I was really enjoyin' me 24mm RMS system on me Nordic Rocketry Meanie and Ascender, arrr, as well as other rockets when I started gettin' t' "cluster" urge. Well, blow me down! Avast! I looked for 24mm cluster rockets and found very, very few. Ya scallywag! When I spotted t' THOY Snipe, me bucko, I jumped at it. THOY says "the Snipe is an easy t' build rocket with great eye appeal. Aye aye! This high performance sport rocket is capable o' achievin' high altitudes with a payload." T' payload I chose was t' Missile Work's RRC² deployment electronics. Ahoy! I also planned on usin' me Unique Rocketry IgniterMan home-dipped igniters. T' Snipe is 56" long and uses 2.6" diameter tubing. Begad! Blimey! It is designed t' use three 24mm motors t' push its 18 ounces into t' air and then recover with a 28" parachute.

T' Snipe consists o' two 2.6" paper-wound body tubes that coupled with t' plastic 13" long nose cone make up t' 56" length. T' three fins are are 1/8" plywood with a through-the-wall tab. Well, blow me down! Blimey! T' two centerin' rings and one bulkhead are also 1/8" plywood. Blimey! Both centerin' rings have t' cut-outs t' handle t' cluster o' three 24mm motor tubes. T' upper centerin' rin' has a 3/32" thick, shiver me timbers, 18.5" long steel cable already attached and a loop crimped t' attach t' 9' long, 1/2" wide shock cord. Avast! Avast! T' three 24mm motor tubes are just under 8" long. Begad! Avast! There is also a 1/4" launch lug and an eye-screw and nut for t' bulk head. Lastly thar be a pinkish in color, shiver me timbers, arrr, 28" rip-stop nylon parachute.

CONSTRUCTION:

T' instructions are short and simple t' follow. Avast, me proud beauty! Blimey! Blimey! Blimey! There are illustrations down t' right side with text instructions on t' left side. Avast, me proud beauty! Blimey! All instructions are included on both sides o' a single 8x11 sheet o' paper. Blimey! Blimey!

Assembly is very straight-forward and thar are only a couple o' tasks that require special attention. T' first be t' fit o' t' three 24mm motor tubes into t' centerin' rings once they are glued together. I found sandin' be necessary t' nay put too much stress on t' tubes. T' second is cuttin' t' slots for t' fins. Avast! Blimey! THOY has made this as easy as possible by pre-drawin' t' lines for both cuts per fin on t' body tube. Well, blow me down! Blimey! Begad! Blimey! Just take your time t' get nice cuts.

I had a couple o' buildin' disappointments with this rocket. Aye aye! Ya scallywag! One be that t' fins have only a 1/2" tab that is inserted through-the-wall. T' diagram in step #8, shows t' fins goin' all t' way t' t' joints betwixt t' motor mount tubes. Blimey! Arrr! T' second, me hearties, was that thar be no positive motor retention. This was very easily remedied by gettin' a #8 screw that be 3" long and cuttin' off t' head. I then epoxied t' screw in t' small center space created when t' three motor tubes are glued together. Then an appropriately sized washer and two nuts hold those motors right in place.

T' "great eye appeal", t' me, ya bilge rat, is due t' t' shape o' t' fins and t' long nose cone. Ya scallywag! Both make it impressive t' look at on t' pad.

I have consistent results for finishin' usin' Elmers' Light Spackle t' fill t' spirals, then several good coats o' Plasti-Kote primer. Ahoy! I then used a special "hammered look" paint from Rustoleum. This gave t' rocket a unique look. Avast, me proud beauty! I used a forest green "hammered" paint for t' bottom and a silver "hammered" paint for t' top. I then masked off a few green strips. T' kit does nay come with any decals.

Overall, me bucko, for CONSTRUCTION I would rate this kit 4 points. Avast! Avast, ya bilge rat, me proud beauty! T' quality o' t' parts are solid and t' cuts on t' fins were precision (not lazer either). Well, blow me down! Avast! T' instructions met t' needs and t' kit is actually very easy t' assemble. Aye aye! T' through-the-wall fins and motor retention fall a bit short.

FLIGHT/RECOVERY:

T' preparation o' this bird takes a bit o' time. Begad! I built three 24mm RMS motors usin' E18's without an ejection charge. T' recommended motors are three D12-3's, three E15-7's, shiver me timbers, matey, or three E30-7's.

Once t' motors were built and installed usin' IgniterMan home-dipped ignitors and then connected t' me Estes Command Controller, arrr, me bucko, t' Snipe be ready t' go. Aye aye! Blimey! I had installed t' Cannonball Works RRC² with dual deployment. It was wired and beepin' at launch. Avast, me proud beauty! Blimey! Ya scallywag! Blimey! After a much anticipated countdown, Varooom! Blimey! Up went t' Snipe on 3-E18's, all lightin' and givin' it a nice punch! Blimey!

Just before apogee, ya bilge rat, t' initial RRC² charge fired. Aye aye! Blimey! T' momentum o' t' ejection at t' mid-section also popped t' nose cone out o' t' upper section, thereby deployin' t' main chute. As I chased this across t' field, at about 300 feet I heard t' secondary channel discharge. Aye aye! Blimey! Then this rocket drifted into a tree, 60 feet up, where it stayed for four attempts over a 5 week period. Avast, me proud beauty! Blimey! I did finally get it back though.

After some touch up and replacin' t' payload section, ya bilge rat, t' Snipe was ready t' go. Begad! I really wanted t' have a successful flight usin' me RRC² and felt good about another attempt in me (rebuilt) cluster rocket. Begad! Avast, me proud beauty! I used three E18's again. This time I was usin' RocketFlite MagnaLite ignitors. Blimey! Again I armed t' RRC² and everythin' seemed ready. Arrr! Another excellent boost. This time t' main charge deployed perfectly at apogee. It fell on t' drogue until at 300 feet t' secondary charge blew t' nose cone off. Blimey! But guess who had moved t' main chute t' another rocket t' use? Yep, me!

With t' impact one fin popped off and t' tubin' be bent, me hearties, so thus retired t' Snipe (at least t' bottom half). Aye aye! Well, blow me down! Blimey! I have immediate bought another one because I enjoy t' looks and flights o' this bird so much.

For FLIGHT/RECOVERY, I would rate this kit 5 points. Despite me electronic bloopers, t' initial flight showed that recovery is fine on t' 28" parachute. Ya scallywag! Also, t' impact t' satisfaction when all three motors light makes t' Snipe have a little extra enjoyment.

T' size stands out a bit, t' fin shape is unique, and t' flights with all three motors burnin' on t' way up adds a new dimension t' 24mm flights. Avast! T' ease o' build also makes this a good kit for relatively new rocketeers. Avast! Avast, me proud beauty! There are nay many cluster rockets in t' market and this 24mm cluster is a winner!

I give t' kit an OVERALL ratin' o' 4 ½ points. Ahoy! Ahoy!