Brief:
Scale, Midpower, me bucko, shiver me timbers, Parachute Recovery

Sheri's Mercury Redstone is an impressive lookin' rocket on her website. It's also fairly impressive when t' box shows up on t' doorstep. Avast, me proud beauty! Begad! Blimey! After delayin' for a while, I decided t' get this one started.

Construction:
T' first step in construction is t' read through t' instructions. They are long, ya bilge rat, but easy t' read and doin' so helps one understand steps that will upcoming.

T' first real "construction" thin' t' do is t' fish out the two plywood centerin' rings and a 3/4" square o' plywood. T' plywood was epoxied onto one o' t' rings in order t' strengthen it for t' mountin' o' an eye bolt for t' recovery harness. Ya scallywag! I used 15 minute epoxy here because I grabbed t' wrong bottles.

When t' epoxy was set up, me hearties, I be instructed t' drill a hole through t' center o' t' block and through t' rin' t' which it be mounted t' receive t' bolt. A 1/4" hole be drilled.

T' hole bein' drilled, shiver me timbers, it was a simple matter t' insert t' receiver for t' bolt and epoxy it into place. It's teeth were forced into t' plywood with a pair o' pliers. Blimey! Blimey! I mixed some five-minute epoxy and prepared t' seat t' bolt. Arrr! Blimey! Unfortunately, matey, I did nay pay enough attention and mounted t' receiver on t' wrong side. Ya scallywag! Blimey! By t' time I had discovered what I had done, it was too late and t' epoxy had set.

T' centerin' rin' without t' bolt was mounted in t' body tube flush with one end. It was mounted with five-minute epoxy and a fillet was applied around t' perimeter.

T' other centerin' ring, shiver me timbers, t' one with t' bolt, me hearties, was mounted in t' body tube six inches from t' forward end. Arrr! Arrr! It too was mounted and filleted with five-minute epoxy and it be ensured that t' rin' o' t' bolt was facin' forward.

T' kit came with four plywood fins and a styrene fin template along with a sheet o' styrene from which t' cut...fins! As it happens, t' plywood is just for t' core o' some built up fins.

T' fin template was used t' transfer t' outline o' t' fins t' t' sheet styrene for eight instances. Arrr! Blimey! T' instruction recommended t' use t' template as a guide t' score t' styrene with a razor knife and then flex it t' make clean breaks. Well, blow me down! T' scorin' and flexin' idea worked well for me. Ya scallywag! Blimey! Usin' t' template as a guide t' do this did nay work so well. Blimey! Blimey! For me, me bucko, it be much easier t' use a steel rule as a guide for t' scoring. That kept me poor template in better shape as well.

A fact that may be worrisome, me hearties, for somebody who does nay READ t' instructions, me bucko, shiver me timbers, is that t' styrene fins are somewhat larger than t' plywood cores. Begad! There is a good reason for this. Begad! T' plywood core is set flush against t' base and root edge o' t' styrene. Blimey! T' styrene is then lightly scored with t' razor along t' leadin' edge. Blimey! T' rudders on t' outer edge are also scored and then snapped off and saved for later.

T' styrene along t' angled leadin' edge o' t' fins was scored but nay snapped off. Ahoy! Begad! T' scorin' was t' facilitate bendin' an angle into t' leadin' edge. Avast, me proud beauty! After tryin' several methods o' gettin' this right, me hearties, t' one that worked best for me was t' put t' plywood core into place and then gently bend t' plastic towards t' centerline o' t' fin.

When all o' t' angles were formed, arrr, t' styrene was glued t' t' plywood cores usin' CA. Begad! T' resultin' bevel actually looked pretty good even if it was nay yet "perfect".

At this point, ya bilge rat, t' plywood cores were sandwiched betwixt styrene sheets and bonded with CA. Avast, me bucko, me proud beauty! T' bevels on t' leadin' edges o' t' fins still had t' be dealt with though. Blimey! This was easily done with t' application o' a solvent type o' plastic cement. Ahoy! Aye aye! I used Plastruct. Ahoy! This welded t' leadin' edges together and healed all gaps.

T' Redstone had another little detail betwixt t' fins and t' rudders. This kit builds that "thingamabob" out o' styrene as well. Begad! Blimey! T' template must be cut from t' plan that is provided. Blimey! Blimey! It is then laid on t' styrene t' trace t' outline four times. Begad! Blimey! Ya scallywag! Blimey! I scored t' styrene with a razor knife and steel rule. Arrr! Blimey! I found this much more difficult that cuttin' t' fins themselves.

T' thingamabobs were test fitted onto t' fins and it was found that in each case, me cuttin' left somethin' t' be desired. Ya scallywag! All fit all right towards t' bottom, me hearties, but each had t' have t' top opened up a bit more. When they all fit, shiver me timbers, me bucko, CA be used t' cement them t' t' fin cores. Ya scallywag! When t' CA had dried, solvent cement be used t' join t' plastic t' that o' t' fins.

