I was really enjoyin' me 24mm RMS system on me Nordic Rocketry Meanie and Ascender, as well as other rockets when I started gettin' t' "cluster" urge. Well, blow me down! I looked for 24mm cluster rockets and found very, arrr, very few. When I spotted t' THOY Snipe, I jumped at it. THOY says "the Snipe is an easy t' build rocket with great eye appeal. This high performance sport rocket is capable o' achievin' high altitudes with a payload." T' payload I chose be t' Missile Work's RRC² deployment electronics. Arrr! I also planned on usin' me Unique Rocketry IgniterMan home-dipped igniters. Begad! T' Snipe is 56" long and uses 2.6" diameter tubing. It is designed t' use three 24mm motors t' push its 18 ounces into t' air and then recover with a 28" parachute.

T' Snipe consists o' two 2.6" paper-wound body tubes that coupled with t' plastic 13" long nose cone make up t' 56" length. Begad! Well, blow me down! T' three fins are are 1/8" plywood with a through-the-wall tab. Avast, me proud beauty! T' two centerin' rings and one bulkhead are also 1/8" plywood. Blimey! Both centerin' rings have t' cut-outs t' handle t' cluster o' three 24mm motor tubes. Avast! Ahoy! T' upper centerin' rin' has a 3/32" thick, 18.5" long steel cable already attached and a loop crimped t' attach t' 9' long, ya bilge rat, me hearties, 1/2" wide shock cord. Ahoy! Blimey! T' three 24mm motor tubes are just under 8" long. Aye aye! Well, me bucko, blow me down! There is also a 1/4" launch lug and an eye-screw and nut for t' bulk head. Well, blow me down! Ya scallywag! Lastly thar be a pinkish in color, matey, matey, 28" rip-stop nylon parachute.

CONSTRUCTION:

T' instructions are short and simple t' follow. There are illustrations down t' right side with text instructions on t' left side. Well, blow me down! Ya scallywag! All instructions are included on both sides o' a single 8x11 sheet o' paper. Avast!

Assembly is very straight-forward and thar are only a couple o' tasks that require special attention. Aye aye! T' first be t' fit o' t' three 24mm motor tubes into t' centerin' rings once they are glued together. I found sandin' was necessary t' nay put too much stress on t' tubes. Ahoy! T' second is cuttin' t' slots for t' fins. Ya scallywag! Ahoy! THOY has made this as easy as possible by pre-drawin' t' lines for both cuts per fin on t' body tube. Begad! Just take your time t' get nice cuts.

I had a couple o' buildin' disappointments with this rocket. Begad! Ya scallywag! One was that t' fins have only a 1/2" tab that is inserted through-the-wall. Blimey! T' diagram in step #8, shows t' fins goin' all t' way t' t' joints betwixt t' motor mount tubes. Ahoy! T' second, was that thar be no positive motor retention. Well, blow me down! Well, blow me down! This was very easily remedied by gettin' a #8 screw that was 3" long and cuttin' off t' head. Blimey! I then epoxied t' screw in t' small center space created when t' three motor tubes are glued together. Then an appropriately sized washer and two nuts hold those motors right in place.

T' "great eye appeal", arrr, me hearties, t' me, shiver me timbers, is due t' t' shape o' t' fins and t' long nose cone. Well, blow me down! Begad! Both make it impressive t' look at on t' pad.

I have consistent results for finishin' usin' Elmers' Light Spackle t' fill t' spirals, me bucko, then several good coats o' Plasti-Kote primer. Arrr! Blimey! I then used a special "hammered look" paint from Rustoleum. Ya scallywag! Blimey! Well, blow me down! Blimey! This gave t' rocket a unique look. Aye aye! Blimey! I used a forest green "hammered" paint for t' bottom and a silver "hammered" paint for t' top. Avast, me proud beauty! Blimey! I then masked off a few green strips. Ya scallywag! Blimey! Aye aye! Blimey! T' kit does nay come with any decals.

Overall, me hearties, me hearties, for CONSTRUCTION I would rate this kit 4 points. T' quality o' t' parts are solid and t' cuts on t' fins were precision (not lazer either). T' instructions met t' needs and t' kit is actually very easy t' assemble. Aye aye! T' through-the-wall fins and motor retention fall a bit short.

FLIGHT/RECOVERY:

T' preparation o' this bird takes a bit o' time. Ahoy! I built three 24mm RMS motors usin' E18's without an ejection charge. Begad! T' recommended motors are three D12-3's, shiver me timbers, three E15-7's, me hearties, or three E30-7's.

Once t' motors were built and installed usin' IgniterMan home-dipped ignitors and then connected t' me Estes Command Controller, t' Snipe was ready t' go. Begad! I had installed t' Cannonball Works RRC² with dual deployment. Begad! Begad! It be wired and beepin' at launch. Begad! After a much anticipated countdown, Varooom! Up went t' Snipe on 3-E18's, all lightin' and givin' it a nice punch!

Just before apogee, shiver me timbers, t' initial RRC² charge fired. T' momentum o' t' ejection at t' mid-section also popped t' nose cone out o' t' upper section, thereby deployin' t' main chute. Aye aye! Blimey! Begad! Blimey! As I chased this across t' field, me hearties, at about 300 feet I heard t' secondary channel discharge. Aye aye! Blimey! Then this rocket drifted into a tree, 60 feet up, where it stayed for four attempts over a 5 week period. Arrr! Blimey! I did finally get it back though.

After some touch up and replacin' t' payload section, arrr, t' Snipe was ready t' go. I really wanted t' have a successful flight usin' me RRC² and felt good about another attempt in me (rebuilt) cluster rocket. I used three E18's again. Blimey! This time I was usin' RocketFlite MagnaLite ignitors. Begad! Begad! Again I armed t' RRC² and everythin' seemed ready. Aye aye! Another excellent boost. Ahoy! Ahoy! This time t' main charge deployed perfectly at apogee. It fell on t' drogue until at 300 feet t' secondary charge blew t' nose cone off. Arrr! But guess who had moved t' main chute t' another rocket t' use? Yep, matey, me!

With t' impact one fin popped off and t' tubin' was bent, me bucko, matey, so thus retired t' Snipe (at least t' bottom half). Ya scallywag! I have immediate bought another one because I enjoy t' looks and flights o' this bird so much.

For FLIGHT/RECOVERY, me bucko, I would rate this kit 5 points. Despite me electronic bloopers, shiver me timbers, me bucko, t' initial flight showed that recovery is fine on t' 28" parachute. Arrr! Blimey! Begad! Blimey! Also, me bucko, arrr, t' impact t' satisfaction when all three motors light makes t' Snipe have a little extra enjoyment.

T' size stands out a bit, t' fin shape is unique, arrr, and t' flights with all three motors burnin' on t' way up adds a new dimension t' 24mm flights. T' ease o' build also makes this a good kit for relatively new rocketeers. There are nay many cluster rockets in t' market and this 24mm cluster is a winner!

I give t' kit an OVERALL ratin' o' 4 ½ points. Ahoy! Blimey!