I decided t' get a couple o' t' new (2001) Estes’ kits and thought t' Night Win' looked cool as it reminded me a lot o' t' SR-71. Well, blow me down! Then I decided t' build a series o' rocket "ships" that could be part o' a futuristic space fleet. Ahoy! Avast, arrr, me proud beauty! So along with t' Night Wing, I planned on buildin' t' Rogue Interdictor and an old Custom Stealth Interceptor that I've had hangin' around for about 4 years.

See me 18mm Futuristic Rocket Comparison Page

T' Night Win' comes with a BT-50 body tube, me bucko, an 18mm motor mount with motor retention, me hearties, (4) die-cut balsa sheets for all o' t' wings and RamJets, a die-cut paper (index card thickness) for t' body skins, me bucko, a launch lug, matey, 1/8" elastic shock cord, an 18" plastic parachute, a decal sheet and last but nay least t' nose cone. Ahoy! T' nose cone is from t' old SR-71 kit.

CONSTRUCTION:

T' instructions include 6 pages o' illustrated (with a few photos) steps that will guide t' builder successfully. Avast! T' instructions include flyin' instructions and two paint schemes. I've noticed Estes is providin' two paint schemes on their kit cards and think it is a nice idea. T' instructions back up t' kit card by describin' t' two schemes and showin' how t' various decals support each theme.

T' kit card is used for cuttin' out win' supports t' assist in buildin' t' rocket. In addition, two other alignment templates are cut out. These templates are used t' align t' various angles associated with buildin' t' ramjets, bottom cover and attachin' t' fins onto t' rocket.

In step 3, me hearties, me hearties, arrr, t' die-cut balsa pieces are assembled. Avast, me hearties, me proud beauty! I found it beneficial t' assemble t' ramjets and bottom cover and then apply a fillet on t' inside joints. Arrr! Well, arrr, blow me down! Then after drying, I sanded them so that t' tabs from assembly did nay stick up. Begad! Avast, me proud beauty! I think Estes should have shown this action as part o' this step.

Also don't be fooled here. Ya scallywag! There are enough balsa parts t' assemble two complete bottom covers. Begad! You only need one on t' rocket and yes I did spend several minutes lookin' at t' picture and then t' instructions and then t' picture again. I assembled both at this time, but didn't need one.

I found usin' t' alignment templates t' be a bit difficult. Ya scallywag! Well, blow me down! I'm nay sure thar be another way though, arrr, so take your time.

T' main wings are three pieces and are assembled by layin' them on a piece o' wax paper and alignin' with a ruler edge. Well, arrr, blow me down! This technique works well. Well, blow me down! It works better with a second piece o' wax paper and placin' a book on top t' ensure they are perfectly flat. At this point it would be wise t' seal and sand t' wings (as well as all t' balsa parts) considerin' it can be very difficult t' seal and smooth them out once t' rocket is fully assembled.

T' nose cone gets some weight added by takin' t' clay and rollin' it into very skinny strips and slidin' it into t' nose cone. Blimey! Arrr! Blimey! Then it is pressed into place with a pencil.

T' body skins are glued on after t' main wings are attached. Blimey! Begad! These are rather challengin' and depend on perfect main win' alignment. Ya scallywag! Ya scallywag! They are attached usin' carpenter’s glue. Begad! I found that t' glue made t' paper "wet" and caused a slight deformation where t' body skin attaches t' t' wings. You may want t' investigate a different glue, me hearties, maybe a spray glue, me bucko, matey, for gluin' these in place. Aye aye! Begad! If you use carpenter’s glue then be sure t' use it sparingly (very thin) and spread it out with your finger as outlined in t' instructions. Avast! Then once in place be sure t' rub your finger over it repeated times until t' entire joint is smooth and tacked down.

T' last part o' attachin' t' body skins is wrappin' t' upper section over and onto main fin edges. Avast, me proud beauty! Take your time on this and only do one side at a time t' ensure that t' seam is clean. My seams needed some trimmin' with a hobby knife t' look right.

Step 13 is difficult since you are gluin' on t' fins at specific angles. Avast, me proud beauty! T' get these angles you use t' alignment guides that are cut out from t' cover label back. Again, you might want t' use a fast settin' glue like Quick Grab t' ensure they don't change as t' glue dries. Ya scallywag! I didn't use Quick Grab, matey, me bucko, but rather set up a jig usin' books and pencils t' hold t' fin in place while drying. Begad! It worked.