With t' thingamabobs in place, t' rudders came next. They were formed from t' pieces o' styrene that were cut from t' fins a few steps before and assembled in a similar manner. Well, blow me down! I held each piece flush against t' bottom and inner edges and used t' razor knife t' score a line. Ya scallywag! Blimey! Half were scored on one side and half on t' other. Ahoy! Avast! Blimey! T' plastic be then gently bent t' form t' angle usin' t' plywood core as a straightedge.

After bending, t' styrene rudder tabs were glued t' t' plywood cores with CA. Begad! When t' CA had set, ya bilge rat, me hearties, solvent cement be used t' join t' edges along t' angled leadin' edges and t' joint with t' thingamabobs. T' results were much less than perfect and almost all o' t' problems were with t' thingamabobs. Ya scallywag! Well, blow me down! I had nay gotten them as well as t' other pieces.

Before cappin' off t' rudders, me bucko, me bucko, me bucko, I needed t' clean them up a bit. Ahoy! I used a sandin' board t' take down t' excess material and get t' edges o' t' styrene t' line up with t' edges o' t' cores. Begad! I then used liquid solvent cement t' glue on scraps o' styrene t' t' outer edges, arrr, leavin' plenty o' overhang. Aye aye! When I tried t' remove t' excess material, though, ya bilge rat, I found that t' joint betwixt t' plastic pieces was nay handlin' t' abuse. Arrr! Avast, me bucko, me proud beauty! This was rectified by puttin' a small amount o' CA on t' tips o' t' rudder cores and then solvent weldin' t' edges o' t' plastic.

With t' tips re-applied and now holdin' firm, matey, I trimmed t' excess material by first scorin' around t' perimeter with a razor knife and then usin' t' sandin' board t' remove smaller humps. Ya scallywag! There were a few gaps and bulges but I figured that t' fairin' process would take care o' that.

From a distance, t' fins looked pretty good, matey, arrr, certainly better than most things that come out o' me shop, me bucko, but thar were some flaws that bothered me. Begad! Blimey! A few places had gaps betwixt t' pieces o' styrene. I applied Squadron green putty t' t' offendin' area and let t' fins cure for a few days.

When t' few days were up, I went after t' accumulated goop with a will usin' sandpaper, me hearties, sandin' sticks and a little jewelers file t' get into those tight corners. Ahoy! Begad! A frequent scrubbin' o' t' file with a wire brush was a must as was t' brushin' away o' t' dusty by-products. Well, blow me down! I got it t' t' point where I thought that paintin' would make them look "perfect".

T' kit comes with a fin markin' guide in t' form or a wrap around that is cut out o' t' plan sheet. Aye aye! I cut it out and taped it in place and found that it fit perfectly. T' marks for t' four fins were transferred t' t' body tube and t' guide be removed. Avast, me proud beauty! An angle was then used t' extend t' lines from all t' way t' t' aft t' about 8 inches forward. Ya scallywag! Blimey! A steel ruler was used t' connect opposin' lines across t' after centerin' ring.

T' instructions then had me offset t' fin line by 1/16" t' either side t' accomodate t' width o' t' fins. Ahoy! Blimey! I know its a very minor point but I would have preferred t' have t' correct offset marked on t' wrap around guide. Ahoy! Blimey! This is purely me preference and be t' first real thin' I would change, but it's so minor that I feel silly even mentionin' it. Avast! Blimey! Begad! Blimey! As I said, that would be MY preference.

In any event, me bucko, t' offsets were marked and those lines were extended for t' length o' t' fins. A fresh hobby knife and a steel rule were then used t' score along t' offset lines so that t' vinyl coatin' could be removed in order t' promote better adhesion o' t' fins.

T' instruction made no mention o' this next step but it is somethin' I now do fairly routinely. I used a drill and made a series o' perforations along t' fin lines t' aid in t' formation o' epoxy rivets. Ya scallywag! I did t' same thin' with a smaller bit along t' root edge o' t' fins.

All four o' t' fins were mounted usin' 5 minute epoxy. Avast, me proud beauty! Aye aye! A small batch was made for one fin and then a toothpick was used t' trowel it into place along t' BT. It be also used t' force epoxy into t' rivet holes. Blimey! Ya scallywag! After that, arrr, it was a simple matter t' press t' fin into place, check for alignment and hold it in place until t' epoxy set up stiff enough t' hold on its own. Well, blow me down! T' process was repeated for t' other three fins.

