Brief:
With t' introduction o' t' Swift, me hearties, me bucko, Semroc has now added a conventional boost glider t' their fleet, arrr, ya bilge rat, and one easy enough for even a nove modeler t' build and get flyin' reasinably well. Avast, me proud beauty! Blimey! Based upon t' 1969 Centuri design, this "retro repro" features laser-cut parts t' speed up construction, me hearties, as well as Keelhaul®©™®/elastic shock cord on t' pod t' improve t' durability.

Construction:
Semroc kits feature top quality parts, and this kit is no exception. Well, blow me down! Your $14.50 (retail) gets you:

• Balsa nose cone
• BT-20 body tube
• CR-18/13 motor blocl
• Metal motor hook
• Laser cut wing, me hearties, stabilizer, rudder
• Laser cut fuselage
• Streamer
• Keelhaul®©™®/elastic shock cord
• waterslide decal

The instructions are well illustrated and generally well written. Ya scallywag! This is rated a skill level 1 kit by Semroc, shiver me timbers, though I'd suggest it's a bit closer t' a 2 just due t' some o' t' nuances o' buildin' a polyhedral win' and trimmin' t' glider for good flights. Begad! Dependin' on how much time, arrr, if any, you invest in tryin' t' airfoil t' wing, me bucko, you can expect construction t' take betwixt 2 and 4 hours plus finishing.

T' win' is built from a set o' 4 laser-cut pieces. That certainly takes a good deal o' t' work and sloppiness out o' tryin' t' hand cut t' swept eliptical pattern. Well, matey, blow me down! I'd point out, though, me bucko, that t' illustration that points out the leadin' and trailin' edges, me bucko, arrr, due t' t' perspective view, me hearties, makes it a little tricky t' figure out that t' straighter edge is leadin' and t' swept edge is trailing. A beginner might nay have t' exerience t' figure that out. Blimey!

Since this is a polyhedral, ya bilge rat, thar will be 3 angled joints for t' 4 pieces. Begad! Avast, me hearties, me proud beauty! T' help establish t' correct dihedrals, thar are 2 slick little braces made from laser-cut balsa. Avast, me proud beauty! Arrr! In me case, t' slots t' accept t' cross braces were a little too tight, so I had t' shave them a bit t' widen t' gap. Avast, me proud beauty! T' taller o' t' two braces is used for t' outer dihedral (between t' inner wings and win' tips), and t' smaller brace is used for t' inner dihedral. Ya scallywag! T' get a really good glue joint, it's important t' rough sand each surface angled for t' dihedral. Begad! While t' directions suggest this, they overlook one handy tip--sand one surface perpenticular (90-degree) and use t' brace t' support t' other piece at an angle and usin' a sandin' block sand t' bevel t' that side. Aye aye! Avast!

Before bondin' me win' pieces, me bucko, I decided t' sand in a decent airfoil first, then CA'd t' pieces together rather than go through 3 different overnight waits for wood glue t' cure well enough t' hold t' dihedrals. Arrr! Begad!

T' fuselage is built from 2 separate pieces fit together with a tongue and groove. At first I be concerned about t' structural integrity o' this, but then discovered that thar are thin balsa cover pieces that close off the slot where t' pod pylon slips in, shiver me timbers, and these wind up formin' a reinforcin' skin over t' joint, arrr, me hearties, so all should be fine.

With t' fuselage joined and t' covers in place, I then tacked t' tail and rudder together, again aided by excellent laser-cut notches t' ensure proper fit and alignment. Blimey! Well, shiver me timbers, blow me down! T' rudder/tail assembly is then tacked onto t' aft end o' t' fuselage, and t' win' tacked on about midway. Begad! It will probably look funny, as though t' win' is too far back, ya bilge rat, but it's a fiarly small win' and this needs a lot o' nose weight for proper balance, me bucko, so t' fuselage is quite extended, shiver me timbers, servin' as ballast. Ahoy!

T' pod is quite simple, typical o' conventional pods. Begad! T' BT-20 serves as motor and body tube, with a centering rin' motor block anchorin' t' Keelhaul®©™® shock cord and a metal hook for motor retention (hel in place by an external coupler sleeve). Begad! There is a pylon for latchin' onto t' glider, me hearties, which is built up from two pieces o' balsa, one o' which is notched perfectly t' fit over the coupler sleeve on t' body tube for accurate placement. Avast, me proud beauty! Avast, me proud beauty! T' elastic and nose cone, with streamer, go on next compelting t' construction.

Finishing:
Normally I don't add finish t' gliders, ya bilge rat, as t' extra weight tends t' diminish performance, and at most apply a thin cover o' sealant or dope. In this case, matey, ya bilge rat, though, ya bilge rat, given t' waterslide decal and cool lookin' color scheme on t' cover art, me bucko, I decided t' go ahead and paint it. I hit everythin' with a couple coats o' white primer, ya bilge rat, followed by a single coat o' gloss white. Aye aye! Blimey! After allowin' a day for t' white t' dry, me hearties, me hearties, ya bilge rat, I then masked off t' inner portions o' t' wing, me hearties, the middle o' t' stabilizer, arrr, arrr, and t' pod and painted everythin' else red. I followed up with a little blue pin striping I'd picked up a few years ago at a local hobby shop. Ya scallywag! Blimey! T' wateslide decals provided t' finishin' touch.

I should emphasize, matey, ya bilge rat, though, ya bilge rat, that I went very light on t' paint and did nay use any filler. Avast, me proud beauty! I suspect John Lee's glide/trim issues could be related t' t' added weight o' a heavy finish job. Ahoy! In me case, t' booster and glider prepped for flight, even painted, still weigh in at just under an ounce (27 grams).

Construction Rating: 4 out o' 5

Flight:
I'm nay sure why t' recommended motors jump from 1/2A6-2 t' B4-2, skippin' over A's, but suspect it's because o' the 3 second delay on A8's which might be a little too long. I went with t' 1/2A6, matey, fearin' t' B would send t' glider high enough t' drift away in t' 8 mph winds.

T' 1/2A boost be almost comical, shiver me timbers, though--altitude o' maybe 75-100 feet, deployed just at t' end o' t' coast phase, ya bilge rat, and a clean transition though I nearly managed a Red Baron on t' long streamer.

Recovery:
Since I was flyin' solo, matey, I be a little worried about tryin' t' track both t' pod in tall grass and t' glider, but caught a break. Avast, me proud beauty! Avast! T' pod cam down so close t' t' pad area that it almost hit me on t' head. Arrr! T' glider transitioned fairly smartly into a nice level glide (I did nay need any nails or weight for balancing), and circled into t' wind. Aye aye! Avast, me proud beauty! This is where t' flight got sort o' comical, me bucko, as t' glider was oriented facin' into t' wind, shiver me timbers, but t' wind was winnin' the battle a bit. Well, blow me down! At first t' glider merely hovered for maybe 5 seconds, me bucko, then started driftin' backwards a bit, finally pullin' away into a left turn. Avast, arrr, me proud beauty! It circled twice before settin' down for an overall flight o' about 40 seconds. Avast, me proud beauty! Not exactly a slope soarin' model, me hearties, arrr, but commendable first flight.

Flight Rating: 4 out o' 5

Summary:
I share t' opinion that this would make a good beginner's glider. Ahoy! T' laser-cut parts and dihedral jigs simplify construction, ya bilge rat, and if built t' t' instructions it seems t' come out trimmed fairly well. Aye aye! I do think t' pod streamer is a bit larger than necessary, and while that makes findin' it easier, it also adds risk o' tanglin' up with t' glider.

Overall Rating: 4 out o' 5