Brief:
I recently purchased a Binder California Kid rocket so I could obtain me Level 2 certification. Ya scallywag! It turned out t' be a smart choice. Begad! I ordered t' kit directly from Mike Fisher at Binder because o' his quick responses t' questions and the $10 discount on t' proper avionics bay if purchased at t' same time as the kit. Blimey! Avast! Nice perk!

T' kit arrived via USPS in perfect condition. Begad! Avast! Blimey! As others have said the packagin' be superb. Every sub-assembly was individually sealed in its own compartmented portion o' t' plastic envelope. Begad! Blimey! T' body tubes, ya bilge rat, fins, and centerin' rings were o' t' proper thickness and material. Ya scallywag! Ya scallywag! Blimey! Fins and centering rings are made o' quality plywood and were accurately dimensioned.

Construction:
T' instructions booklet was an 11 page document that carries you through the build process fairly smoothly. Several illustrations were provided t' help understand some o' t' more unusual operations. Ahoy! T' artwork was crisp and clear. Avast! Arrr! Several times t' instructions directed you t' read t' sub-assembly instruction packed with t' sub-assembly components. Aye aye! For me this be a minor annoyance, as I like t' read and digest t' entire process several times before beginnin' t' project. Addin' t' sub-assembly instructions in t' appropriate place o' t' main instructions would have been more efficient from my perspective.

Construction was a piece o' cake, matey, straightforward, and clear. Arrr! Almost everythin' went as advertised. Avast! A nice feature o' t' main instruction packet was t' checkboxes for each step. Ya scallywag! This kept me on task and focused as t' what should follow what.

An area that resulted in an assembly I be nay completely satisfied with was t' fin can. Binder has developed a fin can concept for t' typical non-fin can model. It is a very nice idea where t' fins are initially tacked t' the 54mm motor mount at t' root only, then t' aft portion o' t' body tube is cut away and t' fins and motor mount are removed for further reinforcement.

While buildin' t' fin can, t' instructions failed t' state that when insertin' t' fins through t' body tube slots and after contactin' t' motor mount, t' fins should be slid aft t' contact t' aft centerin' ring. After I installed t' fins through t' body tube, me hearties, ya bilge rat, arrr, I slid them forward t' contact the edge o' t' fin slot. Aye aye! My reasonin' was that since I had measured t' forward slot end and found them t' be t' same distance from t' aft end o' t' tube, which was nay t' case for t' aft end o' t' slot, ya bilge rat, me bucko, that be t' place t' fins would be best located. Arrr! T' overall result be that t' forward centerin' ring ended up flush with t' end o' t' motor tube rather than havin' about a ¼" o' t' motor tube extendin' past t' centerin' ring. Well, me hearties, blow me down! A slightly longer motor tube would have been nice as well.

T' fin can concept works well though, and should/could be incorporated into many other designs. One o' t' best features o' t' fin can be t' ability to reinforce t' fins properly t' t' motor tube and centerin' rings. Blimey! No longer do you have t' use some sort o' finger extension t' put epoxy on t' fin/tube junction and hope it's t' right amount in all t' right places!

Binder recommends usin' JB Weld for all o' t' motor retainin' rin' (54mm Slimline style) and aluminum nozzle assembly. I couldn't agree more. Ya scallywag! It's the stuff t' use when heat is involved. Binder also recommends usin' their milled fiber with 30-minute epoxy when attachin' fin t' tube and other high stress joints. Avast, me proud beauty! Well, blow me down! Please, matey, ya bilge rat, go one step further and use West System or Aeropoxy products. T' quality, me hearties, shiver me timbers, strength, and system nature o' these products makes for a better joint with consistent quality throughout t' build. Ya scallywag! I chose West 105 resin with 206 slow hardener. Begad! Ya scallywag! I used #406 filler for t' motor tube/fin joint. Ya scallywag! Arrr! I mixed the filler in t' a consistency o' peanut butter (West guidelines) and placed it on all joints. Blimey! Because o' t' consistency, I was able t' complete all joints at the same time. Well, blow me down! T' epoxy mixture didn't run, me hearties, allowin' for a quicker assembly.