I accidentally got t' forward centerin' rin' a little too far forward so that t' provided motor tube would nay extend far enough; when it was inserted, arrr, in just bared touched both centerin' rings without enough overage t' provide any support. Fortunately, I had a piece o' LOC motor tubin' sittin' around for a project that has yet t' begin and decided t' cannibalize it. Ahoy! Avast! I inserted it so that t' front protruded just a bit from t' forward rin' and then marked t' tube where it had a 1/2" clearance on t' aft ring. Begad! I then made up a mandrel and cut it t' length with a razor knife. T' resultin' tube was slid into place and secured with more five-minute epoxy.

If thar be one thin' that surprised me most about this kit it was t' instructions on filleting. I expected t' fillet t' fins with epoxy but t' instructions said t' used plain old white glue. I decided t' follow t' instructions t' see how it would work out. I began layin' in t' fillets, lettin' them dry, rotatin' t' rocket and doin' it again.

T' tower for t' launch escape system is built up out o' styrene tubing. Arrr! Ahoy! Construction o' t' LES begins with takin' t' plan for one o' t' verticals and cuttin' it out t' serve as a backdrop and template. Avast, me proud beauty! Aye aye! T' template be taped down securely and then three pieces o' 3/16 styrene tubin' were cut t' length usin' t' template as a guide.

T' vertical struts were fabricate one at a time. A piece o' t' styrene cut t' length be taped down on top o' t' template. Begad! Two further pieces o' t' 3/16 tubin' were cut t' t' length o' t' "Y" at t' bottom o' t' structure. Begad! Aye aye! These were then shaved on one end t' achieve t' desired angle. When they fit well enough, me hearties, they too were taped into place on t' template and t' three pieces were joint with Plastruct solvent cement.

While t' solvent be drying, me bucko, matey, a gusset plate t' cover t' joint be cut from .020 styrene. It too was then solvent welded into place over t' joint. After lettin' it sit for a few minutes, t' structure be taken up, me bucko, more solvent applied t' t' opposite side and t' entire procedure repeated twice more. Begad! I should have mentioned that while t' piece was taped down, me hearties, various depth marks were transferred t' t' tower struts with a felt tip.

T' instructions indicated that t' base o' t' tower be t' be fabricated on a plywood ring. Avast, me hearties, me proud beauty! Blimey! I looked in vain for such a piece o' plywood. Ya scallywag! Blimey! I did find a resin rin' but t' inner diameter o' t' rin' be different than that shown on t' plans. Ya scallywag! Avast, me proud beauty! Blimey! I contacted Sheri and she assured me that it was t' correct part and was a result o' a design change. Ahoy! Still unsure because o' t' amount o' play left in t' 1/8" space betwixt t' rin' and t' capsule, ya bilge rat, I contacted Sheri again and be reassured that this be correct.

T' resin disk has a bevel t' it so it must be oriented correctly. Arrr! Arrr! Blimey! I made sure t' beveled side be up and then cut out t' t' template. Aye aye! I taped t' template onto t' upper surface o' t' disk and scrounged around until I found a 3/32" drill bit. Six holes were then drilled in t' places indicated on t' template.

With t' six holes drilled, I test fit t' vertical struts o' t' LES tower but did nay glue them at this time, ya bilge rat, even though this be t' current step in t' instructions. Begad! I wanted t' make sure about t' fit at t' other end first.

T' upper disk o' t' LES tower is made o' plywood. I cut out its template, taped it into place and drilled t' three holes it calls for. Arrr! T' disk was then slid into place at t' upper end o' t' assembly. Begad! Since things seemed t' fit, arrr, both ends were secured with CA.

T' horizontal members o' t' LES trusses are made from 1/16" styrene tubing. Usin' t' plan as a guide for length, ya bilge rat, I cut t' three upper horizontals. I placed them singly at t' marks made earlier doin' one side at a time and usin' Plastruct solvent weld. I let on side dry and then brushed t' other side with a generous amount and squeezed it into place betwixt t' uprights. Ya scallywag! Arrr! Since thar be a bit o' bowing, I used cellophane tape t' hold t' structure tight as it dried.

T' next day, ya bilge rat, I peeled off t' tape and inspected t' results. Begad! It was a start.

Since t' first one worked out, I got started on t' second series o' horizontal members. Blimey! I cut three pieces o' tubin' from t' plan and t' solvent welded them into place, usin' a little tape t' hold t' joints closed. They too came out fine.

While t' solvent welds on t' LES tower were hardenin' up, I got t' work on t' Triple Mini Motor. Aye aye! Blimey! It too was fabricated for styrene tubing. Three lengths o' 3/4" long by 1/16" tubin' were cut t' length specified on t' plans. Ahoy! Blimey! A 3/16" piece and a 1/4" piece were also cut. Begad! Blimey! The three pieces o' 1/16" tubin' were then bundled together and slid inside o' t' 3/16" piece with 3/16" left protruding. Blimey! Blimey! Avast, me proud beauty! Blimey! They were fixed into place with solvent weld. Aye aye! Blimey! Ya scallywag! Blimey! Once t' three pieces were tacked into place, me hearties, me bucko, a razor be used t' separate them and bend t' three small pieces out at a 30 degree angle. Aye aye! Blimey! T' softenin' from t' Plastruct helped with this. Begad! Blimey! This entire assembly be then slid into t' short piece o' 1/4" tubin' that had been cut and solvent welded. Begad! Blimey! T' butt end as gently sanded t' keep everythin' straight.

