Brief:
This is a very sturdy 4 inch diameter, ya bilge rat, 39 inch tall advanced model rocket made by AeroTech. Begad! It is a stubby model capable o' handlin' anythin' from G t' H power, arrr, sports piston ejection, and comes equipped with a 29mm motor mount. Avast!

Construction:
T' component list for this rocket is:

• 1 4 inch diameter, shiver me timbers, 23 inch long pre-slotted cardboard body tube
• 4 pre-shaped plastic fins
• 1 12 inch long, me hearties, matey, cardboard motor tube
• 1 16 inch long plastic nose cone
• 1 piston cap
• 1 piston sleeve
• 1 motor hook
• 2 four-fin FIN-LOK rings
• 3 centerin' rings
• 1 bulkhead disk
• 1 spacer, HP motor (black tube)
• 1 spacer, me bucko, Hobby motor (yellow tube)
• 1 ejection gas baffle
• 1 screw eye
• 1 18' long by 5/8" wide elastic shock cord
• 1 two ¼ inch launch lugs
• 1 42 inch diameter hexagonal nylon parachute
• 2 piston buckles
• 1 decal sheet
• 1 instructions

This rocket was an absolute dream t' assemble. Avast! Blimey! I have already built two AeroTech kits, arrr, so I could have built this without t' instructions. Blimey! Arrr! However, I chose t' use them because I am cautious about every rocket I build. Begad! I did modify t' rocket a bit after it wounded itself a couple o' times. Blimey! Those modifications will be explained in t' flight portion o' this review. T' instructions tell you t' use CA glue for t' construction, but I used 5 minute epoxy which worked great. Blimey! T' instructions were thorough and had some good accompanyin' illustrations. Ahoy! The construction started with t' motor mount. Ya scallywag! T' motor mount tube has a pre-drawn line down its length, me hearties, allowin' you to make precise measurements on t' tube. Avast! T' middle centerin' rin' is slid onto t' "back end" o' t' motor mount tube with t' motor hook under it (unlike on Estes rockets, arrr, t' tab on t' motor hook that would normally go through t' motor tube goes t' "wrong" way so that it hooks behind t' middle centerin' ring, me bucko, me bucko, makin' a very solid attachment o' t' hook). Well, blow me down! Blimey! T' front FIN-LOK rin' is slid onto t' tube so that t' back edge o' it is 4 inches from t' "back end" o' t' tube. Aye aye! T' aft FIN-LOK rin' is then slid on until it's front edge is 1-15/16" from t' back end. T' FIN-LOK rings must be aligned, matey, otherwise t' fins will nay fit. Begad! All these components are glued into place--and don't get glue in t' FIN-LOKs! T' ejection gas baffle cap is then glued into t' opposite end o' the tube, me hearties, and t' forward centerin' rin' is glued on top o' t' baffle cap. Avast! T' motor mount assembly is inserted into the slotted end o' t' body tube and t' FIN-LOK rings are lined up with t' slots. Blimey! Glue is applied t' t' whole root edge o' one fin, matey, t' fin is inserted into one o' t' slots, and it is snapped into t' FIN-LOK rings. Ahoy! T' same is done for t' other three fins. T' fins are filleted with glue and internal fillets are applied inside t' fin-can. Ahoy! Begad! T' rear centerin' rin' is then slid into place and glued. Arrr! Begad! On t' forward centerin' ring, arrr, an airtight seal o' glue is applied in order for t' piston ejection system t' work properly. Avast, me proud beauty! Tie t' shock cord t' t' screw eye, ya bilge rat, screw it through the bulkhead disk, ya bilge rat, and then screw it into t' baffle cap on top o' t' motor mount. Begad! T' piston cap is glued into t' piston sleeve an eighth o' an inch from one end o' t' sleeve. Avast, me hearties, me proud beauty! T' piston is then fastened t' t' shock cord with two plastic buckles. Ahoy! You will probably notice that t' piston is too large t' fit into t' body tube at this point. Avast, me proud beauty! Blimey! Since I have read t' other reviews for this rocket, arrr, I be nay surprised at this. Well, me bucko, blow me down! I do nay think that an "advanced model rocket" such as this should be able t' be assembled in one's underwear, ya bilge rat, shiver me timbers, standin' on one's head, and with one's hair ablaze (in other words, "should nay be easily assembled"). Avast! A little sandin' never hurt anybody. Well, blow me down! Well, me bucko, blow me down! I would recommend primin' and sandin' t' piston smooth after gettin' it t' right size t' remove t' "fuzzies" and make it smoother. Avast, me proud beauty! Lastly, t' nose cone and parachute are then attached t' t' shock cord. Ya scallywag! My rocket weighed in at 38 ounces. Arrr! That's it for construction!

