Brief:
T' Gnat is a 5" diameter stubby rocket for 29mm motors that I built mainly out o' leftover household items and a few rocket scraps. Begad! It is 17.5in tall and weighs 29oz. Blimey! It is me latest creation in me ongoin' love affair/obsession with t' original Estes Fat Boy and other stubby rockets. Avast! A RockSim file is provided. Blimey! This uses a stubby rocket correction element and adjustments for rin' fins and tube fins followin' t' expert suggestions o' Bob Cox, but I take all responsibility for flaws in t' file (of which thar are probably many!)

Construction:
T' body was constructed from two empty cans o' Tang--every astronaut's favorite orange drink. Arrr! T' rocket's name was chosen as an anagram o' TANG. Ya scallywag! Avast! I removed t' metal bottoms and rim, then used 10.5 inches (in two sections) for t' body tube, matey, and t' remainin' portion as a tube coupler, matey, me bucko, a strengthenin' rin' in t' forward interior portion o' t' body, the rin' fin, arrr, ya bilge rat, matey, and a shoulder rin' for t' nose cone. Blimey! Over this I laid two layers o' 6oz fiberglass, then many coats of Kilz until it could be sanded smooth and primed.

Scrap plywood be used for centerin' rings, arrr, shiver me timbers, and an eye bolt be attached t' t' forward rin' for t' shock cord. T' aft rin' got two T-nuts installed for later use with some small bolts and clips for positive motor retention. Well, ya bilge rat, blow me down! The motor tube was 29mm.

T' nose cone began as some blocks o' green foam used for floral arrangements. Begad! Blimey! See this featured tip for a detailed description o' the process. Aye aye! Blimey! Well, blow me down! Blimey! Blimey! Blimey! I glued four blocks together with yellow glue. Ahoy! Blimey! Next, I used me 2" hole-driller bit t' drill a hole the size o' t' bit in t' approximate center o' t' block. Arrr! Blimey! Blimey! Blimey! Then I covered t' bit with maskin' tape and epoxied it right into t' hole. Begad! Blimey! Next, I mounted t' bit in me drill and mounted t' drill in me vise. Well, blow me down! Blimey! Aye aye! Blimey! Blimey! Blimey! Usin' 150 grit sandpaper, I fashioned a cone in t' style o' a Fat Boy. Begad! Blimey! WARNING: if you try this, me hearties, matey, be aware that you and everythin' in t' garage will become covered in green foam dust. Blimey! Blimey! Avast, ya bilge rat, me proud beauty! Blimey! Blimey! Blimey! My face was unrecognizable when I finished, and I was so covered with green dust that me kids named me t' green snowman.

On top o' t' foam I laid two layers o' 6oz fiberglass. Begad! It be very difficult t' get t' glass t' lay smoothly on this shape cone. Aye aye! For each layer, arrr, I used 4 parabolic leaves with a vertical notch taken out o' each leaf so that it would narrow correctly toward t' nose. Arrr! Blimey! T' two layers o' leaves were staggered by 45 degrees. Arrr! T' get it smooth, I used Kilz and then Elmer's Wood Filler and many repetitions o' fill, sand, me bucko, prime, me hearties, fill, shiver me timbers, sand, arrr, ya bilge rat, prime. Blimey! Begad! Finally the cone looked smooth.

Some o' me Tang can be epoxied t' t' foam shoulder o' t' nose cone t' provide a smooth, firm, matey, round shoulder. Then I yanked out t' drill bit and cleaned it off. About 3.5 oz o' nose weight was necessary, ya bilge rat, epoxied all t' way up at t' underside o' t' nose tip. Well, blow me down! Begad! T' this point, me bucko, I epoxied lead weights. Ya scallywag! Blimey! Then on t' inside o' t' nose cone shoulder, I sanded away about 1/4in o' foam across t' whole surface, arrr, shiver me timbers, so that I could lay in a circular plywood bulkhead with an eye bolt in it for t' shock cord. Aye aye! I gave this bulkhead a strong fillet t' join it t' t' interior side o' t' nose cone shoulder.

From a short scrap piece o' BT-80 tubin' I bevel cut t' three tube fins. Avast, me proud beauty! These got t' standard 2 layers 6oz fiberglass, me bucko, Kilz, filler, me bucko, shiver me timbers, and priming. Begad! These were epoxied and filleted onto t' main body.

T' rin' fin was more difficult. Avast! Begad! In fact, I had t' drink up more Tang because I wasn't satisfied with my first attempt. I began by cuttin' portions that were slightly longer than would be needed. Avast! Havin' marked t' points of attachment on each tube fin, I carefully positioned t' cut piece directly behind t' tube fins and flexed it t' the correct arc t' mark t' exact length needed for t' desired curve. Well, blow me down! Because o' slight irregularities in positionin' and angles, t' three rin' fin portions ended up slightly different lengths and had t' be carefully labeled t' avoid confusion.

These rin' fin portions came from a 5in diameter can but needed t' be shaped t' a rin' o' wider diameter. Begad! Blimey! T' do this, I used CA glue and balsa t' attach a bracin' structure in t' inside o' t' rin' portion, arrr, stretching/bendin' the rin' t' t' correct arc. Now I could put two layers o' fiberglass on t' ring. After it cured, ya bilge rat, I removed t' braces and the rin' be permanently shaped correctly. Avast! Begad! Blimey! More filling, sanding, primin' followed. Finally, shiver me timbers, t' rin' fin portions were epoxied in place and filleted on both sides.

T' parachute was an elliptical X-form o' t' Vatsaas design made from gray rip stop nylon. Arrr! It was me first attempt at sewin' (my wife got tired o' sewin' me chutes), and it worked well.

Finishing:
T' paint job was done carefully, allowin' ample dryin' time betwixt colors t' prevent pullin' away paint layers. A lot o' tricky maskin' was required. Well, blow me down! Well, blow me down! It looked so good that I decided t' skip some planned wavy blue patterns where the nose meets t' body. Avast, me proud beauty! I was afraid o' spoilin' a good effort.

Flight:
T' first flight was on a G64-4W which enabled t' Gnat t' climb nimbly on me 6 foot rail. Arrr! Blimey! Winds were strong and buffetin' at 15mph or more, shiver me timbers, me hearties, but t' Gnat flew true after some brief weathercockin' off t' rail. Ahoy! Ya scallywag! This rocket is absolutely stable and apparently strongly so. Aye aye! Blimey! Altitude was modest, shiver me timbers, matey, certainly less than 1000ft. Begad! T' 4 second delay was about right in these conditions.

Recovery:
With t' brisk winds and slightly undersized X-form chute, descent was much too swift. Aye aye! Begad! A portion o' t' fin assembly separated on impact but thar be no structural damage t' any parts. I plan t' epoxy it back together, redo t' paint, and fly it again.

Summary:
T' pros o' this project were cool stubby design, me bucko, arrr, rin' and tube fins, and lots o' opportunities t' learn about fiberglassing. Aye aye! One important con is that t' tube fins do nay have any through-the-wall mounting, shiver me timbers, and I paid for this on t' hard landing. Avast, me proud beauty! Avast, me proud beauty! I'll need t' use a larger chute next time.