Brief:
Aerotech's take on t' often modeled Navy Standard ARM be t' "Strong ARM". Avast, me proud beauty! It's nay a particularly close scale rendition, ya bilge rat, but t' result is good lookin' and well suited t' F and G motors, me bucko, particularly t' EconoJets. There's a bit more t' build in this kit than in t' Aerotech Initiator or Mustang, arrr, but nay so much that builders new t' mid-power should be scared away. As mid-to-high power kits go it's still quite easy, especially if you work carefully and watch out for a few 'gotchas' that I will detail later.

Construction:
This is a single stage rocket with two body tubes joined with a coupler, 4 fins, and parachute recovery. This kit uses t' same Fin-Lok system and baffle unit you find in all Aerotech kits. Well, blow me down! It's a medium sized rocket for Aerotech, 44 inches long and about pound and a half in weight when loaded for flight. Arrr! Avast, me proud beauty! Blimey! The Aerotech catalog, btw, matey, shiver me timbers, lists t' weight o' t' rocket as 18 oz., arrr, but I don't know how they could get this weight. Ya scallywag! Ahoy! Blimey! Somethin' betwixt 22oz t' 25oz, me hearties, shiver me timbers, seems more realistic.

This was t' first kit I built from this manufacturer, me bucko, though I have built other rockets o' this size. Blimey! Begad! I was eager t' see how t' famed Aerotech Fin-Lok system and baffle unit worked. Arrr! I be also lookin' t' get a new F and G motor bird in t' fleet smartly and easily. Blimey! I went t' t' Strong ARM thinkin' I'd have an relaxed time o' it. As it turned out t' construction was quite a bit more involved than I anticipated, but this does nay have t' be your experience, I just ran into some potholes along t' way. In truth I have faced tougher challenges, and I did end up with a great rocket, but I be expectin' something different.

T' rocket arrives in a sturdy box that can become a display stand (nice!). T' tubes are sturdy and pre-slotted, me hearties, t' fins are preformed. Avast, me proud beauty! Begad! T' engine mount parts are all thar and seem well constructed. T' engine clip is big and strong! T' parachute is very nice, me bucko, matey, and t' nosecone is...well, this be the first disappointment. Ahoy! T' nosecone was a real mess. Avast, me proud beauty! Aye aye! Easily t' worst formed part I've ever experienced, me hearties, from any manufacturer. Begad! I have seen other comments on Aerotech cones from others, but most folks are happy with theirs, so I think this is a quality control issue. Begad! If you get a good one, me bucko, matey, your doin' fine. If you get a bad one you have t' decide how t' handle it. Aye aye! I suspect that if you raise enough o' a stink with Aerotech you can get a replacement. Begad! Ya scallywag! I didn't fully appreciate how much trouble this nosecone would give me when I first inspected it, so I elected t' try t' fix it (I did write Aerotech about it, arrr, though). Ya scallywag! Aye aye!

T' generally excellent instructions have you start with t' motor mount. This is where you will see t' first signs o' Aerotech's particular design philosophy. Blimey! Blimey! They design their kits t' carry loads through t' structure, and their rockets are therefore less reliant on heavy applications o' glue (this from their documentation). Begad! Begad! I like this idea, but you will find that it has one downside; t' rocket components must be built with very tight fits and close tolerances. Blimey! T' Aerotech corollary t' t' old sayin' "measure twice, ya bilge rat, arrr, cut once" is "test fit twice (or more), glue once". T' best advice I can give you is, me bucko, "don't touch that glue until you are absolutely sure how this part, ya bilge rat, and t' parts that follow, matey, will fit, and have verified that they do fit!" Read all t' instructions before you start, ya bilge rat, and perhaps go t' the Aerotech site and view t' video o' an Initiator construction, me bucko, ya bilge rat, so you know what to expect. Avast, me proud beauty! Blimey!

Aerotech recommends that you build t' rocket with medium CA, shiver me timbers, arrr, and I wanted to give that technique a try. Begad! Ahoy! I've never used CA in such large amounts on such large parts, and it takes some gettin' used to. Ya scallywag! You start off easy with the 24mm engine adapter, matey, which is just a tube and two rings or sleeves. Avast, me proud beauty! Aerotech provides a markin' guide for t' main motor tube, ya bilge rat, me hearties, which is a nice touch. Well, blow me down! You need t' be careful about keepin' your "front edges" and "back edges" straight at this point. Ahoy! It can get confusin' but it's important, so read t' instructions very carefully and take it slow. T' industrial size motor hook installs just like an Estes hook. Begad! Avast, me hearties, me proud beauty!