Finishing:
Finishin' couldn't have been simpler. Blimey! Avast, me proud beauty! Since t' instructions just say, me bucko, shiver me timbers, "paint this red, paint that yellow," and because New Holland is a company which sells farm equipment that is painted red and yellow, I decided t' have a little joke with t' paint on this rocket. I primed and sanded t' rocket several times but did nay fill t' spirals as they are nay deep. I then proceeded t' paint t' fins New Holland yellow, shiver me timbers, nay protectin' anythin' from t' overspray. Avast! Avast, me proud beauty! I scuffed t' yellow overspray on t' rocket with 400 grit sandpaper, masked t' fins, me bucko, and painted t' rest o' t' model with New Holland red. Begad! Ya scallywag! I allowed t' paint about a week t' fully dry and de-gas before applyin' t' self-adhesive decals. Blimey! I cut out t' decals, dipped them in slightly soapy water, matey, me bucko, shiver me timbers, and applied them t' t' rocket. Well, blow me down! T' finished result was fabulous!

Construction Rating: 5 out o' 5

Flight:
Now for t' really good stuff--the flying! I now have five flights on t' rocket, and it is scheduled for three more at our next launch. Avast, me proud beauty! Avast! T' first flight was on a single use G79-4W. Avast! Instead o' usin' a maskin' tape thrust rin' (ugh!) as outlined in t' instructions, I used a piece o' PVC pipe with an inside diameter just large enough t' fit over the motor's forward closure and long enough so that when it butts up against t' baffle cap (used as a thrust ring) the motor is retained by t' motor hook. Arrr! I also put a small amount o' sheep wool waddin' around t' baffle cap t' lengthen t' shock cord's life. Well, blow me down! Blimey! Since its readily available, I use unwashed sheep wool for me recovery wadding. It is flameproof, me hearties, arrr, cheap (in me case its free), me bucko, and easy t' use. Unlike toilet paper or tissue which smolders when blown upon, sheep wool is put out by t' slightest breeze (if you can even get it t' catch fire). T' first flight was spectacular: huge roar, me bucko, long cracklin' white flame, arrr, tons o' billowin' smoke, arrr, me bucko, and about 900ft AGL. Ahoy! T' delay was right at apogee, the chute inflated, matey, and it touched down without a scratch about 300 feet away. Aye aye! AeroTech advertises this rocket as "a short, ya bilge rat, fat rocket with slow lift-offs." On t' G79W it went quite a bit faster than I would call "slow," but that's just me opinion. Arrr!

T' second flight (on t' same day) was on a G38-4FJ. Avast, me hearties, me proud beauty! It was nay nearly as loud as t' previous flight, but it was what I would call a slow liftoff. Begad! Ejection occurred just as t' model turned nose down (about 550ft), ya bilge rat, t' parachute opened, shiver me timbers, but it somehow got tangled around t' piston, arrr, matey, reefin' t' chute slightly. Blimey! Aye aye! It landed with a bounce about 150 feet away. Begad! One fin fillet was cracked and t' aft end o' t' body tube had a large crescent shaped din' in it. Avast! Begad! I used a piece o' 4" tube coupler t' reinforce t' tail end o' t' rocket, shiver me timbers, put epoxy over t' cracked fillet, and added about 3 ounces o' nose weight (I be afraid that t' tube coupler would hurt t' rocket's stability). Well, blow me down! Avast! T' rocket then weighed about 43 ounces. Avast, me proud beauty!

T' third flight was on another G79-4W with t' same great flame, smoke, and roar as on t' first flight. It was noticeably slower off t' pad than before and t' ejection be right on. Blimey! T' peak altitude was around 800ft. Aye aye! The 42" parachute was too small for t' heavier weight o' t' rocket, and it recovered about 300 feet out with a cracked fillet (the same one that I repaired) and a kink in t' tip o' one fin. Begad! Ahoy! It be time for more mods. Aye aye! Begad!

I unscrewed t' screw eye from t' baffle cap and noticed that t' bulkhead disk was slightly charred. Ya scallywag! So I cut out a piece o' flat tin t' same shape as t' disk and epoxied t' tin onto t' disk t' keep it from burning. I then epoxied t' screw eye into t' baffle cap. Aye aye! T' shock cord is now attached via a quick link. Avast, ya bilge rat, me proud beauty! I also scrapped t' elastic cord and used a piece o' 3/16" nylon rope instead. Arrr! For those o' you who don't like rope for use in rockets, matey, me hearties, just think about this. What be t' rope tied to? In me rocket's case, ya bilge rat, its tied t' a quick link which has a tensile strength o' 220lb. What be t' quick link attached to? A mild steel screw eye which has a tensile strength o' under 100lb. Begad! This screw is in turn screwed into a piece o' plastic (the baffle cap). Avast, me proud beauty! Avast! Since this recovery system be designed t' work in this rocket, a piece o' tubular nylon capable o' withstandin' two tons o' force is nay needed.

