Aerotech - Initiator Starter Set {Launch/Starter Set}

Aerotech Initiator Starter Set

Aerotech - Initiator Starter Set {Launch/Starter Set}

Contributed by Bob Albright

Construction Rating:
Flight Rating:
Overall Rating:

Manufacturer:

Aerotech

Rocket Pic Brief:
T' Initiator is a good looking, arrr, me hearties, mid powered rocket that flies on 24mm and 29mm rocket motors. T' starter set comes with everythin' needed t' build and launch t' Initiator.

Construction:
T' Initiator comes with (1) main body tube, me hearties, a motor tube, 3 fins, matey, a nose cone, arrr, a gas baffle system and recovery system. Ya scallywag! Avast! T' starter set also includes a launch pad, ya bilge rat, launch controller and 2 motors.

T' Initiator is one o' t' easiest rockets t' build and with great illustrated instructions. T' kit went together very smartly and t' way t' fins snap in, matey, make alignment a breeze. Avast, me proud beauty! T' rocket needs no special tools t' build and is very sturdy. Aye aye! We have launched our Initiator 25 times with only one 1 bad landing, we broke 1 fin off after launchin' her on a G64 with no parachute (but it was easily repaired). Avast, shiver me timbers, me proud beauty! T' controller has worked perfectly, ya bilge rat, matey, but we did give away t' launch pad and built our own (the Mantis pad wasn't goin' t' hold up t' me and me 3 boys).

Finishing:
T' Initiator was very simple t' finish and came with very nice decals. Avast! Aye aye! T' Initiator is a great lookin' rocket and we have flown her with both t' low powered rocket guys and t' high power rocket guys. Begad! She blows t' low powered rockets away and can keep up with t' high powered rockets.

Construction Rating: 4 out o' 5

Rocket Pic Flight:
We have flown our Initiator 25 times on every thin' from E's t' big G's. Arrr! Blimey! We are havin' a lot o' fun flyin' her on our new 29mm 40-120 reloadable system. Ya scallywag! Blimey! Avast! Blimey! She will fly fine on t' E size motors, arrr, but really roars on a G64. Ya scallywag! Blimey! This rocket uses no waddin' and t' recovery system has worked perfectly. Avast! Blimey! Begad! Blimey! Our Initiator has flown straight every time.

Recovery:
Our Initiator has been recovered perfectly every time except t' time I left t' parachute out (but that's a long story). T' shock cord is sized fine for t' size o' t' Initiator.

Flight Rating: 4 out o' 5

Summary:
As a first rocket in t' mid-power range, you couldn't find a better rocket with its ease o' buildin' and strength. Begad! Begad! This is our 1st mid-powered rocket (we have many low and high powered rockets) and we have t' already mentioned 25 launches with a lot more t' come from our Initiator.

Overall Rating: 4 out o' 5

Other Reviews

Aerotech Initiator Starter Set By Chris Bovia (March 7, 2014)
Easy to build kit - especially with the online tutorials that I managed to save as I was unable to find them more recently. Painted the rocket white with a red nosecone. So far it works great! Components Made as per kit plans and included supplies. Built with 5min epoxy to withstand higher impluse G flights. /h2 Kit came with everything including ...
Aerotech Initiator Starter Set By Andrew Godbold
The recovery system on this rocket is a large yellow parachute. Although this chute is very large it can be hard to see at a great distance. The only problem with this chute is that it easily catches in trees and this was the fate of my rocket. This kit comes with one body tube without a payload section. There are also a motor mount tube, molded plastic nosecone, and 3 through the wall ...

Flights

Comments:

M.C.D. (January 1, 2001)

I too purchased the Initiator kit and found the Mantis launch pad very weak where the legs meet the base. I solved this problem with electrical tape and a plastic cup. I simply taped the leg joints and cut a plastic cup to fit under the whole unit, snug between the bottom of the pad and the ground. The cup now absorbs the weight load and the legs are stabilizers. Although it's a low-tech solution I have found it to be effective. As for the rest of the kit, magnificent! The Initiator rock is great, after 8 nominal to spectacular flights on F-20 & G-35 econo-jets there is little to no damage. The Interlock launch controller is great, but as the reviewer suggests it needs to be modified to use standard Estes type igniters. All in all a great kit, I bought mine for $118.00 from Hobbylinc.com. I would not recommend paying more than $$150 for the Initiator Starter Kit, at this price or below I could call it a Gem.