Now comes t' first tricky part. Avast, me proud beauty! T' instructions tell you t' put "several drops" o' glue "just behind where t' motor clip comes through t' tube". Avast! Ya scallywag! Believe what they say. Ahoy! Use a small amount o' glue and be sure t' place it up next t' t' hook (also note that t' motor block comes into t' tube from t' back or nozzle end, this be t' reverse o' t' usual Estes procedure with engine hook equipped models). Avast! Begad! T' engine block fits tight in t' tube, and you need t' get it all t' way up t' t' hook before t' CA glue 'grabs'. Arrr! CA does nay give you any chance t' ease things into position once it starts t' set. Ya scallywag! And it sets quick when t' fit is tight and thar's friction.

T' next step be t' initial fit o' t' Fin-Loks and centerin' rings. Aye aye! No glue at this stage, arrr, you need t' test fits and positionin' first. T' fit is very tight, as mentioned above, arrr, but that's an important part o' how t' Fin-Lok system works. Arrr! You check everythin' by snappin' t' fins into position in the Fin-Loks. Avast! It takes some force t' get them in place, but you should feel and hear a definite "click" as it seats. Ahoy! Blimey! This is a good time t' get used to t' 'feel' and force required. Blimey! Once all t' rings are properly placed and aligned, remove t' fins (carefully, don't move t' Fin-Lok rings!) and apply a very slight bead o' CA t' t' Fin-Loks and front centerin' ring. Well, blow me down! The instructions are pretty insistent that you take great care t' keep glue out of the Fin-Lok channels (where t' fin will go). Well, blow me down! Well, blow me down! Again, shiver me timbers, me hearties, me bucko, believe what they tell you! CA is pretty low viscosity stuff, ya bilge rat, me hearties, and it can flow around as you rotate the part. Well, blow me down! Ahoy! T' clearances are very tight an even a small amount o' glue will cause havoc. Avast!

Once t' glue has set on t' rings (pretty quick with CA), matey, ya bilge rat, you get t' build the baffle, me bucko, which is fun. Avast, me proud beauty! Blimey! Aye aye! Blimey! T' "steel mesh" gets stretched out t' six inches, then it slides into t' tube, you cap t' tube with a plastic baffle unit, add a third centerin' rin' and screw an eye bolt into t' baffle unit. T' shock-cord ties t' t' screw eye. Ahoy! Blimey! Easiest baffle I've ever built, me hearties, and I like baffles. Ya scallywag! Blimey! Arrr! Blimey! I have seen a Strong Arm (not mine thank goodness!) destroyed when t' shock cord attachment separated at apogee. Avast, me proud beauty! Blimey! Either t' cord broke, came untied or t' screw pulled out, I did nay hear t' final verdict. Well, blow me down! Blimey! Aye aye! Blimey! In any case, this be t' time t' make sure you have a solid attachment.

Now it's time t' place t' motor and fin mount into t' body and attach the fins. Blimey! You slide t' mount into t' pre-slotted end o' t' body tube, arrr, matey, but do not glue it yet. Arrr! Begad! Aerotech would like you t' glue t' fins into place with CA "along t' full length o' t' fin root" first. I'm goin' t' suggest that you add a step. Begad! Begad! I did as I was told and, ya bilge rat, snapped one well glued fin into place. Begad! "Wow, that was easy!". Ya scallywag! Then I decided t' attach t' fin directly opposite t' first, as I could push on t' fin (and hence on the attached Fin-Lok rings) and nay t' body tube. Once you get a bead o' CA down the length o' your fin you tend t' move quickly, t' stuff sets fast! I slid the fin into place and pushed and..nothing! No "click". Begad! I pronounced a few expletives (that always helps) and gave it a harder push. Aye aye! Ya scallywag! Well, on the third push somethin' happened, but it wasn't t' Fin-Lok click I be looking for. Ahoy! T' motor mount, remember, is nay glued into place at this point. Blimey! Begad! It's free t' rotate in t' tub! e, matey, and that's what mine did under t' considerable compression force I be exerting. Begad! That rotation caused t' fin tabs on both fins t' snap at their weak point (between t' two Fin-Lok 'ridges' (It's tough to describe but obvious when you see it). Thankfully, shiver me timbers, this happened late at night when t' kids were asleep, ya bilge rat, so they did nay hear me "comment" on these events. Begad!