T' LES tower bein' dry by this point, ya bilge rat, was inverted and set on its cap. T' Triple Mini assembly was then glued t' t' center o' t' base with CA makin' sure that t' mini nozzles were rotated in such a way as t' be centered on t' LES truss panels.

I tried cuttin' t' first set o' diagonal struts from t' plans but that did nay work out too well. Ahoy! Begad! Each was just a bit too long. Avast! Fortunately, Sheri is extremely generous in t' materials she packs. Avast, me proud beauty! Begad! I re-cut t' diagonals purposefully too long and then started trimmin' them t' fit by a short snip at a time. When they seemed t' be t' right length, I shaved a bit on one side o' t' end t' give a bit o' a miter and then put it in place with tweezers and Plastruct. Well, blow me down! Avast! T' lower diagonal struts were placed in t' same manner.

I be pretty happy with t' way t' LES had turned out thus far. It was nothin' like perfect but it did represent one o' me best efforts t' date. Well, blow me down! Ahoy! Blimey! It could, however, ya bilge rat, be improved a bit. This was t' point when t' truss needed t' be faired and t' instructions gave t' option o' Bondo or Squadron Green putty. Blimey! Blimey! I had some o' t' latter and be unfamiliar with t' former so I started pressin' it into place and let it set up for a day.

T' spike at t' top o' t' LES is a built up affair as is most o' this kit. T' top point be formed by takin' a wooden dowel and sandin' a point into it. Aye aye! Blimey! T' point be then separated from t' rest o' t' dowel by rollin' under a razor knife. Arrr! T' base o' t' point was then dressed up a bit with some sandin' and t' point be glued t' t' end o' a styrene tube with CA and set aside.

T' "can" at t' top o' t' LES is also built up. Begad! Blimey! T' kit comes with a short length o' tubin' and this be glued t' scraps o' flat styrene plastic and allowed t' set. Blimey! Blimey! When it be set up, me hearties, excess plastic was trimmed away and then sandpaper was used t' round t' caps even with t' edge o' t' tubing.

A 3/32" hole be drilled in t' center o' both end caps o' t' can. Well, matey, blow me down! T' spike was then slid through t' top hole and into t' bottom hole so that t' tubin' be flush with t' bottom cap. Begad! T' styrene be then solvent welded into place.

Goin' back t' t' LES tower, t' Squadron Green goop had hardened and I began t' process o' sandin' it off. At various points I used sandpaper and a file triangular file. Ahoy! Blimey! Ya scallywag! Blimey! T' X-acto blade was also a friend.

By t' time t' tower was sanded, t' solvent on t' can and spike had plenty o' time t' dry several hundred times over. T' next step be t' begin applyin' t' bands around t' can. These are cut from thin styrene and put into place with CA. Aye aye! T' can be laid alongside t' plan and t' lines were marked. Blimey! Aye aye! T' proper width o' styrene was then cut and one end was tacked into place with CA. I wrapped t' strip around t' can and cut it just a bit longer than needed for a complete circumference. I then whittled and sanded it t' length and finished tackin' it with CA. Begad! Aye aye! I had gotten t' wide band and part o' t' upper skinny band done when I had t' leave off t' deal with a work issue.

T' plans show that t' can has a single wide band and two skinny ones. All o' t' photos, however, show 3 o' t' skinny ones in addition t' t' wide one. Blimey! After considerin' for a while, arrr, I decided that I liked t' looks o' the three better than t' two. Begad! Ya scallywag! So it is that when I got a chance t' work on this one again, ya bilge rat, I finished t' unfinished band and then cut another.

T' next step is what really caused me some confusion. Begad! Both t' photos in t' instruction and t' plans show two pieces o' styrene with a half circular profile runnin' vertically on t' can, me hearties, 180 degrees from each other. Arrr! T' text o' t' instructions makes no mention o' them, however. Avast, me proud beauty! Well, blow me down! At first I thought this would be fairly simple t' take care of. Begad! I laid t' stock material against t' plan and cut two pieces t' lengths. Well, blow me down! Then, because o' t' plan and t' photos, I used sandpaper t' put a rounded point at t' ends o' both o' them.

So far so good. Avast, me proud beauty! Ahoy! My dilemma came when I laid t' verticals along t' can. Well, blow me down! Avast! My intention all along was t' use one o' them t' hide t' seams on t' bands. Avast, me proud beauty! That was fine. Begad! Arrr! T' problem was t' gaps betwixt t' verticals and t' can betwixt t' bands. Blimey! T' instructions did nay say how this be t' be achieved.

