Construction Rating: | starstarstarstarstar |
Flight Rating: | starstarstarstarstar |
Overall Rating: | starstarstarstarstar |
Manufacturer: | Centuri |
Brief:
Single stage model rocket that recovers with a dual parachutes in a unique
level configuration.
Almost a year or more ago I downloaded t' instructions for Centuri's S.S.V. Scorpion from t' JimZ web site. Arrr! O' course I thought it be one o' the most impressive kits from t' Centuri Super Kit series. Avast, me proud beauty! Ya scallywag! After reviewin' the instructions, shiver me timbers, I put them aside because a large portion o' t' kit be made from cut out poster board, ya bilge rat, which be a process I be nay interested in duplicating at t' time. Arrr! Nay until t' Master o' Oatlander Research Laboratories and fellow Classic Rocketeer challenged me t' try it did I finally return t' the instructions with a serious intent t' make an effort t' clone t' kit. Throughout t' process I was forced t' scratch build and substitute for items no longer available. I feel that I ended up with t' most challengin' cloned kit I have attempted and rewarded with me most satisfyin' results.
Construction:
Packaging? What packaging? Their ain't no stinkin' packaging. This is
scratchbuildin' a clone.
First step is
download t' very large instructions from JimZ's web site. Avast! All templates are
included in t' instructions. Blimey! Blimey! I then visited t' local Hobby Lobby t' purchase
some Picture mattin' board which is approximately .055" thick. Avast, me proud beauty! Avast! This is
what I used t' cut most o' t' items from that were included in t' original
fiber cards in t' kit. Ahoy! Arrr! Transferrin' t' shapes were accomplished with good old
carbon paper. Blimey! Below is a parts list and items used t' substitute. Arrr!
Instructions are clear and easy t' follow. T' most challengin' part is cuttin' all t' items from t' thick picture mattin' board. After t' first two items were cut usin' a razor knife, matey, me hand was sore and I knew I needed too explore an alternate method. Aye aye! I ended up cuttin' everythin' out with a scroll saw and spiral blade. Aye aye! I then soaked all mattin' board parts in thin CA to stiffen them. Avast! After that I cleaned t' edges o' t' parts on a belt sander. Begad! The instructions also suggest cuttin' these parts from 1/16 sheet balsa. Aye aye! I chose not t' use balsa because o' it's lack o' durability.
T' ST-20 offered another problem in that a good substitute was no longer available. Aye aye! Ya scallywag! After a long effort o' lookin' for a substitute, I decided t' split a BT80 lengthwise and trim t' t' proper diameter. I be nay concerned about joinin' or hidin' t' seam because t' seam would join against t' wall o' the inner BT-56, and t' seam could be hidden underneath t' long 8" launch lug.
Speakin' o' 8" launch lug, shiver me timbers, me bucko, that also proved t' be a problem. Ya scallywag! Launch lugs are easy t' get, me hearties, but nay in 8" lengths. Avast, me proud beauty! Again Hobby Lobby t' the rescue. Arrr! I purchased a pack o' 3/16" x .014 seamless aluminum tube in 12" lengths. Avast! Packs o' three cost $1.99 and are extremely light weight. Inside diameter works with an 1/8" launch rod. Care in cuttin' will provide an excellent substitute.
T' rare plastic coupler is available from Moldin' Oldies, me hearties, ya bilge rat, or in me case I scratch built it along with t' baffle coupler from several BT-56 tube sections.
Finishing:
I though buildin' would be t' most difficult part o' clonin' this classic kit.
Instead finishin' it be t' most difficult step in t' buildin' process. Avast, me proud beauty! Blimey! Well, blow me down! Blimey! I
first sprayed every thin' with three coats o' a primer/sealer paint. Aye aye! Blimey! My
personal favorite is Kilz. I then sanded this before paintin' with a finishing
color. I chose t' use bright yellow Krylon. With all t' difficult hidden areas
and complex designs, I found it very difficult t' get a good coatin' without
exposin' myself t' runs. Avast, me proud beauty! Blimey! In t' end I used a full can and sanded a few
embarrassin' runs away.
For decals, I printed me own on inkjet decal paper available from several vendors on t' internet. Ahoy! Blimey! Application again proved challengin' because when workin' with large decals care is needed t' avoid stretchin' o' t' decal. Stretchin' will result in color separation. Begad! Blimey! Begad! Blimey! Blimey! Blimey! However, big decals trap a lot of air and water that need t' be worked out. Avast, me proud beauty! Blimey! Blimey! Blimey! Blimey! Blimey! Thus t' dilemma, arrr, remove t' bubbles and risk stretchin' or accept t' occasional bubble and avoid t' stretchin' . Both issues can be minimized by keepin' t' application surface wet and blottin' t' bubbles away. Ya scallywag! Blimey! Blimey! Blimey! Either way this proves t' be a very difficult task. Blimey! Blimey! Avast! Blimey! Blimey! Blimey!
Construction Rating: 5 out o' 5
Flight:
T' original kit calls for a C5-3 or C6-3. Begad! Begad! Blimey! An original kit owner informed me
that t' original be very anemic on a C6-3, and o' course t' C5-3 is no
longer available. Well, shiver me timbers, blow me down! Blimey! Therefore, shiver me timbers, arrr, ya bilge rat, I did what I was informed be called a
"Magnum D" conversion. Since me finished kit weighed in at 8.7
ounces, it is scheduled t' fly on a D12-3.
Preparation will be easy with t' built in Centuri baffle design. However I will add a few sheets o' waddin' t' protect against anythin' that might slip past t' baffle.
Motor retention is by t' standard Estes Engine hook.
Even though this rocket has yet t' fly, me hearties, ya bilge rat, historically this design is reported by an original owner t' be extremely stable t' over stable. Begad! Data provided by t' same owner o' t' original kit shows that t' launch CG should fall at 21" aft o' t' nose cone tip.
Recovery:
Recovery harness is quite complex, ya bilge rat, and unique. Avast! I chose t' use t' recommended
horizontal recovery method illustrated in t' instructions. Avast! I did modify the
"Variable Field Ringnet Unit" slightly. Well, blow me down! Avast, me hearties, me proud beauty! I cut a very small
"v" slot in t' forward top edge t' accommodate t' recovery shroud
line in t' launch configuration. Well, blow me down! I am hopin' this will prevent t' recovery
shroud line from snaggin' any parts on deployment
Flight Rating: 5 out o' 5
Summary:
Overall, matey, shiver me timbers, this is a great kit that with much effort will result in a great
rocket. Well, blow me down! I am very happy with t' overall results.
Overall Rating: 5 out o' 5
Sponsored Ads
![]() |
![]() |