Brief:
This is your basic high power rocket. It would be great for L1 or L2 certification attempts.

Construction:
It came with a 36 inch body tube and an 18 inch payload bay, me bucko, t' fins are 1/8" Baltic birch, me bucko, t' centerin' rings are fiberboard but once you have a layer o' 15 minute epoxy on thar good and strong, t' motor tube be a 38mm and t' parachute is an orange 36 inch parachute.

T' way t' instructions tell you t' assemble t' motor mount wouldn't work so I set t' instructions aside and built t' rocket without them. Ya scallywag! Ya scallywag! I first began by cuttin' out t' fin slots. Ahoy! Arrr! T' fin slots were already precut but nay all t' way. Ahoy! Avast, me proud beauty! Then I began work on t' motor mount I began by epoxyin' t' notched centerin' rin' at t' top o' t' motor mount and let that cure. Blimey! Then after it dried, I glued t' second centerin' rin' on. Aye aye! I put t' motor mount assembly in and tacked t' fins in place with some CA and let them dry. Then I pulled t' motor mount assembly out and put epoxy fillets on t' motor tube and fin tabs. Aye aye! I also covered t' motor tube in epoxy while doin' this t' make sure t' bond be extra strong and make t' motor tube stronger. Ahoy! I also epoxied t' third centerin' rin' onto t' back. Blimey! After doin' all that, matey, I slid t' 3/8" nylon strap through t' notched centerin' at t' top like on PML kits and then epoxied t' piston strap t' t' motor tube. Arrr! I folded up t' shock cord and put it into t' motor tube and epoxied t' motor mount assembly into t' BT. Begad! Since t' slots went all t' way t' t' end o' t' BT, me hearties, I used rubber bands t' prevent t' BT from spreadin' out while epoxyin' t' BT t' t' aft centerin' ring. Blimey! Aye aye! I put t' epoxy fillets on t' outside and t' booster be complete.

Next came t' payload section, which started with epoxyin' t' eye bolt into t' bulkplate. Begad! Then I epoxied t' bulkplate into t' coupler for t' payload pay. Ya scallywag! T' last step was t' epoxy on t' 3/8" copper launch lugs on.

Overall this rocket was fairly easy t' build and would be good for a second or third mid/high power rocket. Arrr! Blimey! Well, matey, blow me down! Blimey! There are no cons for construction o' this rocket.

Finishing:
I try t' do a different paint job from everyone else. Arrr! Avast, me proud beauty! Blimey! How often do you see an all green rocket? Rarely. So I decided t' paint me Performer all green. Avast, me proud beauty! Begad! Blimey! T' finishin' be easy. I put two coats on sandable primer and then I put on about 6 t' 7 coats o' green until it was perfectly glossy smooth. Ahoy! There are no cons about finishin' this rocket besides it takin' a lot o' paint.

Construction Rating: 5 out o' 5

Flight:
I choose t' I154J for t' first flight o' this rocket. Arrr! Ya scallywag! It was an awesome and perfectly straight flight t' about 3500 feet. It was also t' only all green rocket at XPRS IV 2005, I think. Avast! For t' next flight I plan on usin' a H148 t' test dual deployment, then an I195, I366, matey, I300, and I284.

Recovery:
For only a 36 inch parachute and launchin' in fairly windy conditions, ya bilge rat, t' rocket drifted about 3/4 o' mile. Avast, ya bilge rat, me proud beauty! I would say that t' parachute is perfectly sized for this rocket and brings back t' rocket nice and safely.

Flight Rating: 5 out o' 5

Summary:
This is a great rocket. Aye aye! Aye aye! If you are on a tight budget and lookin' for a fairly good size rocket, matey, then this be t' rocket for you.

Overall Rating: 5 out o' 5