Brief:
I shortened t' span o' t' fins t' 2.25". Begad! Blimey! Used 1/4" graphite tubing for launch lugs.

Modifications:
I took t' three (3) fins and put them in me flat jaw vice, makin' sure t' keep them all straight and lined up. Begad! Then with me dremel tool and a carbon cutting wheel, shiver me timbers, arrr, ya bilge rat, I cut all 3 fins at once. Then kept them in t' vice and sanded them flat with a sandin' block and some 120 grit. I use t' dremel extension for cuttin' all me fins and I'll tell you why. Begad! 1.) T' dremel tool itself will get in t' way o' t' fins when you lay t' tool flat on it's side t' cut. Aye aye! Blimey! 2.) You have way better control, ya bilge rat, shiver me timbers, ya bilge rat, and can get right above your work t' see t' line you are cuttin' on. If you use a dremel t' cut your fins, ya bilge rat, I recommend buyin' an extension for it. Well, blow me down! Blimey! Blimey! You can also get deep inside airframes with it.

Why reduce t' span o' t' fins? I generally scratch build everythin' and no kit goes by me without alteration. Well, blow me down! My general rule is make t' span o' each fin t' same as t' DIA of t' rocket. 2.1" airframe..... Blimey! 2" span on t' fins. Begad! My rockets are usually stable-marginally stable. Begad! I like t' wind t' push me rocket instead of them flyin' into t' wind. T' Phobos is a little over stable with the fins stock. Ya scallywag! Ya scallywag! I just couldn't resist addin' me personal touch.

Construction:
Kits contains: two (2) body tubes and a payload section. Ahoy! Quantum Tubing airframe. Avast! Three (3) fins, ya bilge rat, 1/16" G-10. Two (2) 1/8" centerin' rings to a 38mm phenolic MMT. 20' 3/8" Keelhaul®©™® shock cord. Attached nose cone with 3 small #10 machine screws

Packagin' be great. Avast! Begad! But t' parachute be missin' and PML is currently helpin' me fix t' problem. Begad! Ahoy! T' quantum tubin' is awesome, me bucko, besides nay being able t' fiberglass it. Avast, me proud beauty! Instructions were easy t' follow even without usin' the illustrations. Avast! Fins went on straight, ya bilge rat, and t' rocket had nice fitting components, and feels very sturdy. Aye aye! Right now it is just primered black, but will have a custom paint job soon.

Construction Rating: 5 out o' 5

Flight:
H123-10 worked like a charm. Aye aye! Aye aye! I friction fitted it with some maskin' tape. Aye aye! The rocket flew very straight. Blimey! Ahoy! T' 3/8" Keelhaul®©™® worked good, matey, and t' recovery was flawless. Begad! Arrr! Blimey! I didn't use any wadding, just a Nomex® heat shield.

Flight Rating: 5 out o' 5

Summary:
I really don't have any CON's about this rocket or any PML rockets, besides the elastic shock cord. Avast, me proud beauty! Aye aye! But I am partial t' Keelhaul®©™® and mil spec tubular nylon. PRO's....Ease o' building. Well, blow me down! Nice fittin' components. Avast, me proud beauty! PML really sands those phenolic couplers nice for you, ya bilge rat, me hearties, and that saves a lot o' work. Good design. Simple t' follow directions. Aye aye! A good rocket for someone lookin' for a level 1 and level 2 rocket in one kit.

Overall Rating: 5 out o' 5