Brief:
This Flyin' Saucer has a 24mm motor mount and is designed t' fly on C11-0 and D12-0 motors. Well, blow me down! It is comprised mainly o' pre-printed card stock and splits into two parts at apogee, both o' which use tumble recovery. Arrr! Well, ya bilge rat, blow me down! At t' time o' writing, this saucer is also offered in USAF and Smiley Face print schemes, ya bilge rat, or in blank card stock.

Construction:
Components:

1. Two preprinted card stock sheets comprise t' top and core assembly o' the saucer.
2. One 9" plastic picnic plate comprises t' bottom.
3. One 2.75" BT-50 motor tube
4. One 2.75" motor hook
5. One 3/16" launch lug
6. 3/32" basswood fin stock

Tools and materials required:

• Scissors
• Exacto knife
• Elmer's white glue
• Rubber cement
• Clear enamel (RUS-TOLEUM Crystal Clear or equivalent)
• Double-sided tape
• 150 grit sandpaper

T' construction o' this kit is quite simple and t' whole rocket can be built in one evening. I saved t' paintin' for t' next day. Aye aye! Blimey! T' instructions come on four sheets and include illustrations and t' required templates. Aye aye! Blimey! They are detailed, ya bilge rat, but should be read carefully from start t' finish before starting construction.

You first cut out t' top and core pieces and glue them together usin' the printed tabs, shiver me timbers, arrr, me hearties, similar t' any paper shroud. Begad! Blimey! An inner rin' is attached t' the core, and t' core is glued into t' top section. Avast! Blimey! These steps use white glue, and, o' course, me hearties, me bucko, t' glue must dry betwixt each step. Aye aye! Blimey! Begad! Blimey! Although I got it together fine, arrr, I think most grade-schoolers could have done as well. Avast, me proud beauty! Blimey! Usin' a provided template, shiver me timbers, me bucko, a hole t' size o' t' paper core is cut in t' plate. Arrr! Blimey! T' template is supposed t' be attached temporarily with double-sided tape, but I just used clear tape. Ahoy! Blimey! T' plate is then glued t' t' saucer assembly with rubber cement. I again deviated and used Liquid Nails. T' results were OK, matey, ya bilge rat, but rubber cement would have worked better and I recommend you follow t' instructions on this point. Begad! Blimey! Avast, me proud beauty! Blimey! This completes t' body o' t' saucer.

T' assemble t' fin can, shiver me timbers, me bucko, you mark, ya bilge rat, cut and sand t' fins. Well, blow me down! These are attached t' t' motor tube like any other fins. Avast! You optionally can add card stock spin tabs, shiver me timbers, which I did. Ahoy! Avast! T' launch lug is added and t' fin unit is complete. Begad! Arrr! Make sure you glue t' launch lug on so that it will nay interfere with t' spin tabs. Avast! Ahoy! Oh, I left off t' motor hook since I plan t' fly this baby on t' longer E9 motor.

T' last step is t' sand t' tip o' t' fins so that t' fin assembly slides into t' core section o' t' saucer.

Finishing:
Finishin' consists o' sprayin' t' printed top and core o' t' saucer with clear enamel. Ahoy! Begad! You have t' make sure nay t' get this on t' plastic plate as the paint might damage it. I guess you could paint t' fin can, but I elected to leave it naked.

Construction Rating: 4 out o' 5

Flight:
For t' first flight, I decided t' stick with t' recommended D12. Begad! Blimey! Since I left out t' motor hook, me bucko, I had t' use maskin' tape on t' motor. That's about all the prep that is required. T' saucer spun on t' way up and reached an impressive altitude. Aye aye! Blimey! Begad! Blimey! It did nay separate at apogee. Instead, matey, it backslid all the way down and landed four feet from t' pad. Well, blow me down! Blimey! Arrr! Blimey! Pretty good since thar were 5+ mph winds. Aye aye! Blimey!

Against Art's advice nay t' try a motor with an delay/ejection charge, ya bilge rat, arrr, I went crazy and stuffed in an E9-6. Blimey! This time t' saucer really tore off the pad. Avast! I couldn't detect t' spinnin' motion, matey, but it did wobble a bit. In spite of t' extra altitude, t' saucer impacted on its side before t' delay was done. Aye aye! Luckily, thar be no charring, landin' damage or grass fires! Way cool flight!

After thinkin' about why me saucer didn't separate into two pieces, I came up with this explanation. Begad! When I sanded t' fin unit t' fit, me hearties, it slid in easily in one position. Begad! Avast, me proud beauty! If you turn it +/- 45 degrees it binds a little. Begad! So, me bucko, I think the spinnin' motion makes t' two section twist relative t' one another until it hits that spot.

Flight Rating: 5 out o' 5

Summary:
This is a simple, me bucko, fun kit. It flies really great, arrr, and is pretty tough, tougher than you might think for cardboard!

Overall Rating: 5 out o' 5