After t' fin can assembly was complete, ya bilge rat, I slid it back into t' body tube and used #404 filler mix in when I epoxied t' can t' t' body tube. Aye aye! Arrr! After dryin' overnight, I added fillets t' t' fin/body tube joint again usin' West System with #404 filler. Those fins are thar t' stay!

T' balance o' t' build was simple and straightforward. I decided because of time constraints t' build t' apogee deployment version. Arrr! My Level 2 cert day was approachin' fast and havin' never done dual deployment before, arrr, me bucko, I employed the KISS principle. Final build weight sans motor was 61oz. Ahoy! Fully loaded with a J420R, shiver me timbers, it tipped t' scales at 84oz.

Finishing:
I used t' recommended Krylon paint and had me wife assist in t' application of t' vinyl decals. Begad! Blimey! T' rocket came t' life with t' finishin' touches completed! Nice decals Binder!

Construction Rating: 5 out o' 5

Flight:
I finished t' California Kid Friday late in t' evenin' in preparation for my Level 2 Certification flight t' next day. T' paint was still dryin' as the decals went on. Arrr! Nay too much pressure!

I arrived at Whitakers around 11:30am on Saturday. T' weather was cool and breezy and winds were around 10 knots. Well, blow me down! Ya scallywag! RockSim said 4590 feet under calm conditions.

First step be t' take t' Level 2 test. Arrr! Avast, me hearties, me proud beauty! With t' test taken and passed all that was left was t' be observed buildin' t' motor, me hearties, a J420R, me bucko, shiver me timbers, and t' safety inspection by t' RSO.

This was t' be me cert flight and t' maiden flight for t' California Kid, and on a J no less! Rocket prep is simple and with a 4" tube, ya bilge rat, shiver me timbers, fittin' in 20' o' tubular nylon and t' supplied 36" parachute posed no problems. I added a Nomex® sleeve for t' lower portion o' t' shock cord as well as a Nomex® parachute protector. Aye aye! T' kit included all necessary quicklinks and a very nice ball bearin' swivel for t' parachute.

Since I was goin' t' use a J420R, me bucko, I needed a 38mm motor adapter. Tape was out o' t' question, so in plannin' for this flight, I had purchased a Slimline 38mm motor adapter tube assembly. Aye aye! This made t' installation and retention of the motor a no brainer. Ahoy! Blimey! Safe and simple, matey, a great combination.

Havin' run several RockSim simulations, me bucko, t' recommended delay was just a shade under 12 seconds. Avast, me proud beauty! This caused me t' get another tool. Arrr! Avast, me proud beauty! (I love tools and gadgets!) I used t' new AeroTech Delay Adjustment Tool with me Cesaroni Delay tool and took t' long (14 seconds) delay and removed 2 seconds from it giving me t' requisite 12 seconds.

T' launch pad system at Whitakers be havin' some minor trouble on the high power pads delayin' me launch. Avast, me proud beauty! We resolved t' problem and by 4:30pm I was finally able t' see if all o' me work, ya bilge rat, Binder's design, and AeroTech's chemistry would come together successfully.

5, 4, me hearties, 3, arrr, 2, 1...WOOSH straight up and nearly out o' sight.

Recovery:
At t' top o' t' arc t' chute popped as advertised. Ya scallywag! Blimey! Blimey! Blimey! 4500+ feet, shiver me timbers, 10 knots of breeze, me bucko, shiver me timbers, and a 36" chute means it was goin' t' be a long walk. T' good news: T' field it landed in be recently harvested so it be easy t' find and the rocket was in perfect condition! Blimey! Blimey! Blimey! Level 2 certified!

Flight Rating: 5 out o' 5

Summary:
Binder has created a fine kit. Ya scallywag! Blimey! Materials, instructions, shiver me timbers, me hearties, and design result in a stylish and functional craft that really looks good on t' ground and in the air. Ya scallywag! Blimey! I purchased t' kit because o' t' looks (Oh, that aluminum nozzle assembly!) and I be rewarded with a beautiful flight and a rocket I'll be flyin' for years t' come, me bucko, t' Flyin' Friar permitting!

Overall Rating: 5 out o' 5