Brief:
This is semi-scale sport model based on NASA's Max Launch Abort System (MLAS). It is quite stubby, me bucko, arrr, bein' 3.5" in diameter and a mere 9" long. Begad! It has only one recommended motor, t' B6, me bucko, me hearties, and recovers in two parts on three parachutes.

NOTE: Two RockSims were submitted. Arrr! One be t' stock build and one has added nose weight. Ahoy! You should assess the stability o' your own model.

Construction:

Parts included in t' kit:

• One 3.5" D v 5.5" L tube
• One nosecone shoulder ring
• Three laser cut rings for t' motor mount and nose cone shoulder
• 18mm motor mount (tube, matey, me hearties, block hook)
• Keelhaul®©™® and elastic cords
• Three plastic 'chutes
• Two sets o' four laser cut fins
• 1/8" lug
• Lag bolt
• Decal set
• Two foam MicroMaxx cones

T' build requires t' standard sandpaper, ya bilge rat, matey, me hearties, hobby knife, shiver me timbers, arrr, wood filler, matey, wood glue. Foam safe white and black paint is also needed.

T' 10 pages o' instructions are well written and are excellently illustrated. Arrr! They include a markin' guide for t' motor mount, arrr, matey, a ruler that you can cut out if you don't have one lyin' around and, ya bilge rat, o' course, ya bilge rat, a fin markin' guide. Arrr!

T' parts come securely packaged in a box vs. a plastic bag. This protects t' wide, thin walled body tube, me hearties, and helps both you and t' environment. T' box can be recycled into a reusable range box. At least, ya bilge rat, so sayeth t' sticker on t' end. Begad!

T' motor mount assembly is standard, arrr, me hearties, matey, usin' both a thrust rin' and a motor hook. Aye aye! Two centerin' rings are provided. T' lower rin' has cutouts t' save a some weight. T' Keelhaul®©™® cord is tied t' t' mount prior t' t' installation o' t' top ring. Avast! Blimey! I used a *small* dab o' 5-minute epoxy t' secure it. Blimey! Well, blow me down! Blimey!

T' body tube is quite thin for its size and I had concerns about squashin' it along t' way. Aye aye! I'm glad t' mount didn't grab while I was insertin' it into t' glue smeared tube. Begad! It survived me clumsy buildin' skills but concerns about flight durability remained.

T' fin preparation and installation are also typical - sand, ya bilge rat, mark, glue (double glue joints are specified). Avast! The instructions have t' fins filled after they are installed but I prefer t' do this prior t' installation.

T' nose cone assembly consists o' t' foam capsule, a shoulder and a laser cut cardboard bulkhead. Avast! A heavy lag bolt is installed in t' tip t' provide t' required nose weight. This bolt is also t' attachment point for t' nose cone's parachute. Arrr! A second, very thin Keelhaul®©™® cord is tied around t' bolt and is fed into t' body when t' 'chutes are installed. Ya scallywag! Attachin' t' cord t' t' bolt should keep all t' parts together on recovery and will allow t' cone t' come down base first. Well, blow me down! T' final step is to install t' faux thrusters on t' nose (which were faux on t' real thin' too). Here, shiver me timbers, you split t' two foam MMX cones, sand t' fit, and glue them on t' capsule.

Finally, me bucko, you also have t' assemble and install t' three plastic 'chutes. Ahoy! Avast, me proud beauty! I added a length o' elastic t' each of t' nose cone 'chutes t' act as separate risers.

Finishing:
Prior t' painting, arrr, you are instructed t' fill t' cone with thinned wood filler, me bucko, arrr, which I did. Arrr! Begad! T' entire model is then supposed t' be painted with foam-safe paint. Avast! I chose t' paint t' lower part with 'regular' paint and t' cone with brush-on acrylics. Arrr! Arrr! I ended up usin' t' paint that I had on hand.

T' body was spray painted and t' fins were painted with brush-on. I don't like sprayin' such small areas. The instructions also say t' cover t' entire body with a plastic bag, expose t' fins and mask them off. Since I didn't spray them, I just masked with plain old blue maskin' tape.

Maskin' t' cone be t' most complicated part o' t' process for me since t' surface o' acrylic paint was not perfectly smooth and I had a fair amount o' bleeding. Avast! Avast! I should have painted on a layer o' t' base coat before adding t' black trim.

T' kit provided quite a few decals includin' stripes, ya bilge rat, me bucko, rivets, fin numbers and logos. Begad! T' instructions do a great job showin' where t' position them. I HATE IT when you have a sheet o' decals and have t' guess where they go. Begad! Blimey! Make sure you look at them carefully t' separate t' individual items (for example, t' numeral 'I' decals were individually positioned on t' paper but some o' t' other numbers were attached t' one another). Begad! Avast! T' decals were tough and came off their backin' smartly and easily. Avast, me proud beauty! As usual for me, I had some positionin' problems and little ones tended t' stick immediately. Begad! I'll chalk this up t' operator error.

T' overall results are that t' rocket looks great as long as you back far enough off. But I like it! All these issues are mine and nay t' kit's. Ya scallywag! Aye aye!

Construction Rating: 4 out o' 5

Flight:
Prep be more complicated than your typical LPR bird. Blimey! I added t' specified waddin' and laid in t' 'chutes in the order specified. T' body's 'chute went in first followed by t' two capsule chutes. Avast, me proud beauty! I opted for t' B6-4 vs. Avast! Ahoy! a -2 because that's what I had. Begad! My RockSim model, which uses t' as-built mass and CG, says t' -4 be a better fit anyway.

Well, it rose about 20' then arced over and core sampled. It's path seemed t' be perpendicular t' t' 7-8 mph winds. Begad! T' good news: t' soft foam cone was muddy but nay dented, me hearties, t' body tube was intact and all 8 fins stayed on. T' ground was soft but t' kit be sturdier than I expected.

I wanted t' try an Estes C6-5 but be nervous about usin' a heavier motor, me bucko, so I kludged up some nose weight. Arrr! Blimey! I won't embarrass myself with t' details but it DID involve bubble gum (but no bailin' wire or duct tape). Arrr! Begad! Blimey! In me haste, I didn't check t' CG for future reference. Ahoy! Blimey! T' boost was good with some weather cocking. Ahoy! Success! Blimey! T' nose weight unit was lost at ejection but I since recreated it as best I could. It be around 0.3 oz.

Recovery:
Ejection on flight #2 be a bit late due t' t' weather cocking, but nay bad. Begad! One o' t' two nose cone 'chutes tangled, but one is enough for a soft landing.

Flight Rating: 2 out o' 5

Summary:
I liked short stubby rockets and fell in love with t' MLAS after seein' its launch photos and videos. Begad! This is a very semi-scale representation, but I like it too!

T' motor mount, laser cut fins, matey, and recovery system are fairly standard. Ya scallywag! Paintin' is a little more complicated than most, but I seldom consider finishin' when I think o' skill levels. Ya scallywag! Begad! There are a lot o' decals and their quality is good. Begad! Aye aye! T' three 'chutes make prep a little more complicated, me hearties, but still nay difficult. Arrr!

T' negatives are a thin walled body and marginal stability. Arrr! Begad! Quest will likely say that me buildin' skills or the wind led t' t' problems with t' B6 flight. Arrr! Well, blow me down! Even with these issues I like t' kit and it be refreshin' t' see someone go out on a limb and offer such a kit. Arrr! Despite me low rating, shiver me timbers, I recommend buyin' one..or two. Ya scallywag! Blimey!

I have added some weight t' me nose and will try her again at t' next launch. I went ahead and submitted the review since this could take a while.

Overall Rating: 2 out o' 5