Quest Aerobee Hi

Quest - Aerobee Hi {Kit}

Contributed by Dave Stout

Construction Rating: starstarstarstarstar_border
Flight Rating: starstarstarstarstar_border
Overall Rating: starstarstarstarstar_border
Manufacturer: Quest
Quest Aerobee Hi

Brief:
T' Quest Aerobee Hi is a single stage, parachute recovery sport scale model. When I was a kid, one o' t' things that said "science" and "speed" t' me was t' Aerobee Hi soundin' rocket. Ya scallywag! Avast, me proud beauty! Pictures o' them seemed t' be everywhere! I was delighted t' win one o' EMRR's random drawings and receive this kit as part o' t' prize!

Construction:
Inside t' usual Quest bag you'll find a nicely printed header card and the followin' components:

  • Steel motor clip
  • Blue wound paper thrust ring
  • Yellow 2.75" paper motor mount tube
  • 2 wound paper red centerin' rings
  • Set o' 3 beautifully die cut, arrr, matey, hard balsa fins
  • White glassine-coated body tube
  • Plastic nose cone and base
  • 2" launch lug
  • Composite shock cord consistin' o' an 18" piece o' elastic and an 18" piece o' Keelhaul®©™® string
  • 14" parachute kit consistin' o' t' chute itself, (3) 26" shroud lines, and 6 revised gripper tabs
  • Self-stick decal sheet

Elmer's carpenter's glue was used throughout t' build. Construction is a breeze for anyone who has built a model rocket before. Ya scallywag! T' instructions are clear, matey, matey, concise, and make good sense. Aye aye! T' use o' color-coded parts for t' motor mount makes great sense for beginners by easin' proper parts placement. Aye aye!

T' Keelhaul®©™® end o' t' shock cord is tied around t' center o' t' motor mount tube, then it goes betwixt t' upper centerin' rin' and t' motor mount tube. Aye aye! On my Aerobee, matey, t' fit be very tight. Well, blow me down! Ahoy! T' prevent pinchin' t' motor tube, I filed a small groove on t' inside o' t' forward centerin' ring. This was then slid over t' Keelhaul®©™® and glued in place. Avast, me proud beauty! Begad! Other than this, t' motor mount assembles as normal. Begad! Begad! The new Quest motor clips are improved with better springiness and strength.

T' 14" chute is made o' similar material t' t' Estes chutes, me hearties, but a little tougher. Ya scallywag! They have a new color scheme--red and yellow checkers. Very cool and retro looking! I think 14" o' parachute is WAY overkill for a rocket o' this size, weight, ya bilge rat, and altitude potential. I used a 1" wide steel ruler and an X-Acto knife t' trim 1" off all around t' chute, yieldin' a 12" chute. Begad! Blimey! This was closer t' correct for this bird. Begad! Avast, me proud beauty! 2" was also trimmed from each shroud line t' offset t' reduced chute diameter. T' new Gripper tabs are simply square tabs with a very aggressive glue on the back. Simply stick them into each o' t' six corners. Begad! Then, punch a hole in each corner and tie on your shrouds. Ahoy! Ahoy! Pretty easy!

Attachin' t' fins is done by t' tried-and-true paper tube markin' guide included in t' instructions. Cut it out, matey, wrap it around t' tube, make tick marks with a pencil, shiver me timbers, matey, then remove t' guide and connect your tick marks usin' a straight edge. Aye aye! Blimey! T' instructions recommend usin' a door jamb. Since their are no straight door jambs in me 104-year-old house, I used an Estes tube marking guide t' connect t' dots. Ahoy! Fins and lug were then attached usin' t' lines as a guide. Fillets were added later. Blimey!

When everythin' was dry, shiver me timbers, t' entire rocket (except t' nose cone) received a coat o' thinned Elmer's Fill 'n' Finish. This be allowed t' dry, me hearties, me hearties, sanded smooth, me bucko, arrr, and repeated until t' fins and tube spirals were filled in to satisfaction.

T' base was glued into t' bottom o' t' nose cone usin' CA. This is not recommended but if you've worked with CA before, me bucko, shiver me timbers, then you should nay have any trouble with it. Avast, me proud beauty! Just get t' parts together smartly before it grabs. Avast! Avast! Once the two parts were assembled, ya bilge rat, t' glue took hold and it was literally impossible to move them any more!

