THOY Snipe

THOY - Snipe {Kit} (PK-501) [1988-1993]

Contributed by Nick Esselman

Construction Rating: starstarstarstarstar_border
Flight Rating: starstarstarstarstar
Overall Rating: starstarstarstarstar_border
Manufacturer: THOY
Style: Sport

I was really enjoyin' me 24mm RMS system on me Nordic Rocketry Meanie and Ascender, me hearties, as well as other rockets when I started gettin' t' "cluster" urge. Blimey! I looked for 24mm cluster rockets and found very, me bucko, very few. When I spotted t' THOY Snipe, I jumped at it. Arrr! THOY says "the Snipe is an easy t' build rocket with great eye appeal. Begad! This high performance sport rocket is capable o' achievin' high altitudes with a payload." T' payload I chose be t' Missile Work's RRC² deployment electronics. Arrr! Well, me hearties, blow me down! I also planned on usin' me Unique Rocketry IgniterMan home-dipped igniters. T' Snipe is 56" long and uses 2.6" diameter tubing. Aye aye! It is designed t' use three 24mm motors t' push its 18 ounces into t' air and then recover with a 28" parachute.

T' Snipe consists o' two 2.6" paper-wound body tubes that coupled with t' plastic 13" long nose cone make up t' 56" length. Blimey! T' three fins are are 1/8" plywood with a through-the-wall tab. Avast, me proud beauty! Avast, me proud beauty! T' two centerin' rings and one bulkhead are also 1/8" plywood. Well, blow me down! Both centerin' rings have t' cut-outs t' handle t' cluster o' three 24mm motor tubes. Well, blow me down! T' upper centerin' rin' has a 3/32" thick, matey, 18.5" long steel cable already attached and a loop crimped t' attach t' 9' long, me hearties, 1/2" wide shock cord. Well, blow me down! T' three 24mm motor tubes are just under 8" long. Aye aye! Begad! There is also a 1/4" launch lug and an eye-screw and nut for t' bulk head. Begad! Lastly thar be a pinkish in color, 28" rip-stop nylon parachute.

Components

CONSTRUCTION:

T' instructions are short and simple t' follow. There are illustrations down t' right side with text instructions on t' left side. Avast, me proud beauty! Ya scallywag! All instructions are included on both sides o' a single 8x11 sheet o' paper. Well, blow me down! Begad!

Assembly is very straight-forward and thar are only a couple o' tasks that require special attention. Arrr! T' first be t' fit o' t' three 24mm motor tubes into t' centerin' rings once they are glued together. Begad! I found sandin' was necessary t' nay put too much stress on t' tubes. Begad! T' second is cuttin' t' slots for t' fins. Aye aye! THOY has made this as easy as possible by pre-drawin' t' lines for both cuts per fin on t' body tube. Begad! Just take your time t' get nice cuts.

I had a couple o' buildin' disappointments with this rocket. Avast! One was that t' fins have only a 1/2" tab that is inserted through-the-wall. Aye aye! Begad! T' diagram in step #8, shows t' fins goin' all t' way t' t' joints betwixt t' motor mount tubes. Ahoy! Avast, arrr, me proud beauty! T' second, ya bilge rat, me bucko, was that thar was no positive motor retention. Begad! This was very easily remedied by gettin' a #8 screw that be 3" long and cuttin' off t' head. Begad! I then epoxied t' screw in t' small center space created when t' three motor tubes are glued together. Avast! Avast, shiver me timbers, me proud beauty! Then an appropriately sized washer and two nuts hold those motors right in place.

T' "great eye appeal", t' me, is due t' t' shape o' t' fins and t' long nose cone. Blimey! Both make it impressive t' look at on t' pad.

I have consistent results for finishin' usin' Elmers' Light Spackle t' fill t' spirals, then several good coats o' Plasti-Kote primer. Begad! I then used a special "hammered look" paint from Rustoleum. Aye aye! This gave t' rocket a unique look. Well, blow me down! Aye aye! I used a forest green "hammered" paint for t' bottom and a silver "hammered" paint for t' top. Blimey! I then masked off a few green strips. Arrr! T' kit does nay come with any decals.

