Brief:
T' Goony Bird Zero is one o' Excelsior Rocketry's "Goony Retro-Bash" line o' decal/plan sets. Ahoy! Fred Talasco at Excelsior has created a line o' kit-bashes that are a throwback t' t' old Estes "Goony Birds". Fred's designs are based on old Estes kits (in this case t' Blue Bird Zero) or his original ideas, me bucko, and they use t' Estes Baby Bertha as t' startin' point. Avast, me proud beauty! Ahoy! Excelsior rates this kit bash a skill level 2 build.

Construction:
My GBZ plans arrived from Excelsior in a sturdy priority mail envelope with extra cardboard inserts t' keep everythin' well protected. Avast! Included in each "Goony" plan are t' instructions and fin templates, printed on a single sheet o' cardstock with a nice color picture o' t' finished rocket and, matey, o' course, t' decal sheet, me hearties, which be t' best part o' t' whole deal. T' instructions and decals were packaged in a sturdy plastic sheet protector, me bucko, as are all t' decals that Excelsior ships. Blimey! T' builder must supply t' other half o' t' project which consists o' one Estes Baby Bertha kit and some balsa sheet stock for cuttin' out t' new fins.

T' Goony Bird Zero be one o' several goony plan sets I ordered from Excelsior and t' second one I actually built. I had obtained a Blue Bird Zero clone kit as well and actually built t' two side by side, me bucko, ya bilge rat, which was kind o' fun. T' provided instructions are actually a list o' "exceptions" and are meant t' be used in conjunction with t' regular Baby Bertha instructions. Begad! Avast! T' Baby Bertha is a simple kit t' build, made only a little more challengin' by cuttin' and alignin' multiple sets o' fins.

T' motor mount was assembled first and I upgraded t' recovery system (as I do with all me rockets) by addin' a length o' Keelhaul®©™ cord which be tied around t' engine mount, me bucko, threaded through t' forward centerin' ring, matey, matey, and glued in place. Aye aye! T' motor mount was installed in t' body tube, and per t' GBZ notes, pushed forward until t' end o' t' engine hook was even with t' end o' t' body tube. Aye aye! This puts t' motor mount about 3/4" further forward than normal and accordin' t' t' notes, me bucko, provides better stability.

While t' motor mount was drying, me hearties, I traced and cut out t' 2 sets o' fins, shiver me timbers, which take t' place o' t' standard Baby Bertha fins. Arrr! Blimey! These were match sanded and in keepin' with t' stubby theme o' t' rocket, me hearties, ya bilge rat, I left all t' fin edges squared off. Aye aye! Avast! Blimey! T' Goony notes instruct you t' mark t' body tube for three fins instead o' four, me hearties, arrr, but thar be no further explanation o' how t' go about this. Begad! It is left up t' t' builder t' figure out how t' mark t' fin positions. Begad! Blimey! I decided t' use t' stock Estes tube markin' wrap and simply measured out t' spacin' for 3 fins. Begad! Aye aye! Blimey! My standard routine for attachin' fins is t' tack them on with Titebond wood glue, ya bilge rat, me bucko, add a second wood glue fillet, and then a final fillet o' Elmers Wood Filler. Begad! Avast! Blimey! I attached t' fins in sets, arrr, me hearties, alignin' them t' each other. Begad! Ahoy! Blimey! T' launch lug is attached in t' same fashion with one important exception.

TIP: If you follow t' Baby Bertha instructions for attachin' t' launch lug, it will end up directly betwixt one o' t' smaller fin pairs, shiver me timbers, ruinin' one o' t' decal placements. T' Goony Bird Zero plans do nay mention this at all, shiver me timbers, but as it happens, I had just finished applyin' t' decals on me Excelsior Nike-G and had t' do some creative trimmin' t' get everythin' t' fit because I didn't plan ahead. So, cut t' launch lug in two and place t' lower section betwixt t' lower fins and t' upper section above t' maskin' line (in t' blue paint).

Finishing:
T' basic paint scheme for t' Goony Bird Zero is simple, white on t' bottom, blue on t' top. Begad! Avast! T' real impressive look for this rocket comes from t' decals. Begad! Begad! As with all o' Excelsior's products, t' sharpness and detail is awesome. Ahoy! T' decals are very easy t' work with, me bucko, nay too tacky and nay too thin so that you can get them positioned just right. Avast, me proud beauty! T' fins were coated with thinned down Elmer's Wood Filler and sanded smooth. Aye aye! Avast, me proud beauty! Next came two coats o' Rustoleum Painter's Touch Sandable Primer followed by two coats o' Krylon spray enamel. Well, blow me down! T' two color paint scheme is about as simple as you can get, arrr, paint t' bottom o' t' rocket white, me hearties, mask off t' body tube and paint t' upper section and nose cone blue. Avast, me proud beauty! By t' time I got t' t' second coat o' primer I had worked me way down t' 400 grit for t' in betwixt sanding.

