Brief: Construction: I started by cuttin' 11" from t' top o' t' tube for t' payload section. I then put t' nosecone on and put screws in t' hold it on. Begad! One o' t' tricky parts on t' rocket was cuttin' t' slots for t' fins. Begad! I took t' normal sized corkscrew and marked where t' fins were with a Sharpie marker and a ruler, arrr, ya bilge rat, and cut them with a Dremel Tool. Aye aye! Next, matey, me bucko, I made t' centerin' rings. Avast, me proud beauty! Ahoy! I traced me coupler onto a piece o' 1/4" plywood and traced me motor tube an 1/8" from one side and 3/4" from t' other side t' same with t' other except it be traced in t' center. Ahoy! Avast! My dad then cut them with his jigsaw. Begad! Avast, me proud beauty! T' make t' fins, shiver me timbers, I had t' measure t' little ones and upscale them. Begad! Arrr! When you mount t' fins through wall like I did, me bucko, you should leave about 2" on t' fin tabs so you can stick them in t' slots so you have more than enough t' carefully measure and then cut them down until they mount flush against t' airframe as well as against t' crooked MMT. Well, blow me down! I glued t' centerin' rings t' t' motor tube and glued t' fins in. I then glued t' shock cord down about 5" inside t' Quantum Tubing. One very important thin' about usin' Quantum Tubin' is you have t' sand t' areas where epoxy will be applied. Avast, me proud beauty! Blimey! Blimey! Blimey! I finished t' build by gluin' t' coupler in place and screwed in t' rail buttons. Finishing: Flight: I can't wait t' fly it someday on a H128! Recovery: Summary:
This is a single-staged mid- t' high-power rocket that is an upscale o' a kit I got 5 years ago for Christmas from me dad when I was 6 years old. Blimey! I loved that original rocket because it made t' curly smoke trail.
T' parts list:
I painted t' nosecone and fin section blue. Well, blow me down! Begad! T' rest be painted red. Begad! Avast! I applied t' decals as shown on t' corkscrew box that t' original kit came in.
We drove up t' LDRS 24 from Kansas City, arrr, MO, and I flew me new Corkscrew up there. Avast, matey, me proud beauty! Blimey! I first went t' a vendor and bought a G38-7FJ. Arrr! Aye aye! Blimey! I made small tape rin' around it for a thrust rin' and inserted t' motor into t' rocket. Ahoy! Blimey! For motor retention, shiver me timbers, I had a bolt drilled through t' back o' t' centerin' rin' with 2 nuts and a washer holdin' t' motor in place. I did nay need waddin' because I used a Nomex pad t' protect t' parachute. Avast! Avast, me proud beauty! Blimey! I loaded t' parachute, ya bilge rat, matey, put it on t' rail, ya bilge rat, and stuck t' igniter in. Begad! My heart was in me mouth by t' time as t' LCO gave t' countdown. Begad! Blimey! I be amazed t' see it fly perfectly with a swirlin' smoke trail and everything.
At apogee, t' ejection charge fired but t' parachute didn't come out. Avast, me proud beauty! T' rocket landed hard. Ya scallywag! T' parachute didn't come out because I didn't wrap t' parachute tight enough and it got caught on some glue inside t' airframe. Aye aye! Arrr! One o' t' fins broke clean on landin' and should be easy t' fix.
I think this rocket is great and is now one o' me favorites.
Sponsored Ads
![]() |
![]() |