I fired off a question t' Sheri expectin' t' hear back from her quickly. Ahoy! Avast, me proud beauty! She had always responded smartly in t' past. Well, blow me down! Avast! This time, heard nothin' after three days so I sent a follow up and heard nothing. I then remembered that me first message had come durin' t' National Sport Launch and I figured that she might be attending. Ya scallywag! She may also have decided t' take some vacation time afterward. Avast! I had t' leave town for a week so I decided t' wait and see what was waitin' for me when I got home. Well, blow me down! When I did get home, arrr, thar was nothing.

Although it seemed a forlorn hope, me hearties, I decided t' get t' work again on t' off chance I could have this rocket ready for me next club launch. Well, blow me down! Blimey! I laid a vertical against t' can and marked with a pencil where t' bandin' was. Ya scallywag! Blimey! I then used a combination o' file and razor knife t' try and remove material. Well, blow me down! Blimey! Arrr! Blimey! It be slow and painstaking. Ya scallywag! Blimey! I finally got t' t' point where I realized that it was nay goin' t' get any better with MY skills and put t' first vertical in place with Plastruct. Begad! Blimey! It looked OK from some directions but thar are some big gaps as well. I decided t' wait just a bit more before tacklin' t' other one.

Still wantin' t' work on this one a bit more, matey, I took t' cast resin nozzles for t' LES out o' t' bag. Two were connected by way o' a sprue and t' third was free and slightly lighter shade. Avast! That posed no problems at all since they are all meant t' be painted. Arrr! I trimmed off t' excess flash with a razor and then sanded them into round.

Bein' a naturally impatient person, matey, me hearties, me hearties, I decided nay t' wait any longer and t' try and place t' second vertical tube in t' same way as t' first. Blimey! Blimey! T' results were much t' same and looked OK from a distance but did nay bear close scrutiny. Aye aye! Blimey! Ahoy! Blimey! Naturally, I heard from Sheri after I had completed t' step.

As it turns out, matey, she was nay on vacation but be moving. Ya scallywag! Blimey! Havin' lived through that chaos, shiver me timbers, I understand t' time it took t' get back t' me. Aye aye! Blimey! In any event, t' recommended procedure was none other than what I had already done except for t' quality o' craftsmanship. Begad! Blimey! Aye aye! Blimey! That part is just goin' t' take me some more time until me skills get up there.

Since I was unhappy with t' gaps betwixt t' vertical tubes and t' can, arrr, I used Squadron Green putty t' try and fill them. Begad! I forced it into t' gaps and let it dry for a day. Ya scallywag! Then t' work o' sandin' it down began. Ya scallywag! Avast, me proud beauty! As I feared, this be t' difficult part because o' me own ineptitude and, matey, probably, because I lacked t' proper tools. Begad! I'm nay even sure what t' "proper" tools are. Avast, me proud beauty! Begad! I used a combination approach sanding, carvin' away with an X-acto and foldin' t' sandpaper into semi-stiff little pieces t' get into t' tight areas. Ahoy! Arrr! Eventually, shiver me timbers, it was as good as it be goin' t' get under me auspices. T' green looked hideous t' me but I kept remindin' myself that it would be hidden by t' paint and that it looks better than t' gaps.

With t' can completed, t' next step be t' affix it t' t' LES tower. Arrr! I set it into place and noticed immediately that it was nay sittin' straight. Blimey! Ya scallywag! Blimey! A close examination revealed that one o' me vertical tower struts was just a touch too long. Ya scallywag! Avast, shiver me timbers, me proud beauty! Blimey! Since it had already been glued t' t' cap with CA, I could nay adjust t' cap. Avast! Avast! Blimey! I tried t' remedy it some what by filin' and sandin' down t' high side o' t' cap a bit. Well, blow me down! Blimey! Blimey! I probably should have done more but eventually I placed t' can with a few drops o' thick CA.

At this point I thought I was finished with t' LES...but somethin' looked off. Begad! Then I noticed t' LES nozzles sittin' on t' desk. Begad! Each o' these was glued into place with some thick CA. Begad! Well, blow me down! I recommend doin' it a few times without t' CA and lookin' at it from several angles t' make sure t' bevel is straight; then use t' CA. And that completed t' LES.

Finishing:
T' LES tower be primed with 2 coats o' Testor's gray primer. Well, blow me down! That made an immediate difference in t' appearance as it made everythin' uniform and nay t' sick mixture o' green, shiver me timbers, white and wood product. T' instructions on t' can said that I had t' paint within 2 hours or wait 2 days. Avast, me proud beauty! Blimey! Lookin' t' LES over, arrr, I did nay see where sandin' would be an issue so I gave t' entire structure 2 coats o' Testor's Competition Orange. Ya scallywag! It be actually startin' t' look like somethin' good was goin' t' come o' this endeavor.