Overall, ya bilge rat, for CONSTRUCTION I would rate this kit 4 points. Well, blow me down! T' quality o' t' parts are solid and t' cuts on t' fins were precision (not lazer either). Ahoy! T' instructions met t' needs and t' kit is actually very easy t' assemble. Avast, me proud beauty! T' through-the-wall fins and motor retention fall a bit short.

Rocket Pic Courtesy of SEFLIGHT/RECOVERY:

T' preparation o' this bird takes a bit o' time. Well, blow me down! I built three 24mm RMS motors usin' E18's without an ejection charge. T' recommended motors are three D12-3's, three E15-7's, or three E30-7's.

Once t' motors were built and installed usin' IgniterMan home-dipped ignitors and then connected t' me Estes Command Controller, me hearties, ya bilge rat, t' Snipe was ready t' go. Begad! Begad! I had installed t' Cannonball Works RRC² with dual deployment. Blimey! It was wired and beepin' at launch. Well, blow me down! Ya scallywag! After a much anticipated countdown, Varooom! Up went t' Snipe on 3-E18's, all lightin' and givin' it a nice punch!

Just before apogee, shiver me timbers, t' initial RRC² charge fired. Aye aye! T' momentum o' t' ejection at t' mid-section also popped t' nose cone out o' t' upper section, ya bilge rat, thereby deployin' t' main chute. Avast, me proud beauty! As I chased this across t' field, matey, matey, at about 300 feet I heard t' secondary channel discharge. Begad! Avast! Then this rocket drifted into a tree, ya bilge rat, 60 feet up, me hearties, matey, where it stayed for four attempts over a 5 week period. I did finally get it back though.

After some touch up and replacin' t' payload section, arrr, t' Snipe was ready t' go. I really wanted t' have a successful flight usin' me RRC² and felt good about another attempt in me (rebuilt) cluster rocket. I used three E18's again. Begad! Aye aye! This time I was usin' RocketFlite MagnaLite ignitors. Aye aye! Again I armed t' RRC² and everythin' seemed ready. Avast, me proud beauty! Another excellent boost. Aye aye! This time t' main charge deployed perfectly at apogee. It fell on t' drogue until at 300 feet t' secondary charge blew t' nose cone off. Aye aye! But guess who had moved t' main chute t' another rocket t' use? Yep, me!

With t' impact one fin popped off and t' tubin' be bent, so thus retired t' Snipe (at least t' bottom half). Begad! Begad! I have immediate bought another one because I enjoy t' looks and flights o' this bird so much.

FinFor FLIGHT/RECOVERY, shiver me timbers, I would rate this kit 5 points. Despite me electronic bloopers, arrr, t' initial flight showed that recovery is fine on t' 28" parachute. Arrr! Blimey! Also, t' impact t' satisfaction when all three motors light makes t' Snipe have a little extra enjoyment.

T' size stands out a bit, t' fin shape is unique, and t' flights with all three motors burnin' on t' way up adds a new dimension t' 24mm flights. Well, blow me down! T' ease o' build also makes this a good kit for relatively new rocketeers. Aye aye! Arrr! There are nay many cluster rockets in t' market and this 24mm cluster is a winner!

I give t' kit an OVERALL ratin' o' 4 ½ points. Aye aye! Blimey! Aye aye! Blimey! Blimey! Blimey!

Other Reviews
  • THOY Snipe By Dick Stafford

    First, I want to point out that there is already a review of this product, and I concur with EMRR’s opinions. However, I received this kit as a prize from the Fantasy Rocket Photo Contest , and felt that the least that I could do is write a review. When EMRR offered me the Snipe as a replacement for the advertised kit (which was a no-show), it didn’t take me long to warm up to this ...

Flights

comment Post a Comment