| Construction Rating: | starstarstarstarstar |
| Flight Rating: | starstarstarstarstar |
| Overall Rating: | starstarstarstarstar |
| Published: | 2014-05-20 |
| Manufacturer: | Scratch |
Brief
Here I go again. Ya scallywag! Well, blow me down! For those o' you that have followed my Goonyness this was Baby Bertha kit bash #14. Again this is nay a kit review o' t' original Estes Hawkeye (Kit #0873) [1986-1996]
It is another o' me many kit bashes. Begad! Ahoy! All fin patterns and decals came from http://www.spacemodeling.org/JimZ/est0873.htm. T' major difference again bein' that mine is a Goony version o' t' Hawkeye and as such is built with a BT-60 tube instead o' a BT-5 tube that be used in t' original. Begad! Begad! As a result it also has an 18mm motor mount instead o' a 13mm.
Components
As stated this is another kit bash so t' main components are as follows:
From Baby Bertha kit:
- 1- BT-60 Body Tube
- 1- PNC-60 Nose Cone
- 1- Launch Lug
- 1- Engine Hook
- 1- Shock Cord
- 1- Assembled 12" Parachute (transparent orange plastic)
- 1- Mylar Retainer
- 1- Green Engine Block
- 1- Blue Engine Mount Tube
- 1- Centerin' Rin' Card
- 1- Balsa Fin Sheet
From me stock supply:
- 2- Sheets Printer Paper (one for coverin' balsa and one for printin' out new decals)
- 1- Yellow E engine guide from a previous Estes kit (cut down t' two 1.5" tubes)
Construction
As with t' previous Goony builds this was a by t' book build. Begad! Instructions were down loaded and followed step by step. Ahoy! Ya scallywag! Once again t' only Con: bein' that I had t' draw and cut all new parts from fresh balsa.
Finishing
Finishin' was again done in me standard fashion o' first applyin' two coats o' Rust-Oleum 2x primmer with light sandin' betwixt coats. Blimey! Then I applied two coats o' Krylon Light Grey t' t' body while t' NC got two coats o' Krylon Gloss White. Avast, me proud beauty! Rocket was then left t' air dry over night. Well, matey, blow me down! Decals were printed on paper then clear coated with Krylon Clear Coat. After allowin' t' dry they were cut out and trimmed and attached with a glue stick as is me standard for all these kitbashes. After checkin' again t' make sure all were firmly attached I gave t' rocket two coats o' Krylon Clear Coat t' seal on t' decals. T' only Con: is that I'm still usin' printer paper to print out the decals. They would look a lot better if I could get me hands on some decal paper but I built these on a tight budget and basicly what I had on hand.
Flight
Once again t' maiden flight was at a S.M.A.S.H. Arrr! club launch on 06-20-10 and be another picture perfect flight so good that I again forgot t' take photos. Blimey! Aye aye! Blimey! That was t' only Con: I hate it when I forget t' take pics.
Recovery
This rocket has one o' t' new Estes orange plastic parachutes with a 3" spill hole cut in it which be perfect for this flight. Rocket came down at a nice safe decent speed and landed without any damage a short distance down range.
Summary
Another great flier and one more beauty to add t' me Goony fleet.
#Related Reviews
- Clone Cloud Hopper By Steve Lindeman
Cloud Hopper was my second Goonybird clone that I built by kit bashing an Estes Baby Bertha and as a result has an 18mm motor mount instead of the 13mm that the original Cloud Hopper had. Components Components used for this build were one Estes Baby Berha Kit (1261) and the plans ...
- Clone Missile Toe By Steve Lindeman
Missile Toe was number three in my line of cloned Goonybirds that was built by kit bashing another Baby Bertha kit. As such the plans and decals were downloaded from Ye Old Rocket Plans (http://plans.rocketshoppe.com/estes/est0854/est0854.htm) and used for construction guide. ...
- Clone Sky Shriek By Steve Lindeman
The Sky Shriek was clone number four of the original Goonybirds that I built. And as such is another kit bashed Baby Bertha . The plans were downloaded from http://plans.rocketshoppe.com/estes/est0855/est0855.htm . I then followed these to build the Sky Shriek with the ...
- Clone X-15 By Steve Lindeman
In all fairness I can't do a brief description on this kit as there is a small story behind it. As is normal for me this is not an actual review of the Estes NASA X-15 (0889) [1988-1989]. It is a kit bashed, clone by transition. I came about the idea of doing the X-15 as the G-15 after ...
- Clone Zoom Broom By Steve Lindeman
Zoom Broom was the 1st of my Goonybird clones modified for 18mm motors as a result of being kit bashed from a Baby Bertha. Components Starting with a Baby Bertha kit (EST 1261) that I purchaced at my local Hobby Lobby, all components except the balsa wood and decals were used to ...