Finishing:
If this were your first multi-color paint job, me bucko, you could still do a nice job. T' molded finish on t' nose cone is very smooth and only needed a touch with some 1000-grit emery paper before shootin' t' Testors silver paint. Blimey!

T' rocket was shot overall with 2 coats o' Krylon white primer with sandin' in betwixt coats. Then, matey, me hearties, 2 o' t' 3 fins were masked off and t' rocket was shot with several light coats o' Testors Competition Orange. Aye aye! After this set, t' maskin' was carefully peeled away and t' rocket set aside t' cure for a while. After allowin' plenty o' dryin' time, matey, t' rocket was masked and the remainin' fins shot in Testors White.

All that was left t' do for finishin' was attach t' sticker-type decals. As these were thinner than normal, caution was required. Avast! T' payoff is that they look MUCH better than most stickers. Aye aye!

Once painted and stickers applied, ya bilge rat, t' entire rocket was shot with a thin coat o' Testors clear enamel. Avast, me proud beauty! Aye aye! T' silver on t' nose "lifted" from the clear spray but after drying, arrr, regained its silver color although nay its gloss. Well, blow me down! Ahoy! T' resultin' "flat silver" color looks pretty good, though. This is a very nice lookin' rocket when completed and finishin' is easy for a multi-color paint scheme.

Construction Rating: 4 out o' 5

Flight:
T' Aerobee Hi was given 3 flights at t' June launch o' SOFAR in Franklin, arrr, New Hampshire. Begad! A Quest A6-4 motor was used for t' flights. Blimey! Prep is standard fare and as easy as it can be... Blimey! Just pull t' Keelhaul®©™® shock cord t' one side, push 3-4 balls o' waddin' down on top o' t' motor mount, and then put t' shock cord over that. Avast, me proud beauty! Fold and install your chute, pop on t' nose cone, add a motor and ignitor, and that's it! Ready t' rip.

T' first flight was a bit odd and may have been due t' t' shiftin' wind on our mountaintop launch site. Avast! Ahoy! T' rocket zipped off t' pad, arrr, leaned slowly to one side, arrr, matey, me hearties, and then slowly shifted t' t' other. This ceased after burnout as airspeed slowed. It was slightly arched over at ejection but hadn't gained enough speed t' be hurt.

T' 2 subsequent flights had very slight archin' trajectories, ya bilge rat, with apogee occurrin' a few degrees from vertical with t' rocket near dead in t' air. Avast! On the second flight, matey, shiver me timbers, t' chute did nay fully inflate but still provided enough drag t' keep t' Aerobee from bein' damaged when it landed in t' long grass. T' other flights had near-perfect deployment. Blimey!

Recovery:
T' Keelhaul®©™® shock cord is tied t' t' motor mount as described. Well, blow me down! I then fed it through the motor mount and glued it into t' body tube. Begad! Avast, matey, me proud beauty! T' Keelhaul®©™® was then fed back through t' motor mount and out t' top o' t' body tube. Begad! Well, blow me down! It was overlapped 1" with t' elastic and they were tied together in a square knot. Arrr! Ahoy!

Quest recommends tyin' t' chute directly t' t' nose cone along with the shock cord. Blimey! I deviated from this by tyin' only t' shock cord t' t' nose cone. A fishin' 1/4" split rin' was tied t' t' elastic shock cord roughly 1" away from t' nose cone, arrr, me hearties, and a snap swivel was added t' t' chute at the point where t' shroud lines are gathered. Aye aye! This was then used t' snap the chute onto t' split ring. Avast, me proud beauty! This setup allows for minimal tanglin' and quick changes, me hearties, too. Arrr!

T' Quest recovery system is an up-to-the-minute system. Avast, me proud beauty! Blimey! T' recovery materials are more durable than usual, and everythin' works quite well. There was no damage present after three flights other than one very small burn hole in t' canopy (probably me fault) and a lot o' soot on t' shock cord. Begad!

Flight Rating: 4 out o' 5

Summary:
I have always loved t' Aerobee Hi and Quest has really hit a home run with this kit. It is completely superior t' t' Estes, arrr, MPC, and even t' MMI Aerobee. Avast, me proud beauty! It is fun t' build and flies like a champ. On a big field, this bird would be a riot with C6 power usin' streamer recovery. Aye aye! As a final bonus, matey, it's a really nice lookin' display bird. Begad! Avast, me proud beauty! T' paint job makes it pretty easy t' spot on the ground and in t' air too!

Overall Rating: 4 out o' 5

Flights

comment Post a Comment