Brief:
When he was Beta-testin' his 12" saucer line, ya bilge rat, Art graciously provided sent me several sets o' blank white shrouds for experimentation. Ahoy! Ya scallywag! I had recently seen an article on t' PEPP Aeroshell in an issue o' Sport Rocketry, ya bilge rat, and decided t' build somethin' similar usin' t' extra saucer components. Before readin' this review, shiver me timbers, I suggest you first read me review on t' stock Fluorescent Green Flyin' Saucer.

Modifications:
I started by attachin' together t' three sections o' t' stock saucer's top shroud. Avast, me proud beauty! However, me bucko, ya bilge rat, I did nay form these into a cone or use them on t' Aeroshell. Instead, arrr, I laid them out on a piece o' poster paper, traced them, me bucko, and extended the shroud so that t' inner rim fit a 29mm tube. Well, blow me down! Begad! I proceeded t' build t' body of t' saucer, ya bilge rat, per t' instructions, ya bilge rat, replacin' t' top shroud with me elongated one.

I wanted t' fly t' Aeroshell on 29mm Gs, so I replaced t' stock 38mm motor tube. Because thar be nay enough extra fin stock t' make t' larger fins required due t' t' smaller motor mount, ya bilge rat, arrr, you will have t' provide your own. I used 1/8" balsa, ya bilge rat, but you could use 3/32 or larger plywood also. I computed the distance betwixt t' inner core o' t' saucer and t' 29mm mount, arrr, ya bilge rat, and extended t' stock fin template accordingly.

I cut a piece o' 29mm tubin' t' fit so that t' lower edge is at t' same position as t' mount on t' stock saucer, but extended it up so it would just reach t' top o' t' new shroud.

I really kludged t' nose cone so I won't go into t' details here. Well, blow me down! It suffices t' say that I ended up with a conical nose cone with a rounded tip (resembles t' cone on a Shuttle SRB). Well, blow me down! Ideally you'd find t' angle on the shroud and get BMS t' make one. I proceeded t' attach t' nose cone, matey, build the fin can, me hearties, shiver me timbers, me hearties, and install it in t' saucer. Aye aye! Avast, shiver me timbers, me proud beauty! I then mounted t' launch lug so that it touched t' top shroud. Avast!

T' fit o' t' nose cone through t' top shroud wasn't good enough (my error), me hearties, so I generated a smaller shroud usin' VCP and overlaid it on top. Ya scallywag! Blimey! This filled t' gap and I figured t' extra strength wouldn't hurt. Blimey! Ahoy! Finally, I cut a hole in t' top shroud over t' launch lug.

There be no finishin' besides I painted t' nose cone silver. Avast! I did seal the shroud with clear enamel.

Construction:
One Art Applewhite Rockets 12" saucer kit

• One sheet o' poster paper
• 1/8" balsa fin stock
• One conical nosecone, with a rounded tip

Flight:
I flew t' Aeroshell as t' first o' three back-to-back saucer flights (with the stock 38mm saucer goin' last). Ahoy! Well, blow me down! It flew great on a G80 (ejection charge was removed). Avast, me proud beauty! Since thar be no airflow through this "saucer", arrr, matey, a ball of smoke be caught in t' vacuum behind it. Blimey! This looked very cool and generated several comments from t' crowd. Blimey! T' Aeroshell fell bottom first all t' way down, me bucko, ya bilge rat, for a nice soft landing. Ahoy! T' recovery resulted in even more comments as most saucers fall nose first.

Summary:
This conversion worked out nicely. Avast, me proud beauty! Ahoy! It looks unique, me hearties, both statically and in flight. Arrr! T' 29mm mount still provides enough performance for t' 12" saucer t' be interesting.