J.M. (April 1, 2001)

Great starter set. The only thing that was a problem was the controller. I followed the instructions to the "t" and rechecked 3x, but found that I had to clamp the battery clips to the opposite terminals of what they were labeled. Also, I bought my entire setup with reloads from Discount hobby in NY for $89.00

T.S. (April 1, 2001)

This was my first mid-power kit and I still love the simplicity of the thing. The only thing I've done different than most was to add expanding foam in the void around the motor tube/fin-lok area. Foam it, let the foam set up, remove excess, glue in aft centering ring. Many launches and no damage yet.

N.P. (November 16, 2001)

I bought this kit and I am very happy. I haven?t flown it yet but my friend took it with him and flew it. It didn't come back with a scratch on it. He said it was a spectacular sight. I recommend this rocket to everyone.

J.V. (May 16, 2002)

Just a quick comment on AeroTech's customer service. My kit came packaged nicely, but the nose cone appeared to be defective. It had a very rough, almost pock marked finish, bad enough that there wasn't much I could to to clean it up for finishing. A quick email to AeroTech, explaining the problem, and about a week later I had a new nosecone sitting on the front porch for me when I got home. Excellent customer service, thanks AeroTech

J.H. (May 29, 2002)

The RMS version of this kit was my entry to the mid-power market as well. I followed the (very easy) instructions to the letter, using CA glue. Just flew it on Sunday. Winds were probably a little strong for the flight, and the first flight on an E16-4W should have removed the rocket from my inventory. The rocket weathercocked and proceeded to go ballistic. Ejection occurred approximately 10 feet off the ground, snapping the rocket around just over 180 degrees, causing it to land fin first in the ground. After pulling it out of the ground (requiring 2 hands to do so), I found that the only damage had been that the back of the fin root had popped out of the Fin-Lok. A quick line of CA along the fin base and the rocket was ready for it's 2nd flight of the day on an F40-7W reload for a perfect flight and recovery (if you don't mind the mile and a half walk due to the wind). This is one tough bird, and the Fin-Lok system made field repair a snap, quite literally!

J.M. (May 31, 2002)

I too, had the same experience as another person here. My launch controller had its wires reversed, if following the instructions to the "t". Wonder if it was a bad batch?

L.V. (November 24, 2002)

I too have the starter kit. It was my first mid-powered composite fueled rocket. My starter kit had the 29-40/120 reloadable motor with a E16-4 and a F40-7 reload. The rocket is easy to build and is a really nice looking rocket. The interlock controller works well and went together easily. The pad did also, but is on the flimsy side. I fly the Initiator on mostly the F40 load but have flown it on the G64 which is spectacular. The F52 and F22. Great flying rocket one of my favorites.

A.M. (November 25, 2002)

I purchased a second hand initiator starter set. My first mid power rocket. I agree with all the other reviewers regarding the Mantis launch pad, weak leg connections (mine broke all by themselves setting in my room). I solved this by carefully drilling two holes through the plastic and legs, and used bolts with wing nuts to hold them together. Now the kit was another story. Every thing went together well, and despite some concerns regarding the fin to fin-lock alignment problems, mine went together well. I used 30 min epoxy on the fins. I have launched this rocket 10 times, on either F20 , or G35 econojets. Only problem occurred when on its second flight the motor CATO?d on the pad. Now this is one tough bird, the motor CATO did no damage to the body or fins. I picked up the motor parts off the ground. This rocket rocks on G35 EconoJets. I highly recommend this rocket to any one. The Mantis pad, is another story. Unless Aerotech addresses the leg connection problems, I?d shy away from this.

J.I. (January 26, 2005)

FYI, the swing arm of my Mantis pad broke after about a year. I sent Aerotech an email asking for the purchase price of a new one. To my surprise they replied that one was in the mail. I have never had better service with problems than with Aerotech.

Steve Lindeman (March 8, 2014)

My starter set came with only the E16-4W reload wich I used for the maiden flight and was OK but not dramatic. I agree with most on the flimsy design of the Mantis pad. I'm still using it, but it's in constant need of repair for the legs. Need to try and bolt them on. My 2nd & 3rd flights were on Aerotech single use F27-8R redline motors which I think are the perfect moter for this rocket. For a stellar flight try the new 29mm single use Mojave Green G78-7G by Aerotech. Awesome flight!

Post a Comment