Brief:
Next week, shiver me timbers, me bucko, me club is goin' t' have an informal 13mm duration competition. I never win these things, shiver me timbers, but I do like to take part. Begad! With only a week t' go, I realized that I didn't have anythin' ready t' enter and started lookin' through the inventory. Avast, me proud beauty! I found t' Red Alert. It seemed light and would go pretty high on an A despite t' draggy nose cone. Besides, ya bilge rat, it was near t' front o' one o' t' pegs and that made it easy t' choose since I recently reorganized and hung everythin' up.

T' Red Alert comes with a streamer and I like streamers but for this one, shiver me timbers, me hearties, I will probably try t' stuff a parachute in it t' get t' maximum hang time.

Construction:
Construction on this one started out by couplin' t' 2 BT-5 tubes. There be a longer one and a shorter one and they were joined with an insert coupler and yellow glue.

T' motor mount came next. T' coupler for t' 2 tubes acts as a thrust rin' and a slit be cut just aft o' it to accept t' engine hook. Well, blow me down! A plastic band be then slipped around t' tube and t' hook t' hold it in place and was secured with yellow glue.

T' three fins came on a die-cut balsa sheet. Avast! T' cut lines were so fine that I had a very difficult time even seein' them. Aye aye! I found them by gently flexin' t' balsa and lookin' for t' cracks t' open up. Ya scallywag! I would then give the lines a little encouragement with an X-Acto knife and do it again. Avast, me proud beauty! Eventually I got them out.

T' fins were stacked and sanded and then t' leading, me bucko, outer and trailin' edges were sanded round. A slot t' fit around t' engine hook band also had t' be filed.

Unlike t' fins, matey, t' launch lug standoff is nay provided as die cut. Avast! Instead, I be instructed t' cut two pieces of scrap t' t' given dimensions and glue them together. Ahoy! I stacked and sanded them first and then put them together with yellow glue. Begad! They needed t' be made uniform after they dried.

T' distinctive nosecone needed only t' have t' screw eye inserted and glued into place.

T' kit comes with a wraparound fin markin' guide. It was used t' transfer fin, engine hook, and launch lug lines to t' BT and then t' lines were extended. Ahoy! Avast! T' fins were glued in place usin' a double glue joint and yellow glue.

After t' fins were in place, me hearties, t' filletin' process began. Blimey! Begad! That gave me time t' work on a few other things. Begad! Avast, ya bilge rat, me proud beauty! As I mentioned above, t' launch lug standoff was laminated together with 2 pieces o' scrap. When it had dried, I sanded it square and then glued on t' lug.

When t' lug was safely glued t' t' standoff, shiver me timbers, I glued t' standoff t' t' BT along t' line given by t' marking guide.

Based on some advice from TRF and me experience with t' ASP Hangtime, matey, matey, I decided t' use an external shock cord. Accordingly, a length o' Keelhaul®©™® was glued into t' root edge o' one o' t' fillets. Ya scallywag! A notch t' accommodate t' Keelhaul®©™® was also filed into t' top end o' t' BT.

PROs: Simple build.

CONs: None, except for t' default shock cord t' be dealt with later.

Finishing:
I test fit everythin' together and then started applyin' balsa fillercoat. Begad! T' rocket took only two coats before bein' judged ready for sanding.

T' sandin' was rudimentary and then t' rocket be primed with Kilz. Blimey! Another sandin' saw it ready for being painted red. Arrr! Avast, me proud beauty! I put tape on t' Keelhaul®©™® to keep it from gettin' painted and then set it up in t' booth and shot it with Rustoleum Red. Avast! A day later, I gave it another coat o' red and, ya bilge rat, me bucko, when it be dry, shiver me timbers, arrr, peeled t' tape off o' t' shock cord. Avast! Avast, me proud beauty! After that, thar be just a simple, single holographic sticker t' apply. Aye aye!

T' original purpose o' t' sticker be t' hold t' rubber shock cord after it had been fed through a slit in the BT. Begad! Ya scallywag! I used mine just for decoration. It turns out that t' sticker was nay long enough t' go all t' way around t' BT. This hacked me off at first, shiver me timbers, but I then realized that t' gap be t' same size as t' launch lug standoff. Ahoy! It made sense.

PROs: Easy.

CONs: I still don't like stickers, shiver me timbers, even if it makes sense on this rocket.

Construction Rating: 3 out o' 5

Flight:
T' day o' t' competition dawned and I prepped t' rocket with an A3-4T. It actually looked kind o' cool sittin' on the pad. Blimey! When all be clear, ya bilge rat, it launched, me hearties, me hearties, flew straight, shiver me timbers, and deployed at apogee. Ahoy! Begad! I be worried about t' tightly packed chute, me hearties, but it deployed.

For flight, this is a nice one. Avast, shiver me timbers, me proud beauty! For hang time, its mediocre at best. I got 50 seconds. Begad! Arrr! Still, it was good enough to come in second!

PROs: This is a good performer, ya bilge rat, ya bilge rat, even with t' drag inducin' nosecone.

CONs: It's small enough t' drift far and be easily lost.

Recovery:
As noted in t' build section, matey, me hearties, matey, I did nay follow instruction as t' t' shock cord technique. Well, blow me down! What is provided for in the kit is t' make a slit near t' forward end o' t' BT and then feed through that slit a pathetically short length of glorified rubber band. Ahoy! T' "decal" is then used t' secure t' rubber band in place. T' other end is tied to the NC and a short piece o' plastic flaggin' is tied t' t' rubber band t' act as a streamer. Arrr! It is me considered opinion that this model is small enough and light enough t' recover as a tumble. Aye aye! Well, blow me down! T' streamer will, arrr, however, aid in spottin' it in t' air.

I substituted a 12" plastic parachute from Dr Zooch. Begad! Its nay easy t' stuff into t' small tube but it did accomplish me purposes.

PROs: Nay much is needed.

CONs: Shock cord method, rubber too short, rubber too weak, arrr, and streamer too short.

I would have given this another point based on t' flight were it nay for t' standard recovery system.

Flight Rating: 3 out o' 5

Summary:
T' distinctive nose cone o' this one makes it stand out from other small rockets o' similar stature. It is easy to assemble and performs well. Avast! Blimey! I don't like t' standard recovery system, shiver me timbers, arrr, but I am very opinionated in that regard.

Overall Rating: 3 out o' 5