Brief:
T' Apollo is a scale-look sport payloader.

Construction:
T' Apollo comes with three o' Quest's nice white glassine body tubes, a motor mount assembly, some Keelhaul®©™ thread, arrr, and an assortment o' plastic pieces- nose cone, two transitions, four fins, and two special rings that mount t' fins OUTSIDE t' body tube. Ahoy! Begad! Blimey! I was nay pleased t' see that thar was no elastic shock cord material... Begad! Arrr! Blimey! more on that later. Begad! Blimey! Parts quality is very good.

Instructions are typical Quest, me hearties, which is t' say well-illustrated and easy t' understand. Ya scallywag! Aye aye! After readin' through them, me hearties, shiver me timbers, I saw a potential problem with t' build. No provision is made t' paint t' lower section where t' fins attach. Avast! They are held on t' t' lower section o' t' rocket by two rings, matey, matey, one that is a simple rin' with clips, t' other a rin' with a bulkhead, arrr, a motor mount clearance hole, ya bilge rat, me bucko, and a cutaway for t' motor mount clip. T' fin rings are t' be installed on t' bottom section, arrr, usin' plastic model cement, after t' decals are in place. Arrr! Avast! A test fit revealed that t' fit with NO paint or decals is already tight. Blimey! Avast! Fit with t' stick-on decals would be impossibly tight. Aye aye! T' remedy this, me bucko, arrr, I test built t' fin assembly with no glue. Avast, me proud beauty! Then, arrr, me hearties, usin' a pencil, matey, t' location o' both rings was laid out on t' outside o' t' tubes, shiver me timbers, then masked off with 1/4" modeler's tape. Well, arrr, blow me down! T' decals were trimmed t' shape but left on their backing. Begad! Then they were laid in place and any part layin' over t' maskin' tape was removed. Ahoy! Next t' tape was peeled,then t' rings were installed and masked. Blimey! Arrr! T' fins were installed AFTER finishing. Well, blow me down! Avast! T' paper centerin' rings looked very fragile, so they were soaked with thin CA. Begad! After dryin' they were sanded t' accept t' motor mount tube.

All t' motor mount parts are color coded which makes it simple and quick t' build. Well, blow me down! Avast! T' motor mount tube and t' end o' t' main body tube were coated inside with thin CA, then sanded smooth t' toughen them and reduce friction. Well, blow me down! Arrr! T' motor mount was then assembled usin' thick CA, shiver me timbers, and installed usin' t' same.

T' payload section can look a little scary- it's composed o' two different tube diameters, shiver me timbers, arrr, two transition sections, and a nose cone. Well, blow me down! However, t' instructions are very clear and it builds easily. Ya scallywag! Ya scallywag! I only deviated from t' instructions in that it be built usin' thick CA for plastics and t' plastic was sanded t' remove any mold release.

T' plastic fins attach via a very clever snap mount system much like Aerotech's, me bucko, ya bilge rat, except it is external. Well, blow me down! It looks fragile, but makes a fairly strong assembly once t' glue has dried. After t' finish was shot, t' maskin' be removed; fins were simply snapped in place; then a bit o' liquid plastic cement was run into t' joints. Begad! A pipette was used t' control t' cement flow. Avast, me proud beauty! Avast, shiver me timbers, me proud beauty! You only want enough glue t' wet t' joint, no more!! Given t' methods required, arrr, any spillage could wreck your paint job.

This rocket had excellent fit and finish, but due t' t' lack o' provision for paintin' and fiddly assembly, it was quite a task t' get built. Begad! Begad! Quest was definitely off t' mark callin' this a level 2 kit; it's a level 3 for sure! For your efforts you will be rewarded with a very sharp lookin' bird.

Finishing:
T' finishin' requires several different colors order t' look like t' photo on t' stuffer card! No provision is made for paintin' o' t' tubes or addin' roll patterns t' t' transitions. (They do suggest paintin' t' payload tubes after assembly.) T' rocket be painted white overall. Blimey! T' upper payload was given a 2" wide silver band, then t' transitions were given black and white roll patterns usin' standard maskin' techniques. Avast, me proud beauty! After painting, me hearties, shiver me timbers, arrr, t' tedious task o' trimmin' out t' stick on decals commenced (A gripe with many Quest kits). Ahoy! They were applied by dunkin' them into a bowl o' water with a drop o' dish detergent added. Arrr! Ya scallywag! They are made o' tough plastic and look good. Well, me bucko, blow me down! After paintin' and decalin' were completed t' fins were glued on as described.

