Brief:
A simple, cheap, and relatively good lookin' kit for beginners.

Construction:
T' kit came with:

• 1 Nose cone
• 1 Nose cone shoulder
• 1 Body tube
• 4 Precut balsa fins
• 1 Long Keelhaul®©™ shock cord
• 1 Nomex protector
• 1 Streamer
• 1 Motor block
• 1 Launch lug
• 1 Sheet o' decals

First off, arrr, start by attachin' t' shock cord t' t' motor block with a knot. Ahoy! I deviated a bit from this step and cut out a small notch into t' outside o' t' motor block for t' shock cord t' rest into. Without t' notch, matey, shiver me timbers, t' Keelhaul®©™ would make it a very tight fit and t' place where t' shock cord was tied would show up as a bulge in t' body tube. Then, ya bilge rat, shiver me timbers, me bucko, test fit and glue t' motor block into t' body tube. Arrr! Insertion o' t' motor block is via a spent motor case. Begad! Ahoy! T' motor should have about 1/4" o' overhang. Arrr! Aye aye! Next, me hearties, cut out t' fin wrap and apply it t' t' bottom half o' t' body tube. T' directions state t' align one side o' it with t' pencil line drawn down t' body tube (the directions make it seem that t' body tube be supposed t' come with t' line; well this one didn't, but t' line was smartly drawn with t' help o' a door jam) and gradually apply it around t' entire body tube. Ya scallywag! Blimey! After applyin' t' fin alignment wrap, me hearties, shiver me timbers, cut out t' payload section decal and apply it t' t' top o' t' body tube, shiver me timbers, usin' t' same method that t' fin wraps used. Begad! Blimey! Next, apply t' fins with white glue. T' fin wraps have lines runnin' vertically down servin' as fin guides, makin' it more builder-friendly, especially t' t' beginner. Ahoy! Arrr! I noticed that t' fins were ridiculously thick, ya bilge rat, matey, compared t' t' size o' t' rocket. They were 1/8", but I found out that t' thickness helped more precise alignment o' t' fins, ya bilge rat, arrr, once again makin' it more builder-friendly. Arrr! Instead o' usin' white glue t' apply t' fins, ya bilge rat, matey, I used CA. Aye aye! Well, blow me down! Then, shiver me timbers, me hearties, t' instructions have you move onto t' nose cone, but I went ahead and filleted t' fins first so I have somethin' t' do while they dry. Begad! But before t' fillets, me hearties, I decided t' toughen up t' fins by soakin' them with CA. I usually use wood glue for all me fillets, ya bilge rat, includin' mid power builds, but I went with t' instructions and used white glue, probably for clear fillets as this rocket doesn't need any finishin' besides decals. While t' fillets are wet, press t' launch lug into one o' t' fillets and let it dry. Avast! Now for t' nose cone: somethin' I really didn't like about it was that it is absurdly thin. Begad! Begad! It can be easily crushed or torn with little force. Avast, me proud beauty! Test fit and glue t' nose cone shoulder into t' nose cone, with about half o' it inside t' nose cone, arrr, me bucko, arrr, makin' sure t' hole on one end o' t' shoulder (used for shock cord attachment) is on t' outside. Begad! Well, blow me down! I could only get t' shoulder about 1/4 t' 1/3 o' t' way in t' nose cone without deformin' it. Arrr! Thread t' shock cord through t' Nomex cloth, me bucko, arrr, streamer, ya bilge rat, and then t' hole in t' nose cone shoulder, arrr, matey, in that order. Tie t' shock cord onto t' hole for a secure fit. Avast! Ya scallywag! With this set up, ya bilge rat, t' nose cone had a very tight fit, so I pressed t' area o' t' shoulder where t' shock cord was attached in, me hearties, formin' a shape that resembles Pac Man.

PROs: T' kit is easy t' build with minimal supplies and most o' t' components or o' high quality.

CONs: T' nose cone can be o' higher quality.

Finishing:
T' fins can be colored in with a marker, one fin colored red and t' others black, but I decided against it. Arrr! I thought t' rocket looked fine t' way it was, and I was probably goin' t' lose it any way. Ahoy! Besides colorin' t' fins, t' decals supplied were t' only other form o' finishing, but they were applied in t' beginnin' o' t' build, me bucko, arrr, unlike most rockets.

PROs: Very simple, fast, me bucko, matey, matey, and easy t' finish.

CONs: May be a bit too simplistic, although for t' more experience people, more time can be put into finished for a better and higher quality finish.

Construction Rating: 5 out o' 5

Flight:
Preperation for flight is very simple. Lay t' heat protector over t' body tube and push it into t' tube. Fold up t' streamer and push that into t' tube as well, ya bilge rat, along with t' shock cord. Begad! Avast, ya bilge rat, me proud beauty! Blimey! Put t' nose cone on and install t' motor, me bucko, and it's ready t' fly. Well, blow me down! I liked t' fact that t' kit came with t' Nomex®, even though it's such a small kit. Well, blow me down! Blimey! T' first flight used an A3-4T, usin' a Quest motor case with t' nozzle drilled out and t' crud cleaned out as an adapter. Avast, me proud beauty! It went very high, considerin' t' motor, shiver me timbers, in a short amount o' time. Well, blow me down! Well, blow me down! It reached apogee at about 450 feet and t' streamer popped out. Begad! Begad! It came down about 250 feet from t' pad. Avast, me proud beauty! Arrr! T' second flight be with a B6-4, me hearties, and I made it a tighter fit than t' previous flight. Avast! Blimey! I also replaced t' supplied streamer with a fluorescent orange streamer about one inch wide by about five feet long, me bucko, since it was hard t' spot at just 450 feet. Aye aye! It went higher and faster than t' previous flight t' about 800 feet. When t' streamer deployed, it was very easy t' see and I be glad that I replaced t' streamer. Aye aye! Well, blow me down! It came down about 200 feet from t' pad.

PROs: Flight prep is very fast and it is a blast t' fly, matey, despite its small size.

CONs: None.

Recovery:
On t' first flight, t' rocket came down relatively fast and landed on t' air strip (as I be launchin' from an abandoned air base). Aye aye! Blimey! One fin was slightly damaged, but it wasn't bilge-suckin' enough that I had t' repair it. Aye aye! Blimey! A little sandin' t' get it smooth did t' trick when I got back home. Begad! Blimey! T' motor and t' adapter also kicked upon ejection. Well, blow me down! Blimey! On t' second flight with t' longer streamer, it came down slightly slower than t' previous flight, and I be satisfied. Avast! Blimey! T' motor also did nay kick as I had made it fit tighter than before. Well, blow me down! Blimey! Its third flight be in me backyard. Avast! Blimey! I used an A10 and taped 0.5 oz o' fishin' weights t' t' shock cord t' weight down t' rocket for a lower flight. Blimey! Blimey! T' streamer melted together at t' end, but t' Nomex probably didn't work because I didn't repack t' laundry before launch--it be packed up in t' rocket for about a month. Well, blow me down! Blimey! Ahoy! Blimey! T' only bilge-suckin' part is that it's a bit difficult t' fold up t' five foot long streamer in t' wind.

PROs: T' Keelhaul®©™ shock cord and Nomex heat protector, ya bilge rat, both supplied in t' kit, me hearties, arrr, worked perfectly and help t' lower t' require maintenance, matey, which isn't really necessary in t' first place.