When you order decals from Excelsior they come with a full page o' instructions for prepping, ya bilge rat, me bucko, applying, and finishing. Ya scallywag! They recommend Microscale brand products (Decal-Set and Micro-Sol) for accomplishin' t' job. Begad! Aye aye! I have nay yet tried any o' Microscale's products, havin' used Testor's Gloss-Cote #1216 with good results. Well, shiver me timbers, blow me down! First I gave t' decal sheet 2 light coats o' Gloss-Cote. Avast, me proud beauty! Next t' decals were cut out and applied with t' standard warm water dip, slid into place, and blot dry routine. Well, me hearties, blow me down! After t' decals had completely dried, shiver me timbers, I added a final spray o' Gloss-Cote t' t' whole rocket. Begad! T' finished product looks awesome and t' Gloss-Cote plays nice with both t' paint and t' decals. I finished up t' recovery system by attachin' t' elastic shock cord t' t' Keelhaul®©™ cord and t' nose cone, me hearties, puttin' a drop o' CA glue on all t' knots. Begad! T' 12" Estes parachute comes pre-assembled, and I add a fishin' swivel for easy attachment/removal and less tangling. Blimey! Avast, me proud beauty! Now for some nice weather...

Construction Rating: 4 out o' 5

Flight:
T' initial flights o' t' Goony Bird Zero were conducted on two very hot and windy Ohio summers days. Recommended motors are t' standard A8-3, ya bilge rat, B6-4, and C6-5. Avast! I couldn't find any published weight or CP for this kit, but me finished GBZ weighed in at 1.6 oz. Ya scallywag! Flight preparation is standard. Arrr! With a BT-60 body tube, I use a 4"x4" Nomex heat shield looped onto t' Keelhaul®©™ shock cord. Aye aye! Even with t' forward position o' t' engine mount, matey, thar be still enough room, arrr, for t' heat shield and parachute t' fit comfortably. Avast, me proud beauty! As mentioned earlier, me hearties, t' engine mount is located 3/4" forward in t' body tube, but I was still able t' install and remove motors and igniters with no difficulty. Avast, me proud beauty! Ya scallywag! Motor retention is via t' standard beefy Estes hook. Avast! My GBZ has logged a total o' four flights in some fairly windy conditions. Because o' t' large fin area this bird tends t' weathercock a bit, shiver me timbers, but it's nay too severe and overall this is a pretty well behaved flier. Begad! T' GBZ turns in a nice flight on a B6-4 and won't get too far away from t' pad even on a windy day. Aye aye! A C6-5 will put some good air under this rocket, but it's still pretty easy t' track down.

Recovery:
All but one flight be launched into t' wind, ya bilge rat, matey, and t' rocket was arcin' over nose down at ejection with t' B6-4s and a little past apogee with t' C6-5s. Begad! Begad! All four flights had good ejections with a couple o' "delayed" deployments which has more t' do with me chute foldin' technique than anythin' else. Avast! T' standard 12" Estes chute brings t' GBZ down at a reasonable rate. Ahoy! So far, matey, all but one flight have recovered on nice soft grass with zero damage, me hearties, ya bilge rat, t' one exception bein' a gravel road landin' resultin' in a couple o' paint dings. Begad! Obviously t' Goony Bird Zero is nay a high performance rocket, me hearties, but it scoots pretty high with a C motor and is deceptively quick off t' pad in spite o' its stocky nature.

Flight Rating: 4 out o' 5

Summary:
Excelsior's line o' "Retro Bash Kits" is a great throwback t' t' old Estes "Goony Birds", me hearties, matey, matey, either for those who thought they were cool then or for people like me who think they're cool now.

PROs: High coolness factor and awesome decals. Avast! These rockets are fun t' build, ya bilge rat, fun t' brin' t' t' range, shiver me timbers, fun t' fly and fun t' talk about. Blimey! Everyone needs at least one Goony in their lineup!

CONs: No fin markin' guide for t' 3 fin configuration. Aye aye! Potential decal "gotcha" if t' normal launch lug placement is used.

Overall Rating: 4 out o' 5