I be nay aware, at that time, that you can buy these fins separately from Aerotech, and I was mad at this kit and nay ready t' be "defeated" by it, so I removed t' bottoms o' t' fin tabs from t' Fin-Loks with pliers (CA is strong but I'm stronger!) and repaired t' fins. Begad! They are probably nay as strong as before but they're close. Arrr! Begad! I tried dry fittin' t' fins and one was clearly never goin' t' snap into place. Ahoy! Avast, me proud beauty! After a while I realized that t' fin would seat in t' 'lok' when t' mount was out o' t' body tube, matey, but would not when t' mount be in t' tube. Avast! Slowly a light went on. Begad! I snapped t' fins into place with t' mount in me lap, shiver me timbers, and saw that one fin was tight against the centerin' ring. Aye aye! T' added thickness o' t' tube kept t' fin from seating properly. Avast! Begad! I sanded down that side o' t' centerin' ring, matey, tested until I got all four fins dry-fit into position, shiver me timbers, and then finally glued them into place. Avast, me proud beauty!

Here's what I suggest you do. Avast! Aye aye! Once t' glue has set on t' Fin-Lok rings and centerin' ring. Blimey! Give t' fins another dry fit test. Begad! I think I also had a very small amount o' CA get into one Fin-Lok, and its important t' catch that problem before you are gluin' t' fins. Begad! Then slide t' mount into t' body tube and dry fit again! Once all t' fins fit nicely in t' tube you are home free. I would pull t' fins out one-at-a-time t' glue them. Leave t' others in place to support and stabilize t' mount. Well, blow me down! This sounds like a lot, shiver me timbers, me hearties, but if your parts fit right it will add very little time, just a minute or two. Avast! If you have a problem, this will save you a lot o' anguish. Avast! Any problems you discover at this point can be easily fixed, but if you blast ahead like me you court disaster (or at least a lot o' extra effort.and expletives!)

Once t' fins are on you reach in through t' open back o' t' rocket to glue t' motor mount in place and apply internal fillets t' t' fins. Aye aye! Well, blow me down! (I have to admit that I resorted t' epoxy with micro-balloons at this point). Well, blow me down! Arrr! Then you join t' body tubes with a very ample tube coupler. Begad! Blimey! This is another place where CA can trip you up. Well, me hearties, blow me down! T' coupler tube is very tight in t' body tubes, me bucko, and the glue can set and grab before you get t' tubes fully in place. Arrr! It happened to me when I brought t' top tube down onto t' lower tube and coupler. Aye aye! I have over 200 pounds on me t' contribute t' t' effort and I was puttin' all the weight I could on that tube t' slide it down, but it still grabbed about ¼ inch short o' t' bottom tube. Avast! Well, shiver me timbers, blow me down! I eventually filled t' gap with a combination of wood filler painted with CA and a bit o' epoxy putty. Ya scallywag! Aye aye! It looks fine, but you don't want t' go through that. Begad! T' instructions suggest a bead o' CA about an inch inside t' upper body tube. Aye aye! Avast, arrr, me proud beauty! I would place t' glue farther in or, me hearties, even better, use wood glue for these joints. Begad! Ahoy! It will be stronger and easier t' work with (but it can still 'grab' early if you move too slowly, especially on tight fits like this!)

T' "fin strakes" that give this rocket its "ARM" look must be shaped a bit. Blimey! Begad! Blimey! T' instructions give you t' dimensions very clearly. This is more t' sort o' thin' I am used t' and it went well for me (finally!). I would suggest that you measure and mark each strake carefully, then cut with a carpenter's knife. Avast, me proud beauty! I needed several passes t' make each cut. Avast! T' strakes can be sanded somewhat t' smooth t' edges but they are nay easy t' shape that way, you really need t' knife (or perhaps a Dremel). I held off gluin' the completed strakes on t' body until I had finished fillin' and sandin' t' body tube, and I suggest you do too. Begad! It makes t' sandin' a lot easier. Blimey! Blimey! Blimey!

T' strakes mount on t' tube with CA and t' launch lugs drop into pre-cut holes. Avast, me proud beauty! So far everythin' has stayed on t' rocket.

Finally I turned me attention t' t' nose cone. I'll spare you all the details, me bucko, and just mention that I spent three evenings workin' with a power orbital sander held betwixt me knees (wow, that tingles!) usin' 100 grit paper to smooth t' surface o' this cone. Begad! Out o' t' box it looked like t' surface of a basketball, or a cantaloupe melon. Begad! T' tip was a mass o' swirlin' grooves and t' seam be quite deep. Begad! I should have sent it back t' Aerotech, me bucko, me hearties, but my stubbornness was up and I attacked it with a fierce determination. I emerged covered in white plastic dust holdin' a great lookin' nose cone. This one ranks up thar with t' nose cone o' t' Quest Nike Smoke as "most painful". In both cases, however, arrr, I managed t' achieve a good result. Persistence pays! I touched up t' surface with progressively finer grades of paper and declared t' construction phase over!