T' piston is now modified with a long nut, washer, ya bilge rat, and 2 eye bolts so that t' shock cord is actually in two sections: one from rocket t' piston, arrr, arrr, and t' other from piston t' nose cone. Avast, me proud beauty! T' eye bolts only need t' be unscrewed to remove either section o' t' shock cord from t' piston. Begad! Avast! I also made a 60 inch diameter parachute out o' red ripstop nylon t' be used instead o' t' kit's 42" one. Aye aye! Since this chute is so huge, me bucko, shiver me timbers, I turned t' piston around so that the piston cap faces t' tail end o' t' rocket instead o' t' nose end. This gave me a lot more room, ya bilge rat, but it still wasn't enough t' fit t' parachute.

I cut off t' bottom o' t' nose cone so t' shoulder is now only 2 inches long. T' nose cone had a pronounced wiggle after this. I then made a bulkhead plate with a U-bolt for shock cord attachment out o' ½" plywood, inserted it as far as I could in t' nose cone, and epoxied it firmly in place. T' chute now fits easily. Arrr! T' bulkhead be also slightly out-of-round which eliminated t' aforementioned pronounced wiggle o' t' nose cone. Arrr! Arrr!

I also made a cool way t' retain your RMS casing. I cut out two strips o' aluminum sheet 3/8 inches wide by about 2-¾ inches long. Blimey! Blimey! I marked a line on each one about ½ inch from one end and made a 90 degree bend at this line. I then drilled two 1/16 inch holes in t' long ends o' t' resultin' "L" shaped pieces (all o' these measurements are approximate because t' device is permanently installed in t' rocket and I didn't write down the actual measurements). Blimey! Blimey! Blimey! Blimey! I procured two screws and in t' short end o' each piece drilled a hole slightly smaller than the diameter o' t' screws. With t' same drill bit I then drilled two holes in t' aft centerin' rin' about ¼ inch away from t' motor tube on each side is such a way that they did nay interfere with t' operation o' t' motor hook. Blimey! Blimey! I then inserted me "L" shaped brackets into t' tail o' t' rocket short end down and screwed them into the rocket by hand. Well, blow me down! Blimey! T' result is two posts with holes in them stickin' above t' motor tube. Ahoy! Blimey! In t' flange on t' aft closure o' me RMS casing, matey, I drilled two holes which line up with t' holes in t' brackets. Begad! Blimey! Ya scallywag! Blimey! Blimey! Blimey! If done correctly, this system allows t' motor t' be smartly and easily safety wired into t' rocket, me bucko, eliminatin' any chance o' t' casing ejecting. Ya scallywag! Blimey! Blimey! Blimey! Blimey! Blimey!

Instead o' t' yellow, me hearties, me bucko, poor fittin' cardboard spacer supplied with t' kit for use with t' RMS casing, I had my dad make an aluminum one on t' lathe which fit perfectly. You will also notice that t' instructions recommend wrappin' maskin' tape around t' junction betwixt t' motor tube and t' aft end o' t' motor with maskin' tape to, "prevent any ejection gas from escapin' around motor." This is a totally unnecessary step. Blimey! Blimey! If t' ejection gas "wants out" it could just escape through t' nozzle, arrr, but this is 4F black powder we are talkin' about. It pressurizes too rapidly t' waste time goin' through tiny holes. Blimey! Blimey! If t' piston doesn't move and t' motor stays in, the ejection gas will over-pressurize t' motor/body tube, arrr, and make an escape hatch through t' motor/body tube. Well, me bucko, blow me down! Blimey! With all these modifications, t' rocket weighed 49.6 ounces.

T' first flight after these modifications was on a G64-4W. Blimey! T' sound, flame, and smoke from this reload were awesome! It went maybe 500ft. Blimey! T' rocket performed a slight lean with t' wind, me parachute deployed at apogee, and t' rocket floated down very slowly about 200 feet away without a scratch on it. Begad! Begad!

T' next flight (on t' same day) be on a single use G77-4R. Aye aye! I doubt that it made 500ft; it looked more like 400. T' red flame was marvelous and t' noise be thunderous! It again did its lean with t' wind. Begad! Arrr! It recovered closer this time about 150ft away. Ahoy! Avast!

I intend t' fly it on a Cesaroni 3 grain G106 Skidmark at t' next launch. That oughta be killer!

Recovery:
Recovery, arrr, as already discussed, ya bilge rat, was great on most o' t' flights, ya bilge rat, with only 2 issues. Aye aye! T' oversized parachute will hopefully eliminate any future landin' injuries t' t' rocket. Blimey!

Flight Rating: 4 out o' 5

Summary:
T' Sumo is a great rocket all around. Aye aye! Ya scallywag! I'm only 14 years old, and I was able t' assemble it with ease. Blimey! It's big, ya bilge rat, fat, loud, me hearties, and crowd pleasing. Arrr! I highly recommend this rocket t' anyone wantin' t' get into mid or high power.

Overall Rating: 5 out o' 5