Upon examinin' t' decals and finishin' brochure, me bucko, I decided t' go t' easy route and make me rocket a "Liberty Bell 7". Blimey! Blimey! Begad! Blimey! Blimey! Blimey! T' finishin' guide contains a lot o' information on t' various Mercury capsules. Well, blow me down! Blimey! Blimey! Blimey! I am nay quite so ambitious as t' try t' implement it all but it is all appreciated.

I started t' decal process on t' LES with two simple ones, a large and small version o' t' Grand Central Rocket Co. data. Aye aye! Avast, ya bilge rat, me proud beauty! T' larger went on t' side o' t' can and t' smaller on one o' t' nozzles.

Not long after gettin' t' first two decals in place, I realized that I had skipped a step. I brought out some Tamiya silver acrylic paint and painted t' little tubes in t' middle o' t' bottom o' t' LES as per directions.

T' acrylic was given a few minutes t' dry and then t' rest o' t' nozzle writin' decals were put onto t' LES as well as t' small GCR logos.

A few days later, I had t' chance t' apply t' large GCR logos t' t' can. Unlike t' text, these were highly visible. Blimey! One was applied t' each side.

T' resin capsule needed me attention since it had been languishing. Avast! T' instructions called for it t' be rinsed in a 50-50 solution o' bleach and water t' get rid o' mold release agents. Ahoy! Begad! I just used straight clorox and then rinsed it. After it was dried, me bucko, I set it up in t' booth and applied Testor's gray primer. Begad! It be about this time I realized that I had forgotten t' install t' eyescrew so a hole be drilled in t' bottom, a bit o' epoxy put in place and t' screw was tightened into place.

T' body o' t' rocket itself was given a gentle sandin' with #400 paper and then brushed off. Ya scallywag! It be then placed in t' booth and primed with Testor's gray.

T' primer got two days t' dry and then it was lightly sanded. Well, blow me down! Ya scallywag! Blimey! T' body o' t' rocket be then painted with two coats o' Testor's gloss white. Arrr! T' capsule be likewise sanded and then treated to two coats o' Testor's gloss black.

I gave t' main body o' t' rocket a close inspection after t' white paint had dried and found some issues. Ahoy! Some o' t' styrene needed t' be tacked down better and I did this with t' judicious application o' some CA.

I also found some places where t' white paint had nay completely covered t' gray primer. Begad! It was back t' t' booth for more spraying.

T' white had almost a week t' dry before I began any maskin' for t' black roll pattern. Blimey! Begad! I used a combination o' tape and foil t' make what I hoped was a fair approximation o' t' pattern on t' instructions. Ya scallywag! Well, blow me down! Then it was off t' t' booth t' spray t' black. Ya scallywag! When t' maskin' be peeled off, thar were a few places where t' black had misted lightly over t' white but it was nothin' I could nay easily fix. Begad! It came out better than I had hoped.

I have never been quiet about me preference for decals over stickers. Aye aye! T' markings for t' capsule on this kit were all waterslides and that be fine by me. Aye aye! T' markings for t' main body, matey, though, were stickers. Ya scallywag! Avast! They made me rethink me position, at least in terms o' vinyl and large projects.

I decided t' attempt t' large wrap at t' top o' t' body tube first. Arrr! I used an angle t' lightly mark a straight line with a pencil and then peeled t' backing. Aye aye! I be also a bit annoyed that t' sticker had some paper t' peel off o' t' front as well. I be t' learn that this is a GOOD thing. Well, blow me down! Blimey! I lined t' edge o' t' sticker up with t' line I had marked and with t' top o' t' BT and then gently applied it around t' circumference. Well, blow me down! I was pleased with t' way it looked but just a little bit ticked that it did nay wrap all t' way around. Avast, me proud beauty! Well, blow me down! There was a gap o' about 1/8" inch that, fortunately, was on t' white part o' t' roll pattern.

Next up was t' large letterin' for "United" on both sides o' t' rocket. Aye aye! T' me horror, me bucko, I realized that these were individual letters and nay a single sticker and I just KNEW that I would never get t' letterin' lined up right. Ahoy! Begad! I began t' transfer tick marks onto t' BT with a pencil, arrr, arrr, knowin' I would have t' go back and paint or erase them out. Aye aye! I was pretty bummed at this point as I began t' peel t' front paper off o' t' letters and had a revelation. Begad! Ahoy! T' front paper was thar for a reason. Avast, me proud beauty!

I hoped I be right and smoothed t' front paper back down. Ahoy! I then peeled off t' back paper, t' side with t' sticky stuff. Avast, me proud beauty! T' front layer was translucent enough that I could see t' lettering. Avast! Begad! Usin' t' front paper t' hold everythin' in place, ya bilge rat, I placed t' letters and smoothed them down. Aye aye! Then I peeled t' front paper off and almost cried for joy that I made this discovery before tryin' t' do things t' hard way.

