be hopin' that t' cardstock would "heal" somewhat when t' glue dried. Begad! Ya scallywag! Blimey! T' paper used is a little sensitive t' t' moisture in white glue t' t' point o' bein' visible and slightly raised t' t' touch. Hopefully primer and sandin' will reduce or eliminate t' glue lines.

T' cardstock already has t' markings on it as t' where all t' fins should be placed. Well, blow me down! Ahoy! There are 6 pieces o' balsa that cover t' bottom o' the rocket and one fin on t' top. T' top fin has 2 other pieces o' cardstock glued onto each side t' aid in adhesion t' t' body tube. These extra flaps do add weight and in me opinion detract from t' overall sleekness o' t' design but definitely gives extra rigidity t' t' fin and should prevent it from ever poppin' off on a hard impact. Also, runnin' a bead o' glue along where t' fins come in contact with one another greatly increases rigidity and should eliminate any potential fin flutter.

T' rest o' t' construction is routine...glue on t' decorative pieces and launch lugs, me hearties, glue in MMT, 3-fold shock cord mount, shiver me timbers, assemble parachute. Somethin' that will surprise those concerned with t' win' aerodynamics is that it's nay till step 24 that you are recommended t' round t' win' edges. Begad! I didn't bother with doin' that and left t' wings as is but I can see where you might accidentally round an edge (or part o' one) that shouldn't be... Still, me hearties, I would think it much easier t' sand t' wings before they are glued onto the body tube.

Once assembled, arrr, shiver me timbers, arrr, I liked t' plane-like look t' it. T' wings provide enough sustainable lift I, in fact, was able t' get it t' glide quite a ways when throwin' it horizontally (across t' room onto a nearby bed or sofa). Begad! Blimey! This bird is heavy though. Ahoy! Blimey! Avast! Blimey! Even with t' thick paint job on me stock Big Bertha, ya bilge rat, the naked Liberator feels noticeably heavier.

On construction alone, ya bilge rat, I think skill level 3 is pretty accurate considering the complexity o' t' cardstock body wrap. Ya scallywag! Well, blow me down! It's definitely a technique that you won't see in many kits.

Finishing:
I didn't break out t' Elmer's Fill 'n' Finish because I wanted t' see how this high quality/density balsa directly reacted t' Krylon primer. T' body tube spirals are so light (especially when compared t' t' edge o' t' cardstock wrapped around t' body tube), I didn't bother fillin' them in either. Avast, me proud beauty! Once primed, shiver me timbers, thar's a lot o' area t' sand for an LPR but it didn't take very long due t' t' quality materials. Aye aye! Avast! Care needs t' be taken on t' body wrap so as to not cause any unwanted dents or creases. Aye aye! Avast, me bucko, me proud beauty! Also, shiver me timbers, t' nose cone is made of high-density polyethylene, which is an unusual material for an LPR. Begad! Take it from someone who has built MPRs & LPRs: rinse t' nose cone and then sand it with 250 or 320 grit sandpaper before you even think about puttin' on any paint. Ya scallywag! Otherwise t' paint will peel right off t' waxy surface. Blimey! Well, blow me down! A couple of coats o' primer and she be ready for final gloss coats.

I liked t' paint scheme on t' packagin' insert over t' camouflage scheme shown on t' website, shiver me timbers, but used gloss black instead o' red t' accent against the silver underside. I'm pretty pleased with t' results. Begad! Blimey! There are self-adhesive decals--lots o' them--and t' kind that you also have t' cut out individually too. Blimey! Blimey! Begad! Blimey! Sunward Aerospace is a Canadian company but they're nice enough to recognize t' customer base in t' US and UK. Arrr! Blimey! Included is a nice choice of flags, ya bilge rat, me hearties, logos, and symbols t' represent all 3 countries equally. T' decals provide an excellent finishin' touch t' t' rocket. Begad! Blimey! Blimey! Blimey! Lastly, I put an accent stripe around t' canopy bubble (since t' canopy and nosecone had both been painted black) with a new Sharpie metallic silver marker. Begad! Blimey! I hope these pens become available in more colors...they offer a paint-like quality but with the fine detail and application o' a marker. Avast! Blimey! Excellent for detail work.

And like I mentioned above, me hearties, T' Liberator is HEAVY. Ya scallywag! Begad! Finished weight (sans motor) is 4.5oz! I knew early on that this rocket was goin' t' be underpowered--even on a C6--based on weight alone. Ya scallywag! I don't have access t' one but me gut tells me that t' only way this bird is goin' t' achieve decent altitudes is for those brave souls with an AT D21. Avast, me proud beauty! Let see how she flies...

