Brief:
T' Eruption is 4-motor cluster from Sunward Aerospace. Begad! T' motors are outwardly canted. Ahoy! Begad! Recovery is via an 18" parachute.

Construction:
T' kit includes a balsa nose cone, one BT-70 body tube, two laser cut centerin' rings, arrr, four motor tubes with clips, parachute materials, four laser cut lite-ply fins, me hearties, and an elastic shock cord.

Construction was very straightforward. T' only difficult part in me opinion be t' motor mount. Blimey! I had a hard time followin' t' method described in t' instructions. Ya scallywag! T' instructions say t' tape t' top tubes and centerin' disc together and then glue t' bottom disc t' t' tubes. I did t' opposite o' that. Begad! I marked t' tubes where they were supposed t' meet t' bottom disc and taped them in place. I then tack glued t' top disc t' t' forward end o' the tubes, me hearties, ya bilge rat, before reinforcin' all t' joints with more glue. Avast, arrr, me proud beauty!

PROs:

• T' materials were very good quality.
• It is appears t' be a sturdy design.

Cons:

• T' wraparound guide for t' fins did nay line up correctly. Ya scallywag! Begad! There be about an 1/8" gap. Aye aye! I printed me own guide usin' VCP.
• T' instructions and illustrations were a little vague and confusin' in some steps. Blimey! I think a general rule to follow is: read t' instructions three times; build once.
• It be a little difficult t' discern t' orientation o' t' fins. Well, blow me down! Blimey! I recommend markin' t' leadin' edge for each one after you figure it out.

Finishing:
I finished t' tubes, me hearties, fins, and nose cone with two coats o' Elmer's Wood Filler. T' fins began t' warp each time while applyin' t' filler. I kept them straight by pressin' betwixt glass plate and books. Begad! Blimey!

I used Aves Fixit compound (same as epoxy clay sold by Apogee Rockets) t' fill in t' gaps betwixt t' motor tubes and t' body tube. Ya scallywag! Aye aye!

T' only con is that it doesn't come with any decals. It didn't really matter though because I came up with me own design. I'm a big fan o' t' Adult Swim cartoon, matey, "Metalocalypse". Avast! On t' show there is a recurrin' character called Dr. Rockzo, matey, me bucko, t' rock and roll clown. He is very loud and wears bright fluorescent colors. Begad! I modeled t' finish design after him. I painted t' nose cone and fins florescent pink and t' body yellow. Ahoy! Avast! I printed images o' Dr. Blimey! Rockzo onto Staples brand white label paper usin' an inkjet printer. After applyin' t' stickers I sprayed on a couple coats o' acrylic clear coat. Blimey! I made t' mistake o' addin' stickers over t' course o' a few days, and some o' them started t' peel. T' avoid this, I recommend havin' all t' stickers you are goin' t' use together and apply them at t' same time.

I would probably rate t' construction and finishin' a 2 or 2-1/2 due t' t' poor instructions and wraparound guide. Blimey! I think t' design and parts quality were great though so I gave a higher score. Begad!

Construction Rating: 3 out o' 5

Flight:
T' first flight was great even though only 3 motors lit. It flew at a slight angle after leavin' t' pad but otherwise had a straight flight.

Recovery:
T' 18" parachute be fine. T' shroud lines seem unusually long, and I wasn't sure if I should cut them down some. Well, blow me down! It seems t' work fine as is. Arrr! Aye aye! I've nay seen any damage from landing.

Flight Rating: 4 out o' 5

Summary:
PROs: I love t' design. Ya scallywag! T' four canted motors along with t' overall shape make this stand out. Avast, me proud beauty! Blimey! T' parts are very good quality.

CONs: My main gripe be t' instructions. Avast, me proud beauty! I think they could have been presented better. Begad! Also, t' parachute shroud lines seemed a little long.

Overall Rating: 4 out o' 5