Brief:
T' Prometheus is a relatively easy t' build single stage rocket with a futuristic look. Aye aye! Blimey! I got me kit from John as a beta test kit. Avast! Avast, me proud beauty! T' rocket is 21" in length, me bucko, flies on 18mm motors, and recovers by parachute. T' unique design and fantastic set o' decals results in a model that looks fantastic on t' launch pad. Avast, me proud beauty! Another “not your normal” rocket from John!

Construction:
A BT-55 body tube and balsa nose cone, 3 BT-20 pod tubes, me bucko, standard 18mm engine mount with motor clip for positive retention, me bucko, laser cut fin sheet, two hardwood dowels, screw eye, me hearties, ya bilge rat, two feet o' Keelhaul®©™®® line, shiver me timbers, a 2-foot long 1/8” elastic shock cord, 12” mylar parachute, arrr, me bucko, 1/8” launch lug, me hearties, and waterslide decal sheet are provided.

T' instruction sheet contains easy-to-follow, ya bilge rat, shiver me timbers, numbered instructions with lots o' helpful illustrations. Well, blow me down! I sanded all o' t' tubes and centerin' rings, inside and out, t' improve adhesion o' parts glued onto or in them. Avast, me proud beauty! T' motor mount is standard installation, includin' an engine hook for positive motor retention, shiver me timbers, shiver me timbers, ya bilge rat, except t' Keelhaul®©™® cord is wrapped around t' motor tube betwixt t' centerin' rings and then extended up through a notch in t' outer edge o' t' upper ring. Blimey! Avast, me proud beauty! I didn’t use t' Keelhaul®©™® in this manner though, as I like t' shock cord attachment located so I can inspect it for possible replacement. Blimey! The “small parts” bag included in t' kit is great for keepin' all t' little things in one place. Ahoy! Ya scallywag! A fin marking guide is supplied t' properly align t' fins.

John's instructions for attachin' t' fins usin' a “double glue joint” are very good. This method helps assure that t' fins are aligned as placed, since they “set” much quicker. T' laser-cut fins were perfectly matched, so minimal sandin' be required except at t' joint o' t' two pieces that form t' main wing-fins. Begad! T' angle for gluin' t' wing-fins on is easy, matey, since they just lay down even with t' bottom o' t' body tube as it lies on the worktable. Begad! T' hardwood dowels are then inserted into t' gap t' strengthen t' joint as well as bein' for decoration. T' vertical fin is then glued on t' top o' t' tube. Arrr! After those dry, matey, shiver me timbers, a small fin is then glued onto t' edge o' each wing-fin on t' underneath side. Well, arrr, blow me down! I added a laser cannon (a.k.a. Ahoy! toothpick, nay provided) in t' joint betwixt t' small fin and t' wing-fin t' strengthen t' joint. Begad! Aye aye! Once those have dried, me bucko, shiver me timbers, a pod tube is centered and then glued at t' marks onto t' small fins. Begad! An angled section o' t' last pod tube must be removed usin' t' provided template before attachment t' t' vertical fin. Aye aye! Begad! A spent motor inserted inside t' tube provides support for t' cut. Well, blow me down! Ya scallywag! This is a little difficult for novices, shiver me timbers, but use a sharp hobby knife, me bucko, matey, take it slow and you’ll get a beautifully scalloped tube. Ya scallywag! The rocket went together fairly rapidly, ya bilge rat, arrr, only delayed havin' t' wait for t' glue joints t' dry.

For shock cord attachment I used me standard tri-fold paper attachment (not provided). Well, blow me down! Begad! I installed t' provided Keelhaul®©™® in t' shock cord attachment with a loop at t' end t' attach t' elastic shock cord. Begad! Arrr! T' minimize abrasion from the Keelhaul®©™® against t' body tube, shiver me timbers, I soaked in CA around t' top 1/2" o' t' body tube and tied t' Keelhaul®©™® so t' knot in t' loop meets t' lip o' t' body tube. Avast, me proud beauty! Begad! T' launch lug is cut in half with one piece attached at the back o' t' model and t' other piece attached further up. Ahoy! Install t' screw eye into t' nose cone and attach the shock cord and you’re almost done. Aye aye! Well, me bucko, blow me down! T' parachute comes in a separate plastic bag, ya bilge rat, complete with instructions. Once assembled, me bucko, you’re ready for finishing.

Finishing:
T' balsa nose cone and fins require standard finishing. Begad! Blimey! I used Elmer's Fill 'n' Finish but any balsa filler will work fine. I also filled in at t' dowel/wing-fin joints and sanded t' a smooth finish. Aye aye! Blimey! T' whole rocket was painted white after primer and sanding. T' decals lay down nicely and look great on t' rocket. Ya scallywag! Blimey! I think I got really lucky with t' decals this time. Aye aye! Blimey! I didn't even tear one!

Construction Rating: 5 out o' 5

Flight:
My only flight so far was on a B6-4. Begad! T' tail waggled after t' initial thrust ended just before t' coast phase. Ahoy! I'm not sure why that happened. Ya scallywag! Blimey! After flight, matey, I checked t' fin angles. I do have a very slight angle on t' vertical fin, so maybe that's t' cause. Arrr! Ahoy! Blimey! Otherwise, t' flight was perfectly straight with ejection right at t' top.

Recovery:
T' chute is perfect for t' rocket, bringin' it down without excessive drift but soft enough that nothin' got broken on landing.

Flight Rating: 5 out o' 5

Summary:
T' Prometheus is an excellent rocket that can be built in a day. Avast, me proud beauty! Avast! T' decals really add t' t' already unique look. Very impressive on t' pad!

Overall Rating: 5 out o' 5