For finishing, I used a very thick layer o' Plasti-Kote primer, sanded and hit it again. Arrr! Then I used Rustoleum "Hammered Look" Gold paint. One nice thin' about this paint is that it hides a lot o' finishin' flaws (not that me rocket had finishin' flaws [grin]). Ahoy! T' decals are peel-n-stick decals and adhered nicely. Ahoy! Avast! They are thin enough t' nay draw attention but nay so thin t' tear easily. Well, blow me down! I was pleased with these decals.

Overall, shiver me timbers, arrr, matey, for CONSTRUCTION I would rate this kit 4 points. I just think a couple extra steps about t' bottom covers would have been nice. Aye aye! Also, t' templates were difficult t' use. Ya scallywag! Lastly thar should have been some instruction on sandin' t' tabs from t' ramjets and bottom cover. Well, blow me down! Overall t' instructions are Estes quality and t' materials were fine.

FLIGHT/RECOVERY:

Estes recommends a B4-4, B6-4 and t' C6-5 motors for t' Night Wing™ and I took that advice for t' first two flights.

Preparation o' t' rocket suffers from t' same issues that t' SR-71 did...too small o' a body tube. Ahoy! Blimey! At least for me, I find it difficult t' get waddin' in there, ya bilge rat, ya bilge rat, then a full 18" parachute and t' shock cord. Ahoy! T' biggest problem be t' foldin' o' t' parachute. Begad! I have found that one fold works best givin' you a 4½" long rolled chute. Begad! Then I find that this length tends t' catch on t' 3-fold paper mount.

My first flight (pictured, me bucko, lookin' at t' bottom) was on a B6-4 with fairly calm wings. Blimey! Blimey! It gave a nice lift-off, ya bilge rat, somewhat slow and a low altitude. Begad! Well, blow me down! Blimey! It was interestin' because t' large winged bird seemed t' stall at apogee, matey, fall for just a moment belly down and then eject.

My second flight was on a C6-5. Ya scallywag! Again a slow lift off but much better and more enjoyable altitude. Well, blow me down! Avast! It seemed t' arc over and with t' nose cone slightly down, matey, ejected. Ya scallywag! T' parachute didn't unfurl, me bucko, but t' big wings seemed t' slow this rocket down on t' descent and it landed with no damage.

T' third flight be on an Apogee C10-4 on a perfectly calm day. All I can say is that this is an excellent rocket/motor combination. Blimey! Begad! T' C10 gets it off t' pad and with good altitude. Nice white trackin' smoke in these motors and ejection was at apogee. Aye aye! Just ensure you use more waddin' than I did with an apogee motor. Avast, me proud beauty! Blimey! Their ejections are more authoritative than t' Estes motors and it burnt a hole in me parachute and caused it t' stick together. Aye aye! Well, blow me down! No damage though.

Lastly, ya bilge rat, I must make me official complaint about t' shock cord length (again). This rocket is especially weak at t' nose cone junction since it is only t' card stock body skins. Blimey! Avast, me proud beauty! Use t' Estes shock cord and you will most definitely have a lot o' damage on this joint. This is well known about t' SR-71 and will translate t' t' Night Wing™. Begad! Well, blow me down! I used t' 3-fold paper method that is supplied, me bucko, me hearties, but I used a 24" piece o' Keelhaul®©™®, then t' supplied piece o' elastic shock cord.

My rocket weighed in at 4½ ounces (Estes indicates 3.2 ounces), arrr, and t' 1 time me chute actually opened proved that t' 18" chute is a nice size for descent rate. Arrr! Arrr!

For FLIGHT/RECOVERY, matey, I would rate this kit 4 points. My biggest complaint about flight be t' t' recovery system. Avast, me proud beauty! T' supplied shock cord is way too short as we all know, matey, and t' 3-fold method gets in t' way o' t' parachute that has t' be folded t' make sure a thin and long package. Ahoy! Ahoy! T' plastic parachute is fine, shiver me timbers, me bucko, but nylon (thin) would be better. Begad! T' flights are nice as t' large wings give this rocket some appeal and also varies t' movement verses a straight-as-an-arrow rocket. Well, blow me down! Blimey! Don't get me wrong, arrr, it is stable, arrr, but moves around a bit while goin' upward.

Overall, me hearties, t' Night Win' gives a nice challenge when buildin' and also provides a nice lookin' model when finished. Ya scallywag! Well, blow me down! I could have really spent more time with detail work and really made it look nice. It is also a good rocket for those that wished they could still get an SR-71. B motors are barely adequate, however, C motors are respectable and fun. Begad! Save your loot and buy a few Apogee C10's and even a D10 if you really want t' go all out. Blimey! Avast, me proud beauty! I give t' rocket an OVERALL ratin' o' 4 points. Ahoy!