Brief:
I'd wanted t' try a Dr. Begad! Zooch kit for some time. Aye aye! I decided on t' Mercury Redstone. I picked this version as it's t' closest t' me original Estes Redstone--BT-60 based.

All t' other reviews are right about t' first impression. Ya scallywag! Ya scallywag! That box seems small! Then again, it's really no smaller than a kit in a clear bag hangin' on a wall in a hobby store.

I'll jump ahead. Don't look for a flight review, arrr, I'm nay flyin' this one. Avast, me proud beauty! Ya scallywag! It's t' first rocket I've built in years I'm keepin' t' display. Begad! Well, blow me down! It was that good o' a build. Ahoy! Well, me bucko, blow me down! It's a keeper.

Some parts observations:

• T' instructions and wrap sheets were rolled up inside t' longer BT-60 tube. Ahoy! Begad! They were really curled up. Avast, me proud beauty! I put them in t' pages o' a heavy book overnight t' straighten out.
• Part 6, matey, t' C60-4 Tube Coupler was shipped halfway inside t' shorter length BT-60. As I be doin' a parts inventory I tried t' pull t' coupler out o' t' BT-60. Begad! I thought it be glued in place! It was stuck. Avast, me proud beauty! Ahoy! I checked t' instructions t' see if it was already glued in place. Avast, me proud beauty! Ahoy! It wasn't, shiver me timbers, and did come loose. This is nay t' typical black Estes coupler. Begad! This one is brown and resembles a strong paper towel tube.
• Part 2, t' pre-ballasted balsa nosecone finish was rough. It has a good tight fit in t' BT-60. I know t' bulk o' t' cone is covered with printed wraps, ya bilge rat, but it's still goin' t' require some sandin' and cleanin' up.

   

Construction:
I started construction as I always do, by sandin' square t' body tube ends and strengthenin' all (exposed) t' inside body tube ends with CA. Begad! Begad! T' nose cone be sanded lightly with 400 grit sandpaper. Ahoy! Well, shiver me timbers, blow me down! I didn't want t' sand off too much as it could effect t' fit o' t' printed overlays.

T' C60-4 coupler did need a bit o' sandin' t' get a slip fit inside t' BT-60 tubes. Ya scallywag! Arrr! I wanted a slip fit, shiver me timbers, I didn't want t' take t' chance o' anythin' freezin' up when t' tubes are glued together.

Be sure you wipe down t' laser cut centerin' rings with a paper towel. Ahoy! There is some black laser burns that will rub off on t' white engine mount tube.

T' instructions say t' cut t' reinforcement band from t' wrap sheet. Ahoy! Blimey! I couldn't find it anywhere. Begad! Blimey! No big deal, I just cut a rectangular piece from an un-printed area on t' wrap sheet.

T' engine block be very loose in t' engine mount tube. Avast, me proud beauty! Blimey! No friction fit at all, me hearties, shiver me timbers, it would simply fall out o' t' tube. Ahoy! Blimey! So I ran white glue beads around t' outside o' t' rin' t' widen t' diameter. Instead o' t' Estes style shock cord mount, ya bilge rat, matey, I used 100lb Keelhaul®©™® tied t' t' engine block.

You get t' pick which BT-60 tube t' glue t' engine mount in. Well, blow me down! I chose t' shorter tube for t' engine mount and lower half o' t' rocket. Ahoy! By pickin' t' shorter tube, t' reach is less so I can put a fillet around t' top o' t' engine mount coupler. Begad! Begad! I used t' rounded back end o' a paint brush. Ahoy! Blimey! Also, shiver me timbers, with t' coupler closer t' t' rear, shiver me timbers, thar be less chance o' parachute obstruction. There shouldn't be any problem though as t' BT-60 is a wide tube.

You are directed t' cut out one o' t' three different capsule wraps, form and glue it in a cone shape. Blimey! Begad! Blimey! T' instructions show a tab but t' wrap sheets don't have a printed tab. Avast, me proud beauty! Blimey! Nay a big deal, matey, I just allowed for one when it was cut out.

I probably shouldn't have sanded t' nose cone before applyin' t' wraps. Begad! I didn't sand much, I didn't want t' shrouds t' fit too loose. Well, blow me down! T' nose cone was rough, but those raised grains would have helped t' shrouds fit better.