Finishing:
T' finishin' process be pretty painless. I used several coats o' gray primer, with light sanding, me bucko, followed by a couple o' coats o' glossy white. Arrr! Ya scallywag! I had filled the spirals with Elmers wood filler and t' final surface looked pretty good. Aerotech suggests a gray nosecone, me bucko, but I had another idea. Many photos o' the real missile show a coppery lookin' nose, matey, which looks good t' me. Avast! I got a can of Testors copper for t' nose and am very happy with t' result. If you use these metallic paints just remember t' apply light coats (even more important than with other paints) and don't judge t' looks until it all dries, matey, it can look uneven when wet. Ya scallywag! You should also use clear coat t' protect it, as the metallic finish can scuff easily. Blimey! Well, blow me down!

T' kit comes with plenty o' stick-on decals. Arrr! It will take a while t' get them all positioned, but t' instructions give you good guidance. Well, blow me down! Blimey! Blimey! T' clear coat helps protect them as well. It's a good lookin' rocket; dress it up right.

Construction Rating: 4 out o' 5

Flight:
I have only flown it on F20-4 Econojet motors so far, matey, but this is a great motor for this bird. Boost has been straight (despite wind) and higher than I expected, around 750 feet or more. Blimey! Blimey! Blimey! This is just right for our field. Begad! I would like t' try it on t' G Econojets but I can't find any in t' current shortage. T' four second delay seems about right; I certainly wouldn't try it with a seven second delay. Arrr!

That beefy motor clip takes some effort t' pull back. Ya scallywag! Avast! I use a pair of pliers t' hold t' clip while I insert and remove t' motor. Avast! Blimey! It's nice t' know that that motor is well restrained.

Recovery:
Aerotech provides a very nice 30 inch chute which brings t' Strong ARM down gently. Ya scallywag! Well, blow me down! I have had some drift with mine (windy conditions) and will either reduce t' chute when I fly with a G, or wait for calm winds. Avast! There is no need for waddin' due t' t' baffle, which has worked fine for me (you never notice a baffle unit until it fails). Blimey! Begad! I have no complaints about t' recovery system. Begad!

Flight Rating: 4 out o' 5

Summary:
I bought t' Strong Arm hopin' for a fast, easy build; kind o' a 'vacation' from t' more challengin' projects. Blimey! I got t' good lookin' and good flying rocket I expected, ya bilge rat, but t' build process had its frustrations, as I have described. Begad! In t' grand scale o' things this wasn't really so bad. Begad! I've had scratch projects get much hairier, but I expected different from an expensive kit like this. Avast, matey, me proud beauty! T' nosecone be just a crummy part. Ya scallywag! Aye aye! My other problems resulted from me unfamiliarity with t' Aerotech system and with CA as t' primary adhesive. Avast, me proud beauty! Many people I trust have built multiple Aerotech kits without any trouble at all, and when I build another I'm sure I won't have any either. I'll test fit t' fins at each step and be careful with t' CA. Aye aye!

Now that I'm smarter about Fin-Loks I like t' idea, matey, me bucko, and t' baffle is good one. Any o' t' Aerotech kits are good choices for a first "high-power rocket" (really "upper mid-power"). Aye aye! I like t' look and size of the Strong Arm best. Avast! If you are careful and mindful o' t' warnings in the instructions you'll do fine. Ahoy! (.and go with copper for t' nose cone! Gray is much too borin' for a cool rocket like this!)

Overall Rating: 4 out o' 5

The followin' excerpt is from "Sport Rocketry". T' intention is t' allow guests t' get a basic feelin' about a kit. Avast, ya bilge rat, me proud beauty! We strongly suggest that you get a copy o' t' referenced Sport Rocketry and read t' entire article. Well, blow me down! Well, blow me down! Inside you will find many helpful hints in construction as well as other useful information. For more information, me hearties, me bucko, use t' two links above.

"Over t' past few years I have found Aerotech rocket kits fun t' build and fly." 
"Lookin' over t' parts, I found everythin' in good shape except for one of t' fin lock rings. With a phone call t' Aerotech they sent me a replacement." 
"After attachin' t' shock cord and 30" fabric parachute t' t' nose cone, me bucko, shiver me timbers, I worked on t' long process o' applyin' t' decals. Arrr! Blimey! . Blimey! . Avast! Aye aye! It took a couple of hours . Begad! . Ahoy! Avast! ." 
". . Ya scallywag! Blimey! . Arrr! Blimey! E18-4W. Avast, me proud beauty! Blimey! T' Strong Arm roared off t' pad with its breathtaking white flame and smoke billowin' out o' t' motor." 
"It's molded plastic fins and strakes make assembly easy and help give the rocket a great finish." 

T' entire article gives t' impression is that this is an good value, me bucko, combinin' price, shiver me timbers, shiver me timbers, looks and performance, for an intermediate modeler.