I continued me way down from t' "United" lettering. I needed t' apply a black band around t' circumference. Begad! This went on easy enough. Arrr! It did nay close all t' way either but t' fit be better than t' roll pattern and only had about a 1/32" gap. I was able t' stretch t' vinyl enough t' compensate for that.

T' "States" letterin' came next and it went on as easily as t' "United"'s did. I was startin' t' like this vinyl stuff.

Next was a narrow black band around t' top o' t' fins. Ya scallywag! Avast, arrr, me proud beauty! I looked and looked and could nay find it on t' master sheet for t' vinyl. Begad! I finally remembered seein' it in t' box loose. Begad! I identified it as automotive pin-striping. This was more than long enough t' go around.

T' final vinyl was t' mission ID. I went with MR 8 and placed t' sitckers above each o' t' fins. Begad! I had four left over and do nay know whether they are extras or if I just could nay find t' correct placement.

With that, me hearties, t' main body o' t' rocket was done and all that was left was t' capsule.

T' project sat around without any work for a long time because I had ordered a custom chute for it and because I lost t' capsule decals. Ya scallywag! When t' chute came in, arrr, I decided t' make a rush effort t' get it ready for a club launch. Arrr! I had nay put on t' launch lugs earlier because I wanted t' use a linear rail lug. Arrr! T' lug be placed and t' screw holes were marked and drilled. A thin layer o' epoxy be then put on t' bottom o' t' lug and in t' holes and t' lug replaced and t' screws tightened.

T' resin capsule be also a bit tight so I gingerly took it t' t' belt sander and removed some material around t' circumference.

As it turns out, it did nay make that launch because I could nay find t' right motors. Well, blow me down! Blimey! Begad! Blimey! That gave me t' chance t' find t' capsule decals and get it done right.

As it happens, though, Sheri read o' me losin' t' decals on TRF. Avast, me proud beauty! She contacted me and offered t' send replacements and did so without any charge. Ya scallywag! Nay too long after, a package showed up at me house and in it were t' replacement decals for t' capsule along with another decal guide. Ahoy! I want t' extend a public thanks for t' kindness.

When I got back t' work on t' Redstone, me hearties, arrr, I noticed t' capsule needed some touchin' up before I applied t' decals. Avast, me proud beauty! It took it back t' t' booth and sprayed it with black again.

When t' paint had about two days t' dry, I got started on t' final set o' decals for t' capsule. I began with t' "United States" on opposite sides, ya bilge rat, just t' t' left o' t' hatch and window. Well, blow me down! Begad! Next came t' US flags centered under t' national text. Well, blow me down! Begad! I chose t' go with t' Liberty Bell mission because I perceived that it would be easier. Begad! Ahoy! I don't know how true that really is but its what I did. Ahoy! T' mission ID tags were centered under t' hatch and window. On one o' them, ya bilge rat, I managed t' tear off t' "7" and it proved completely irretrievable. Ya scallywag! T' final decal for t' capsule was t' crack. Ahoy! Mine isn't located exactly where t' documentation said; thar be nay room for it in that position as I understood it. Aye aye! Doubtless, arrr, arrr, I got somethin' wrong but I'm goin' more for t' "look and feel" than a real scale model.

Throughout t' later part o' this build, me hearties, somethin' had bothered me about t' LES tower. Ahoy! Most o' it looked fine but, when it was set on t' capsule, matey, me bucko, it was jarring. Avast, me proud beauty! I finally realized what was botherin' me when Delta IV posted some photos o' his on TRF. My base rin' was painted t' same bright orange as t' rest o' t' tower. Begad! Begad! His be black. His looked much better. I got out some black acrylic and brushed t' base black.

T' acrylic dried smartly and, finally, me hearties, t' tower was ready t' be mounted on t' capsule. Well, blow me down! A bit o' epoxy was put around t' t' o' t' capsule and t' LES was set in place.

T' basis o' me shock mount be a length o' t' extra heavy Keelhaul®©™ tied t' t' internal eyebolt. Well, blow me down! Avast, me proud beauty! T' this was tied a length o' heavy braided nylon rope usin' a double sheet bend. Well, me hearties, blow me down! Since I wanted t' fly with t' LES attached and I worried about it shearin' under stress, I decided t' try an idea I had read about and chain stitched both t' Keelhaul®©™ and t' nylon in an attempt t' gentle t' deployment a bit. Begad! A loop be also tied into t' nylon about 2/3 o' t' way t' t' capsule t' attach t' chute harness. Avast! One o' t' things I wanted t' avoid durin' recovery be t' LES hittin' t' ground first. Arrr! Ya scallywag! In an attempt t' avoid this, me hearties, I fashioned a harness o' nylon fishin' line t' run back from t' tower t' t' braided nylon so that t' capsule would recover horizontally. Ahoy! With that, I thought me Redstone was done and that it would soon take t' t' air.

