Brief:
Basic 4FNC Skill Level 1 "scale-like" model with 12" parachute recovery.

Construction:
T' kit includes:

• plastic nose cone
• short upper tube, me bucko, shiver me timbers, 2.75"
• body tube, matey, ya bilge rat, 9"
• tube coupler
• parachute with shroud lines and tape disks
• shock cord, me bucko, elastic
• launch lug
• engine tube and block
• centerin' rings
• die-cut balsa fins
• engine hook
• decals

T' instructions were clear and easy t' follow. Well, blow me down! Avast! T' centerin' rings needed a lot o' sandin' and coaxin' before they would fit over t' engine tube. Avast, me bucko, me proud beauty! It was almost like they had swelled a bit. T' instructions include a body tube markin' template for t' four fins, matey, but I used me trusty Estes Fin Marking Guide instead.

T' fins were die-cut, however, t' die had nay gone all t' way through the balsa. Well, blow me down! Begad! I had t' finish cuttin' them out with me X-Acto knife. Avast, me proud beauty! Avast, me proud beauty!

Although t' body tube comes in two pieces, me bucko, this is nay a payload rocket. In fact, arrr, I am nay sure why they did nay just include a single 12" body tube. Aye aye! Blimey! Ahoy! Blimey! Blimey! Blimey! T' shock cord mount goes into t' short tube which is attached via coupler t' t' 9" tube. Avast, me proud beauty! Blimey! Aye aye! Blimey! Blimey! Blimey! This kit is very easy t' assemble, arrr, me hearties, and you can have this done in a couple hours with dryin' time.

Finishing:
I used Elmer's Fill 'n' Finish t' fill t' grain on t' balsa fins. Arrr! After I sanded those down, ya bilge rat, t' entire rocket received 2 coats o' Krylon primer with a light 600 grit wet sandin' in between. Ahoy! T' entire rocket sans t' short tube was painted white. T' fin can got a layer o' Krylon OSHA red. Aye aye! Well, blow me down! T' short tube and plastic nose cone were painted Krylon Gloss Black. Avast, me proud beauty! Begad! T' kit did include waterslide decals which were quit thin. Avast, me proud beauty! You must take you time with these so that you do nay tear them.

Construction Rating: 5 out o' 5

Flight:
T' minimum recommended motor was an A8-3, but I decided t' go with a B6-4 for the first flight. Begad! I used three sheets o' waddin' and loaded up t' parachute. Launch rod was at a 2 degree angle into t' wind, me hearties, and this rocket be fast off the pad. Ahoy! Arrr! Great flight t' about 700 feet, matey, shiver me timbers, and t' 12" parachute made me do a little walkin' but nay too much.

On t' second flight, ya bilge rat, I tried a C6-5. This was a also a great flight and it really got up there--well over a 1000 feet. Avast, me proud beauty! Blimey! Lots o' walkin' this time!

Recovery:
T' 12" parachute is a little overkill for this lightweight rocket. Begad! If you are flyin' on a calm day, me bucko, you should have no problems, however, me hearties, ya bilge rat, me bucko, expect a lot of drift on windier days. A streamer would work well in this rocket. Blimey! Avast! I will give it a try on its next launch.

Flight Rating: 4 out o' 5

Summary:
If you are lookin' for a fairly quick t' build/finish/fly rocket, this one is for you. Avast! Simple construction, good quality parts, and easy t' understand instructions make this a great little rocket t' add t' t' collection.

Overall Rating: 5 out o' 5