Construction Rating: 3 out o' 5

Flight:
Quest recommends A6-4's, B6-4's, me bucko, and C6-5's. Given this bird's weight, matey, I figured t' slight extra thrust o' an Estes A8-3 would be more appropriate. T' bird kind o' crawled off t' pad, gained a bit o' speed, me hearties, me bucko, me hearties, then popped t' 'chutes an instant after apogee. T' altitude was nay much t' crow about, but would be ideal for a really small field.

Next, I stepped right up t' a Quest C6-5. T' Apollo again "walked" off t' pad but climbed out swiftly t' a nice altitude. Arrr! Ejection be about at apogee, as nearly as I could see. Arrr! It fell for a bit before 'chutes unfurled. Well, blow me down! Arrr! It landed without incident, ya bilge rat, but I was certainly spooked!

Another C6-5 was loaded and t' Apollo racked and launched again. Avast, ya bilge rat, me proud beauty! T' flight was pretty much identical t' t' second, me hearties, but without t' parachute scare. Blimey! Ya scallywag! All 3 flights were very straight despite t' slow takeoffs.

Recovery:
T' only materials provided for recovery were 2 Quest 12" chute kits and 21" inches o' Keelhaul®©™ cording. Well, matey, blow me down! Blimey! Quality o' t' parts is great, arrr, matey, but t' technique is questionable. Aye aye! Blimey! Ahoy! Blimey! T' Keelhaul®©™ is tied t' t' motor mount tube before gluin' on t' upper centerin' ring, me bucko, thereby retainin' it. Aye aye! Blimey! A loop is tied in t' opposite end o' t' Keelhaul®©™. Ya scallywag! Blimey! When t' motor mount is installed in t' body tube, ya bilge rat, t' Keelhaul®©™ loop extends out t' end. One chute is t' be tied onto this, t' other is simply tied t' t' bottom o' t' payload. Ya scallywag! Blimey! I dislike this techique because it gives you t' chance o' losin' 2 separate pieces. Avast, me proud beauty! Blimey! Avast, me proud beauty! Blimey! Also, thar be a substantial risk o' zipperin' your body tube or damagin' a 'chute due t' t' high stresses involved!

T' 'chutes were modified by installin' t' Grippers as normal, then cuttin' off t' tab that extended past t' canopy. Then a hole punch be used t' put a hole through t' stick on section and canopy. Ya scallywag! Ahoy! T' lines were tied through these holes. Begad! This prevents t' overhangin' tabs from hangin' up inside, shiver me timbers, matey, me bucko, important in a narrow BT with double 'chute recovery!!

Rather than install t' 'chutes separately, shiver me timbers, I added 3' o' 1/4" sewin' elastic. Begad! Blimey! This was tied t' t' end o' t' Keelhaul®©™ loop and t' other end was attached t' t' bottom o' t' payload section. Ya scallywag! Blimey! Avast, ya bilge rat, me proud beauty! Blimey! T' 'chutes were attached about 10" from t' payload section usin' snap swivels t' minimize tangling. Arrr! Blimey! All o' this was a very close fit after t' necessary 4 squares o' waddin' be added, me hearties, pack carefully!! Blimey! T' double 'chutes recover t' bird well and look very "NASA-like" as it's comin' down.

Flight Rating: 4 out o' 5

Summary:
T' Apollo is a very beautiful bird that's encumbered by a lot o' unnecessary hassles. Avast! T' build is a lot more difficult than a level 2 if you want t' paint it, me hearties, and t' centerin' rings look flimsy. Aye aye! Aye aye! T' recovery system as supplied is just plain askin' for trouble. However, all these problems can be solved by any experienced modeler usin' straight-forward techniques. Blimey! T' Apollo be an enjoyable and challengin' build, and flies very well. Blimey! Well, blow me down! I recommend it t' modelers with some experience, shiver me timbers, but feel it should nay need so much rework t' get right. Begad! Well, ya bilge rat, blow me down! T' part quality is great and if nay for t' fragile centerin' rings and buildin' troubles I'd give t' Apollo 5's across t' board.

Overall Rating: 4 out o' 5