I was wrong.

Construction Rating: 4 out o' 5

Flight:
After completin' t' build, arrr, t' Redstone sat as a hanger queen for a long time due t' two unrelated reasons. Begad! T' first reason was t' chute. Begad! Aye aye! T' kit did nay come with a chute. Blimey! I be aware o' this right from t' start.

I wanted t' order a hemispherical, multi-gore orange and white chute a la NASA. Avast, me proud beauty! I contacted K&S Rockets and ordered one from there. Begad! Avast! It came in and was a beauty. Begad! It looked really nice. Begad! Ahoy! There was only one problem: It would nay fit in t' rocket. Aye aye! Avast! Recall that I had messed up with t' motor tube earlier on and t' result was less space for t' chute. T' chute I received also had thick nylon shrouds. Ya scallywag! Ahoy! I like that for t' sake o' strength but they took up too much room in conjunction with t' chute t' fit.

T' second reason t' rocket sat around for so long is that I had trouble findin' a motor for it. Begad! Orderin' by mail involved extra costs for shippin' and all o' t' local places had no short delays.

Finally, I learned that another member o' me NARRRRR section had t' right motor and no use for it. Arrr! About t' same time, matey, I started buildin' a LOC Cyclotron which did come with a chute o' t' correct size and with much thinner shrouds. Arrr! I switched t' chutes, got ready t' fly and tragedy struck. Begad! I dropped t' capsule on a concrete floor and sheared t' tower.

T' vertical members were cemented back together with Plastruct and then I started t' apply t' missin' horizontals and diagonals again.

I wept.

One o' t' things I learned is that resin does nay bounce well. Fortunately, t' damage t' t' capsule was minor and a bit o' brushed on black paint took care o' it.

Finally, me hearties, ya bilge rat, ya bilge rat, t' day o' reckonin' be at hand. Avast! I installed a Nomex shied and a LOC parachute and then inserted an Aerotech G77-4R motor. Blimey! Begad! I was thankful that t' motor came with a First Fire Jr. Avast! Blimey! igniter and I would nay have t' mess around with copperheads. Aye aye! I took it out t' t' rail, me hearties, shiver me timbers, me bucko, set it up and then had t' wait while a lot o' t' LPR traffic cleared out o' t' way.

Finally me turn came and at t' end o' t' countdown t' launch button was pushed. Avast, me proud beauty! Blimey! For a while, ya bilge rat, ya bilge rat, ya bilge rat, I thought I had misfire but I noticed somethin' was happenin' in t' motor. Then it roared t' life with a lovely red flame and started t' move. It looked good comin' off t' pad but nay too far up it angled into t' wind and kept climbing. Aye aye! When ejection occurred, I could nay tell that t' chain stitchin' made any difference at all but I did have a successful chute deployment. Arrr! Avast, me proud beauty! I could also tell right away that t' monofilament line used t' try t' keep t' capsule horizontal had nay been up t' t' task. Blimey! T' entire rig spun around on its way down, driftin' much more than I expected along t' way.

T' rocket had a hard landin' even though t' field be fairly soft. Begad! One fin had popped off and t' LES be gone. Avast, me proud beauty! Blimey! Lookin' around, one strut o' t' LES was found. While walkin' back t' t' launch area, arrr, I had already resolved t' rebuild t' LES usin' metal tubing. Ya scallywag! Blimey! I be sorry, me bucko, though that t' can portion had been lost. Then a flash o' orange caught me eye and I saw t' can lyin' nay 20 yards from t' pad. T' photos show that it was in place durin' t' ascent so me presumption is that t' shock o' t' ejection and chute openin' snapped it off and it fell t' ground nearby by shear, shiver me timbers, arrr, arrr, dumb luck.

T' rocket is repairable but will take some work before it can fly again.

Recovery:

Flight Rating: 4 out o' 5

Summary:
While this kit is nay for t' faint o' heart or t' inexperienced, it is quite workable and enjoyable t' build. Ahoy! I learned much that was new and I pushed me personal envelope with t' build. Ffor that I am thankful. Begad! Blimey! Blimey! It is a heavy kit and I would be reluctant t' try flyin' it with anythin' less than t' G77 but am lookin' forward t' tryin' it on an H some time.

My big disappointment be with t' LES tower. Begad! Blimey! Well, blow me down! Blimey! It is fragile and, shiver me timbers, in all fairness, t' instructions mildly suggest that t' rocket be flown without it so I cannot say I was nay warned. When I rebuild, though, me hearties, shiver me timbers, I will try t' do it with more durable material that can handle t' shock o' t' chute opening.

Persons interested in followin' t' exploits o' this rocket can do so here: http://www.flickr.com/photos/23694991@N03/collections/72157617574666533/

Overall Rating: 4 out o' 5