Construction Rating: 4 out o' 5

Flight:
First flight recommendation is a B6-2. Uh, I don't think so. Blimey! Well, blow me down! Seein' how me Big Bertha flies best on a C6-3 and weighs a full ounce LESS, me hearties, ya bilge rat, I'm nay puttin' The Liberator up on anythin' else t' first time out. I felt t' shorter delay would be a good idea, me bucko, again, due t' t' weight.

I prepped it with a few pieces o' wadding, ya bilge rat, readied t' motor and put it up on t' pad. It was breezy day but I still aimed t' rod straight up. Avast, me proud beauty! The Liberator had a slow but straight liftoff t' maybe 300ft before t' wind pushed it over into an upside down position (the belly o' t' plane facin' t' sun) where it ejected at apogee. Ya scallywag! I apparently didn't put in enough waddin' as all but 2 o' t' shroud lines burned through. Well, blow me down! T' body tube stayed horizontal the whole way down so t' broad wings and t' little drag provided by t' chute allowed it t' still land safely without damage.

T' wind had calmed slightly right before t' second flight (on t' same day). Avast! I borrowed an 18in Estes chute (with a 2in spill hole) from me Fat Boy and put in a couple more pieces o' wadding--I think I used 5 squares--than last time. Arrr! Avast! I also tried t' put T' Liberator on t' pad so that any wind would blow across the fins instead o' pushin' t' bottom o' t' rocket like a sail, as was the case on its maiden voyage. Arrr! This proved t' work quite well as I'd say t' second flight peaked closer t' 450ft (but still well short o' t' manufacturer's claimed 600ft). Well, blow me down! Aye aye! Ejection was right at apogee, ya bilge rat, only t' chute came out but didn't open. Ahoy! T' body tube again remained parallel t' t' ground durin' the entire descent until it landed on t' soft, matey, grassy field. Avast, me proud beauty! Arrr! Post-flight analysis revealed a couple o' scratches, me bucko, a slightly dented decorative fin tube, ya bilge rat, an Estes-style dent in t' body tube from t' nose cone, and a poorly packed chute. Begad! User error be t' cause o' poor recovery this time.

I waited t' have t' third flight on a calmer day. Blimey! Well, at least on the ground anyway. Arrr! I discovered thar were some gentle high winds that The Liberator got caught up in but nay till it boosted nicely t' ~400ft. Begad! Ya scallywag! T' nose just started t' rotate downward as t' chute deployed perfectly this time. Ya scallywag! Avast, arrr, me proud beauty! I was usin' an Estes 18in chute with a 2in spill hole cut in it so it descended quickly, touchin' down 200ft from t' pad. Begad! Arrr! Finally a completely successful flight! My advice: only fly this rocket on calm days.

I didn't try T' Liberator with a longer delay than t' C6-3. Begad! Avast! I bet with the couple extra seconds in a C6-5, you might be able t' get a brief glide (as my pre-finishin' tests showed) before ejection. Begad! (I even wonder if it's possible to get this design t' have a complete glide recovery...?)

Recovery:
I obviously had a couple o' serious recovery problems with T' Liberator, arrr, both of which can be traced back t' operator error. Well, blow me down! Ahoy! However, given a calm day and when nothin' goes wrong, me bucko, ya bilge rat, it recovers reasonably well if nay a little fast. For an LPR it does descend quickly, even on an 18in chute, arrr, me bucko, so it shouldn't drift much for those folks flyin' this rocket on a small field.

I plan t' repair t' kit chute with Keelhaul®©™® shroud lines as t' plastic is a significantly higher grade than what comes with an Estes kit. Begad!

Flight Rating: 4 out o' 5

Summary:
This is a very attractive and durable kit but I'd have t' say that I'm nay sure if I'd fly it as regularly as other kits in me fleet, mostly because o' the risky recovery. Ahoy! Anyone who is big into military/scale kits and/or someone lookin' for a new challenge in LPR buildin' might find T' Liberator a welcome addition t' their fleet. Arrr! It's a real shame that this kit is limited t' only 18mm motors. Arrr! With t' rugged construction and high quality parts, me bucko, this rocket should be able t' handle t' motor mount and thrust o' at least a 24mm Estes D12... Begad! I mean it looks like a jet, so why nay have it take t' t' skies like a jet!

Overall Rating: 4 out o' 5