- Excelsior Rocketry Der Goony Max By Bill Eichelberger
Der Goony Max is an inspired bit of lunacy from Excelsior Rocketry, and I guess depending on where you stand on the Goony issue, this series is either genius or a waste of a good Baby Bertha. Speaking as the one-time-owner of an original Goonybird Cloudhopper, I happen to fall on the genius ...
- Kit Bash GoonAries SST By Steve Lindeman
Here I go again. For those of you that have followed my Goonyness this was Baby Bertha kit bash #10. Again this is not a kit review of the original Estes Aries SST (Kit #1927) [1983-1984]. It is another of my many kit bashes. ...
- Kit Bash Goony Target Drone By Steve Lindeman
Lucky or unlucky? For those of you that have followed my Goonyness this was Baby Bertha kit bash #13. As such I wanted to play it a little safer with this one so I choose a simpler design. Again this is not a kit review of the original Estes ...
- Kit Bash Goonymarc By Steve Lindeman
The Goonymarc was number eight in my line of modified Baby Bertha kit bashes. I started with the plans from Jim Z's for the Estes kit #654 with the thought of building the glider version of the Bomarc but ended up with the parachute version (kit #657). All templates and decals for this build ...
- Kit Bash NASA Goonasus By Steve Lindeman
One again this is not a kit review of the original NASA Pegasus (Estes Kit #1376) [1982-1986] but another of my many Baby Bertha kit bashes (#12 for those following my Goonyness). All fin patterns and decals came from http://plans.rocketshoppe.com/estes/est1376 ...
- Kit Bash Snarky Jr. By Steve Lindeman
The Snarky Jr. (a.k.a. Goony Shark) was kit bash #6 in what was to become a long list of Baby Bertha's that I converted into various Goony Birds and such. The inspiration for this one of course came from my DynaStar's - Snarky and the fact that I wanted to be able to fly it in the smaller ...
- Kit Bash Streamliner By Steve Lindeman
The Streamliner was the fifth in a series of Baby Bertha kit bashes that I did while building my Goonybird fleet. The first four kits were used to make four of the original Goonybirds from Estes but now it was time for somthing a little different. I remember seeing this model in a&n ...
- Kit Bash USGF Goonasus By Steve Lindeman
For those of you still following my Goonyness this was Baby Bertha kit bash #11. Again this is not a kit review of the original but another of my many kit bashes. All fin patterns and decals came from http://www.spacemodeling.org/JimZ/est0806.htm . The major ...
- Kit Bash USSF Goonyflash By Steve Lindeman
For those of you following my Goonyness this is Baby Bertha kit bash #9. So OK this is not a kit review so much as it's actually another of my kit bashes. All fin patterns and decals came from http://www.spacemodeling.org/JimZ/estes/est1909.pdf . The main ...
- Mo' Skeeter By Chris Gonnerman
This is my Mo' Skeeter, a 320% upscale of the classic Estes Mosquito . It's a rear-ejection model, which avoids the visible nose cone line that most Mosquito upscales suffer from. Components This rocket consists of a Baby Bertha cone , 6" of BT-60, 6" of BT-20, two 20-60 ...
- Modification Baffled-Boat-Tailed-Bigger-Baby-Bertha By Mike Goss
It all started one day after I opened a Baby Bertha kit and found that the motor mount had the wrong size adaptor rings. The rings were for a BT-50 and not a BT-20. I thought about replacing the rings with a correct set, but then the creative juices started to flow, what could I do with this ...
- Modification BioHazard By Dwayne Shmel
This is a kit bash of a Baby Bertha that transforms a mild mannered rocket into mean, green, flying machine--the BioHazard. Modifications: One challenge was the tight fit of three 18mm motor mount tubes inside the BT-60 body tube. The 3 tubes were glued together and the inside "hole" was ...
- Modification Sky Goon By Stan McKiernan
This is a Goonie of one my favorite classic boost gliders, the Sky Dart. The Sky Goon starts as a Baby Bertha and adds wings, stabilizer and engine pod. Modifications: The rear of the nose cone is removed, leaving about 1/2" of shoulder which is glued to the body. The engine mount is built ...
- Scratch Streamliner By Mark Van Luvender
I chose to build the Streamliner for this contest as it truly spoke to me as something I could do--that doesn't happen often. This rocket started out as an Estes Baby Bertha kit. In order to create the "Streamliner", I cut a wedge shaped section out of the body tube starting just below where ...
Related Products
Sponsored Ads
 |
 |