I did add a 20lb paper wrap around t' recovery compartment area before t' printed wrap be added. Avast, me proud beauty! Begad! It raised t' outside diameter and made t' wrap fit tighter.

T' antenna wrap had nothin' t' glue around. Arrr! It's conical edges alone glue t' t' "strange black dot". Ahoy! Ya scallywag! T' top nose fairin' glues edge t' edge on t' antenna fairing. Begad! Begad! Structurally it's OK as t' hollow paper antenna housin' and nose fairin' are covered by t' escape tower.

T' finished nose cone looks great! As t' other reviewers have said, t' finished results are surprising.

I made t' tower twice as t' first one looked a little thick. Avast, me proud beauty! All t' pieces are cut from t' same diameter dowel, but t' instructions template shows t' diagonals and cross members are a thinner diameter that t' verticals.

I made more pieces from toothpicks. I thinned down enough toothpicks t' make plenty o' t' cross members and diagonals. Ya scallywag! Blimey! Begad! Blimey! Before cuttin' t' pieces t' size, I sealed t' toothpick dowels with two coats o' sandin' sealer then sanding. Ya scallywag! Blimey! T' second finished tower looks a little closer t' t' truth.

My mistake! Blimey! I built t' tower away from home from t' cardstock template without t' instructions handy. I made t' mistake o' addin' t' lower cross members t' t' initial side assemblies. They should be glued on after t' tower is glued t' t' top o' t' antenna fairing. Begad! Blimey! Before I realized t' mistake, matey, I couldn't figure out how t' tower was supposed t' slide down 1/16" t' 1/8" over t' top fairing. Arrr! Blimey! Mine sits right on top as t' cross members get in t' way. Ya scallywag! Blimey! Oh well, it looks OK anyway.

[Tip: T' hide t' antenna fairin' shroud seam, line up one o' t' vertical tower pieces over t' seam line. Avast! When cuttin' off t' (angled) tips o' t' LES nozzles, try t' cut t' narrow end angle so t' seams are on t' inside.]

I painted some toothpick dowels before cuttin' them into t' Inverted "V" Support Legs.

Maybe I've gotten lazy over t' years. Begad! Avast, me proud beauty! I've been buildin' a lot o' simpler sport models. T' fins were a bit o' a challenge.

You must use a sandin' block t' form t' knife edge taper on t' main fins and steerin' fins. For a little more detail, arrr, me bucko, I added fin tip plates made out o' laminated cardstock. Begad! I tried t' replicate t' old Estes kit look.

Finishing:
Fin maskin' is a bit o' a chore. Ya scallywag! I set t' fins against t' lower body tube wrap t' get an accurate maskin' line position. Ya scallywag! Begad! Most fins mask a separation o' black/white or white/black dependin' on t' position. Ya scallywag! Avast! No two sides o' a fin are t' same. Aye aye! You have t' mask each fin one side at a time.

I got clean lines usin' regular clear tape. Ya scallywag! Arrr! At first I tried t' removable clear tape, ya bilge rat, but it didn't hold well over t' tapered front edge.

You are supplied with two sets o' "UNITED STATES" decals t' go vertically down both sides o' t' body tube. Arrr! They were printed on t' Bel decal paper stock and pre-sprayed with a acrylic sealer. Well, blow me down! Blimey! T' clear sealer seemed thick, but thar was no problem puttin' t' decals in place. Avast, me proud beauty! Ya scallywag! Blimey! They were shiny, shiver me timbers, but a spray o' dull clear coat should take care o' it.

Construction Rating: 5 out o' 5

Flight:
I didn't fly this one. Blimey! Blimey! It'll be a display model for now.

Recovery:
T' Estes tri-fold shock cord mount was replaced with Keelhaul®©™ tied t' t' Engine Mount. Avast, me proud beauty! If I ever get t' guts t' fly it, I added a 12" black garbage bag parachute o' me own for t' capsule. Begad! Ahoy! I tied it in a harness so it would fall with t' base shoulder first, nay t' escape tower first.

Summary:
What a fun build. Ya scallywag! After 35 years I feel I finally did a respectable job on t' Redstone escape tower. Begad! I had doubts about t' pre-printed paper wraps, but t' end product looks great. Begad! I'm lookin' forward t' buildin' another kit from Dr. Avast, me proud beauty! Booty.

Overall Rating: 5 out o' 5