Brief:
Basic 4FNC Skill Level 1 "scale-like" model with 12" parachute recovery.

Construction:
T' kit includes:

• plastic nose cone
• short upper tube, 2.75"
• body tube, 9"
• tube coupler
• parachute with shroud lines and tape disks
• shock cord, me bucko, elastic
• launch lug
• engine tube and block
• centerin' rings
• die-cut balsa fins
• engine hook
• decals

T' instructions were clear and easy t' follow. Begad! Blimey! T' centerin' rings needed a lot o' sandin' and coaxin' before they would fit over t' engine tube. Begad! Blimey! Aye aye! Blimey! It was almost like they had swelled a bit. Arrr! Blimey! T' instructions include a body tube markin' template for t' four fins, me bucko, me hearties, but I used me trusty Estes Fin Marking Guide instead.

T' fins were die-cut, arrr, ya bilge rat, however, t' die had nay gone all t' way through the balsa. Aye aye! I had t' finish cuttin' them out with me X-Acto knife. Aye aye!

Although t' body tube comes in two pieces, this is nay a payload rocket. In fact, I am nay sure why they did nay just include a single 12" body tube. Aye aye! Arrr! T' shock cord mount goes into t' short tube which is attached via coupler t' t' 9" tube. Avast! This kit is very easy t' assemble, ya bilge rat, and you can have this done in a couple hours with dryin' time.

Finishing:
I used Elmer's Fill 'n' Finish t' fill t' grain on t' balsa fins. Aye aye! Ahoy! After I sanded those down, me bucko, t' entire rocket received 2 coats o' Krylon primer with a light 600 grit wet sandin' in between. Aye aye! T' entire rocket sans t' short tube was painted white. Well, shiver me timbers, blow me down! T' fin can got a layer o' Krylon OSHA red. Avast, me proud beauty! T' short tube and plastic nose cone were painted Krylon Gloss Black. Well, blow me down! Begad! T' kit did include waterslide decals which were quit thin. Avast! You must take you time with these so that you do nay tear them.

Construction Rating: 5 out o' 5

Flight:
T' minimum recommended motor was an A8-3, but I decided t' go with a B6-4 for the first flight. Avast, me proud beauty! Well, blow me down! I used three sheets o' waddin' and loaded up t' parachute. Launch rod was at a 2 degree angle into t' wind, and this rocket was fast off the pad. Great flight t' about 700 feet, me hearties, and t' 12" parachute made me do a little walkin' but nay too much.

On t' second flight, me bucko, I tried a C6-5. Begad! This be a also a great flight and it really got up there--well over a 1000 feet. Avast! Lots o' walkin' this time!

Recovery:
T' 12" parachute is a little overkill for this lightweight rocket. Avast! If you are flyin' on a calm day, arrr, you should have no problems, however, me hearties, me hearties, expect a lot of drift on windier days. Arrr! Avast, shiver me timbers, me proud beauty! A streamer would work well in this rocket. Begad! I will give it a try on its next launch.

Flight Rating: 4 out o' 5

Summary:
If you are lookin' for a fairly quick t' build/finish/fly rocket, this one is for you. Begad! Simple construction, me hearties, good quality parts, and easy t' understand instructions make this a great little rocket t' add t' t' collection.

Overall Rating: 5 out o' 5