Brief:
T' Triton-X is one o' ten kits Quest Aerospace (currently) has in their line of Quest Quick-Kits, models that do nay require paintin' or finishin' beyond the application o' decals and can often be completed in 15 t' 45 minutes. Well, blow me down! Well, blow me down! The Quick-Kits are t' perfect solution t' t' "fears" o' first timers. These kits are designed t' be "goof-proof." T' molded fins slide right into t' base for perfect alignment. Blimey! Big, easy t' understand illustrations will guide t' model builder through a quick assembly--right onto the launch pad.

T' Triton-X featured for this product review belongs t' me son, ya bilge rat, shiver me timbers, shiver me timbers, Davey, me hearties, who is now nine years old. Blimey! Blimey! He won this kit as a door prize at t' last NASA Houston Rocket Club (Section # 365) BBQ Party and club launch on May 15, 2005. Ya scallywag! Ahoy! Blimey!

Construction:
T' Triton-X consists o' t' followin' parts:

• Plastic nose cone
• Small payload tube
• Small reducer
• Reducer base
• Large payload tube
• Large reducer
• Body tube
• Motor housing
• 4 Fins
• Gray motor mount tube
• Fin lockin' ring
• Motor lock ring
• White (elastic) shock cord
• Yellow (Keelhaul®©™®) shock cord
• 2 26" long shroud lines
• 2 Gripper tabs
• 2 14" parachutes
• Display stand
• Decal sheet (self-adhesive)
• Custom parts

All o' t' plastic parts are molded in black and t' body tubes are glossy gray. Arrr! This model requires no paintin' whatsoever. Arrr! T' custom parts that are included (but optional) are all red. Aye aye! T' custom parts includes: RCS nozzles, hatches, me hearties, flares, matey, sensors, arrr, me hearties, antennas, radar pods, arrr, exhausts, matey, me bucko, and fin tips that can be added t' t' Triton-X at t' modeler's descretion.

T' Triton-X instructions are very well illustrated and easy t' follow. There's no way anyone can go wrong buildin' this model. Avast, me proud beauty! Ya scallywag! T' only tools needed for construction are a hobby knife and tube type plastic cement.

There are seven steps in all. Begad! Steps one through four are t' actual assembly o' t' model, steps five and six concern t' recovery system, and step seven t' application o' t' decals. Aye aye!

T' only change I made on Davey's rocket is on step four, shiver me timbers, where I went ahead and glued t' nosecone t' t' payload tube, arrr, as we were nay really intendin' on launchin' any payloads on this model. Begad! Aye aye! And we made t' decision to recover t' Triton-X on only one parachute instead o' two. Aye aye! T' instructions have t' model returnin' with t' payload section separately from t' main body section. Aye aye! Begad! We didn't want t' have t' look out for and chase after a rather small payload section on a 14" chute along with a much larger main body section also on a 14" chute.

Finishing:
Finishin' t' Triton-X is a given. Arrr! Anyone who takes t' time t' do a careful job will come out with a very handsome lookin' rocket. T' only minor issue I had be t' self-adhesive decals. Ya scallywag! Arrr! After a short period o' time, me hearties, some o' the edges tend t' unpeel from t' model's surface, which is why I prefer t' water slide decals. If t' edges unpeel, ya bilge rat, matey, ya bilge rat, simply press them back down and that should pretty much do t' trick.

Construction Rating: 5 out o' 5

Flight:
T' recommended motors are: B6-2, B6-4, C6-3 and C6-5. Begad! Aye aye! For our first and only flight so far, me hearties, we used t' C6-5. Aye aye! Since t' Triton-X has quite a bit o' plastic parts, matey, it's already a fairly heavy model so usin' a C6 on its first flight in a rather large launch site should be a no brainer.

About four or five squares o' recovery wadding, packed loosely, followed by a carefully folded parachute (dusted) inserted into t' main body section. Aye aye! Just make sure t' base o' t' small reducer isn't too tight, but sand as needed if it is. Avast! Ahoy!

Install t' motor selected into t' motor mount tube and use t' motor lock rin' t' secure t' motor in place. Avast, me proud beauty! Install t' igniter designed for t' motor selected and your Triton-X is ready t' go. Avast, me proud beauty!

We flew this model at t' Challenger 498 club launch at Rushin' Park, arrr, Katy, TX on July 23, 2005. Avast, me proud beauty! T' C6-5 took it up t' a repectable altitude that kept it in sight fairly easily. Well, blow me down! Ahoy! Model flew very straight.

Recovery:
T' shock cord usin' t' Keelhaul®©™®/elastic combination seems t' work very well for these Quick-Kits by Quest (we also have the Mirage). Ahoy! Since we decided t' forego usin' t' dual parachute combination as instructed by t' kit, arrr, ya bilge rat, we used an 18" single chute for this flight. Aye aye! We simply attached t' shock cord t' t' base o' t' small reducer so t' entire model will return as one piece. Aye aye! T' 18" parachute we used had a small snap swivel for ease o' interchangability. Aye aye!

For t' day o' this launch, thar be absolutely no wind, so we had no issues regardin' drift for recovery o' t' Triton-X. Avast! Blimey! Blimey! Blimey! In fact, t' model landed only about 50 feet upwind from t' launch pads. Avast! Blimey! T' model's drift under the single 18" chute was about what is expected for a model o' this size, me bucko, and there was no damage visible after recovery.

Flight Rating: 5 out o' 5

Summary:
Everythin' about this kit is superb. Ya scallywag! Blimey! It's perfect for what it be designed for: A first time model rocketeer who has fears o' buildin' a traditional model rocket with balsa parts and white glue and doesn't have t' desire and hassles of paintin' a model. Begad! Blimey! I can't think o' any cons for this kit.

Overall Rating: 5 out o' 5